Steering

Good used 1970 factory installed clip for attaching the high pressure line to the power steering reservoir low pressure tube. Kind of kept the line oriented during installation of the high pressure fitting. For all 1970 Mercury Cougar and Ford Mustang with 351W, 351C or Boss 302 engines. This is more for reference, this clip is much smaller than the one found on 1971-73 Mercury Cougar and Ford Mustangs with power steering. Basic Ford part number in 1970 chassis manual is 3E506. No...

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.

High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  NOS power steering control valve seal kit.  Ford part number C3AZ-3A650-B. ...

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Reproduction 384542-S2 Power steering pump adjusting spacer for use without air conditioning. For all 1970 and later Mercury Cougar or Ford Mustang with 302 or 351W engines. Spacer dimensions: 7/16" I.D. and 3/4" thick.*Note - 351C engines use a 1/2 inch spacer.

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

Spindle nut kit for the 70 - 73 Cougar or Mustang. Thread size is 13/16-20, for spindles starting in 1970 on Mercury Cougar and Ford Mustang V8. Included are nut, cap, washer and cotter pin.

Reproduction spool for the control valve on your 67 - 70 Cougar or Mustang.

Spring used to apply tension to the tilt locking pawl. 1967 thru 1969 required two springs due to the tilt away function. 1970 and later required only one spring.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individually

Now an inexpensive and easy way to convert 1967 - 1970 power steering cars to manual steering. This will give you a more precise feel for the road or track. Eliminates leaking systems and costly repairs. Installs in minutes with no special tools.

This is the most complete kit available for the steering box with 1 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your EARLY short shaft 1967 Cougar or Mustang steering box only with the 1 inch diameter sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a...

This is the most complete kit available for the steering box with 1-1/8 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can...

Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can rebuild your box with this kit. SMB-K, SMB-D, and SMB-F tagged steering boxes. Probably a DIY youtube video out there for...

Fixed steering column from a 1968 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, are available, but sold...

This nice used original part will have no broken tabs as seen on our grade 'B' version. This grade 'A' part will include two metal clip-on spacers as shown. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior.

This used original part will have a broken tab so you will have to use a over-sized washer or some other clever means of properly attaching it to the underside of your dash. This grade be part will not include the metal spacers seen on our grade 'A' part. Even with a broken tab this is a much better looking and fitting part than our economy reproduction. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. ...

Inner steering column shaft for a fixed steering column on the 1970 Cougar or Mustang.

Used upper and lower inner steering column shafts for a fixed steering column on the 1970 Cougar or Mustang. Bushings will be intact and in good shape.

These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box... Our boxes are rebuilt here in the USA at a one man shop where this is all he does. Our boxes are done by a...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm.These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will...

These are the newest steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be a great buy because of the fact that they come with a lifetime guarantee. These gear boxes are not rebuilt, as are the rest of the boxes we carry, so there's also no core charge. 16:1 ratio NOTE* The supplier specifies that these steering boxes are made with new and used parts. Having issues with wobbly or loose steering? Check out our video on sloppy steering...

Used lower steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column and can be the issue when you have a sloppy feeling tilt column. The hard steel pin will often waller out the soft cast metal and cause play in the column. Ford part # D1AZ-3D651-A, casting number D1AA-3D651-AA or D0AA-3508-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

Used upper steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column. Ford casting # D1AZ-3511-AWA.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

Reproduction OE spec reproduction of the two spoke steering wheel. This is the exact size and feel as the original, and has the correct factory detail Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Reproduction OE spec reproduction of the three spoke woodgrain deluxe rimblow steering wheel. This is the exact size and feel as the original, and has the correct factory detail on the spokes and center hub. Included are the wheel, gap cover and installed rimblow switch. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...

Good used pad that will most likely need to be repainted unless it is black. Not hard and crispy looking. Comes naked as shown.

Decent offshore reproduction but nothing beats the fit and finish of a good original FoMoCo part. Checkout our used as we have multiple colors in stock. This repro pad only comes in black. Replaces Ford part number D0AZ-3623-A.

Good used pad available in limited colors, call for current stock on hand. We often have black and green available but hit and miss on the other colors. The center emblem is sold separate. Engineering number as seen from the backside reads D0AA-3E662-BW, Ford part number D0AZ-3623-A

Nice used driver side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-C. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

Nice used passenger side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-D. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

Nuts and bolts, associated with the installation of our used 1970-73 strut rods.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This listing is for a premium quality pair of 1970 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is that after they have been bead blasted they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the...

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.