Steering

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...

This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Check out this video ...

Tilt release lever or bale. Fits 1970-73 Mercury Cougar and Ford and Mustang with tilt steering columns.  Ford part number D1AZ-3D544-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Replaces Ford Part # C8AZ-2066-A Sold individually

Used wiring harness retainer bracket for mounting the steering column bracket, on most 1971 Mercury Cougar or Ford Mustang before June 25, 1971. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. There was another variation used after 6/25/71. Not sure if there was a clean switch on the steering column bracket assembly at the start of 1972. We suspect not. Ford part number D1AZ-14A163-A.

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1971 Mercury Cougar or Ford Mustang after June 25, 1971. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. There was another variation used prior to 6/25/71. Not sure if there was a clean switch on the steering column bracket assembly at the start of 1972. We suspect not.Ford part number D1AZ-14A163-L.  ...

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.

Used steering column tube retainer for the Mercury Cougar or Ford Mustang equipped with the tilt steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. Ford part # C8SZ-3499-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Used retaining bolt with nut for the fixed column on any 70 - 73 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

This used retaining clip was originally used to connect the two power steering hoses together at the power steering box. Used on all 1971-73 Mercury Cougar and Ford Mustang with power steering and V8 engines. Ford shows this item in the chassis assembly manuals and it is called a hose retaining clip, and the Ford part number is D1ZA-3E506-AC.

Power Steering Hose Manufactured in the U.S.A. Low pressure return hose.  Replaces Ford Part # d1zz-3a713-a Click this link for more clarity on power steering hoses: https://secure.cougarpartscata...

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Spindle nut kit for the 70 - 73 Cougar or Mustang. Thread size is 13/16-20, for spindles starting in 1970 on Mercury Cougar and Ford Mustang V8. Included are nut, cap, washer and cotter pin.

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individuallyCheck out our caliper tips and tricks video below: ...

Fixed steering column from a 1972 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. 1971 and 1972 appear to be the same, but we will ship one from a...

This is the manual steering gear box for 1971 Mercury Cougars. Marked SMA-R and is 22:1 ratio. It is pretty rare to find a Cougar optioned without power steering. According to Kevin Marti's COUGAR...by the Numbers book 99% of all 1971 - 1973 Cougars came with power steering from the factory. If you have a non-power steering Cougar for these years you are in the 1% club.  1972-73 manual Steering boxes had a ratio of 24:1, and were tagged SMA-R.  We offer used boxes because...

This is the manual steering gear box for 1972 1973 Mercury Cougars. Marked SMA-T and is 24:1 ratio. It is pretty rare to find a Cougar optioned without power steering. According to Kevin Marti's COUGAR...by the Numbers book 99% of all 1971 - 1973 Cougars came with power steering from the factory. If you have a non-power steering Cougar for these years you are in the 1% club. The current used steering box has a date of 1H06B, August 6, 1971. For an early 1972 Cougar or Mustang. Used...

Used upper steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column. Ford casting # D1AZ-3511-AWA.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

Reproduction thick grip Mahogany Woodgrain / Chrome steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Dark Mahogany Woodgrain steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction OE spec reproduction of the two spoke steering wheel. This is the exact size and feel as the original, and has the correct factory detail Check out this video

Reproduction OE spec reproduction of the three spoke woodgrain deluxe rimblow steering wheel. This is the exact size and feel as the original, and has the correct factory detail on the spokes and center hub. Included are the wheel, gap cover and installed rimblow switch. Check out this video

Good used pad that will most likely need to be repainted unless it is black. Not hard and crispy looking. Comes naked as shown.

Good used pad available in limited colors, call for current stock on hand. We often have black and green available but hit and miss on the other colors. The center emblem is sold separate. Engineering number as seen from the backside reads D0AA-3E662-BW, Ford part number D0AZ-3623-A

Nice used driver side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-C. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

Nuts and bolts, associated with the installation of our used 1970-73 strut rods.

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3B139-A.

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

This little cover glues onto your spoke at 6 o'clock and serves to cover the gap between where your rubber horn switch starts and then stops. NOTE: The 69 steering wheel does not take one of these covers because the bottom of the horn pad actually comes down far enough to cover the rimblow gap spacing.Replaces Ford Part #: D1ZZ-13875-C. Check out this video

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.