Steering

C7ZA-3590-C 1967 - 1968 Power steering box pitman arm with 1-1/8" inch sector shaft. Ford part number C7ZZ-3590-C.Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

C8ZZ-3A713-A Return or low pressure hose. Low pressure hose from the control valve to insulator. 1968-70 Mercury Cougar Ford Mustang all V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the low pressure hose from the control valve to the pump. This is the lower half only. Please see part number 42301 for the upper section that works with this hose.

High pressure hose from the pump to insulator. All correct ribbing, striping, and crimping.*Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only.Stamped with C9ZA-3A719-A.

Pair of correct power steering hoses for your 67-69 Cougar or Mustang. All correct ribbing, striping, and crimping. Hoses have 5/16" fittings. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder. Part numbers: C60A-3A717-A C60A-3A714-A

C6OA-3A717-A pressure hose. Ram cylinder to control valve. All correct ribbing, striping, and crimping. Hose with 5/16 fittings used 1967-69 Mercury and Ford. *Note - Two different hoses attach between the control valve and the ram cylinder PS7U1B and PS4U1A. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders.

C6OA-3A714-A pressure hose. Control valve to ram cylinder. All correct ribbing, striping, and crimping. Hose with 5/16 fittings used 1967-69 Mercury and Ford. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder PS7U1B and PS4U1A.

Reproduction multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Does not include dipstick. Manufacurers note: In place of the paper gaskets, it is recommended that you use gray atv...

Application 1967 - 1968 - 1969 Cougar with either 289 / 302 / 351w engines with air conditioning. After 9-11-66. Casting number 7AD. 5" diameter and a 3/8" sheave width.

Application, 1968 289/302 engines without air conditioning, but with a single alternator belt. 1969 351w engine without air conditioning, but with dual alternator belts. Casting number 7AE. 4-5/8" diameter and 5/16" sheave width.

Applications, 1968 289/302 engines without air conditioning, but with dual alternator belts. 390/427/428CJ engines without air conditioning. Casting number 6AA. 4-21/32" diameter and 7/16" sheave width. *NOTE* This is a good alternative for the hard to find AG pulley.

Application could be for any 1967-69 Ford 289 / 302 /351W, but with only a single alternator belt. This is a copy of the Ford 7AA power steering pulley. This pulley mounted correctly on an OEM pump with factory brackets, will run on the second V-belt from the inside. The inner most fan belt runs the alternator. You would be using a single belt on the alternator. Correct application is for 1969 with 351W engines. 5-1/4" diameter and 3/8" sheave width.

Application, 1967 - 1968 - 1969 - 1970 390 / 428CJ engines with air conditioning. Casting number AF. 5-3/4" diameter and 5/16" sheave width.

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...

Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting. 

Good used part without excessive rust or damaged rubber. For use with fixed column only.

This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Reproduction steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 - 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

New old stock power steering ram cylinder boot and bushings. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C6OZ-3C651-A.

New old stock power steering ram cylinder boot, rubber boot only. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C3AZ-3C651-A.

This new reproduction power steering ram cylinder is good quality with almost no warranty claims. However, When you go to put your cotter pin in the castle nut you will often find it does not align perfectly which means you may have to drill it for a perfect fit. Keep in mind we will pay $30 in in-store credit for a clean original used ram cylinder so don't throw them away! RAM BOOT SOLD SEPARATELY. Replaces Ford Part #: C3DZ-3A540-A or C7ZZ-3A540-A. ...

This an original, rebuilt power steering slave / ram cylinder. It has not had a cosmetic restoration so it will show external dings, scrapes and general wear associated with a 50 year old part located on the bottom of a car. If you buy our reproduction ram do not throw away your core used ram as we often can give in store credit for the part. RAM DUST BOOT SOLD SEPARATELY.Replaces Ford Part #: C7ZZ-3A540-A.

Quality complete rebuild kit, includes all hardware shown. Premium flexible rubber boot that has vent holes, boot for elbow, and all hardware designated by an experienced rebuilder for completeness. This is the best known kit on the market.

Most complete kit available for rebuilding the late 1967-70 Mercury Cougar or Ford Mustang power steering control valve. Includes a very accurate sleeve, all 4 seats, and various seals and hardware. Please note that the early 1967 control valves did have 1/4 inch lines. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #:...

Great kit for those that have a good used power steering control valve unit to rebuild.  Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #: C2AZ-3A533-A.

This is a replacement relay for the discontinued original FoMoCo relays.  It does not appear in the same form factor, but will work just fine. The original is a metal cased unit, the replacement is plastic.  Original relays are marked either C7ZA-3E553-A (1967) or  C8ZA-3E553-A (1968 & 1969) on the mounting tab. Click Here to Download Instructions (340Kb pdf). Replaces Ford Part # C7ZZ-10B926-A or C8ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at...

Used tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight. These relays are tested by our electrical department. Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.*NOTE* For tilt column service, you can contact...

Used release lever for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is sometimes also called a bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Reproduction repair kit for your 69 - 70 Cougar or Mustang Midland brake booster inner control valve.When doing the repair on your booster control valve, be sure to use any type of synthetic blend grease and lubricate the following:Inside lower end of the bellows, all O rings and insides of the seals and inside the front diaphragm.Included in this kit are 3 O rings, fiber washer, rubber valve, spring and spring seat and spring retainer.

These clever kits allow you to replace the broken cam without having to swap the whole assembly. Mounting hardware is included. Works on 67-72 fixed columns and 67-73 tilt columns. Replaces Ford Part # C7SZ-13318-B and D0AZ-13318-A. Watch Install Video

Replaces Ford Part # C8AZ-2066-A Sold individually

Used steering column tube retainer for the 67 - 69 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. This are not advisable in the 1970 and later cars. Ford part # C7SZ-3499-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Used retaining bolt with nut for the fixed column on any 67 - 68 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

[No Description Provided]

[No Description Provided]

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.

High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...

Reproduction rubber roller for the metal tilt cover plate on any 1968-69 Ford, Mercury, or Lincoln. Often times the rubber disintegrates over time. This is needed to keep the cover plate tight to the side of the steering column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

New screw for attaching horn pads onto steering wheels 1968-69. 2 or 3 required, sold individually.

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  NOS power steering control valve seal kit.  Ford part number C3AZ-3A650-B. ...

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.