Sheet Metal

This reproduction hood hinge nut and bolt kit fits both the Standard and XR7 and is sold as a kit as pictured. These connect the hinge to the hood itself, and connect the hinge to the fender apron.

Good used OEM original hood hinge set. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. Fits 1971-73 Mercury Cougar and Ford Mustang. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the springs.Ford...

These reproduction hood latch support bolts fit both the Standard and XR7.

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Quality inner wheel house made by Dynacorn patterned off of Grade A used panels provided by West Coast Classic Cougar.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box.

Quality inner wheel house made by Dynacorn patterned off of Grade A used panels provided by West Coast Classic Cougar.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation.

This listing is for the outer wheel house on a 1967 or 1968. Often when you replace the skin you will find multiple soft spots in the outer wheel house, especially down low. If you do not want to pay the oversized shipping on these large items we do sell patch panels.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This listing is for the outer wheel house on a 1967 or 1968. Often when you replace the skin you will find multiple soft spots in the outer wheel house, especially down low. If you do not want to pay the oversized shipping on these large items we do sell patch panels.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This listing is for the outer wheel house upper patch for the driver side of your 67-68. 

This listing is for the outer upper wheel house patch for the passenger side of your 67-68.  

This listing is for outer wheel house lower patches, front and rear for the driver side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

This listing is for outer wheel house lower patches, front and rear for the passenger side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 67 did NOT have the cutout for the side marker light and the 68 did.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 68 has the cutout for the side marker light and the 76 does not.

This used driver (left hand) side lower front fender patch panel is rust free with no prior damage. Cut with a plasma cutter, removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 69 has the small side marker light, and the 70 has the bigger, recessed side marker light. ...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 67 does NOT have a cutout for the side marker light like the 68 has.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 68 has the cutout for the side marker light, and the 67 does not.

This used passenger (right hand) side front lower fender patch panel is rust free with no prior damage. Cut with a plasma cutter and removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 69 has the smaller side marker light and the 70 has the bigger, recessed marker light. ...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

This used driver (left hand) side lower rear fender patch panel is rust free with no prior damage. Cut with a plasma cutter, removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. ...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

This used passenger (right hand) side rear lower fender patch panel is rust free with no prior damage. Cut with a plasma cutter and removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. ...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Used driver side upper front fender nose section. Rust free with no prior damage. Cut with a plasma cutter behind the leading edge of the wheel well. There are minor differences between the 71, 72 and 73 Fenders, but this fender nose section is the same for all three.

Used passenger side upper front fender nose section. Rust free with no prior damage. Cut with a plasma cutter behind the leading edge of the wheel well. There are minor differences between the 71, 72 and 73 Fenders, but this fender nose section is the same for all three. ...

Premium quality reproduction patch panel for the rear of the driver side (left hand) quarter panel on the Mercury Cougar. 

Premium quality reproduction patch panel for rear of the quarter panel on the passenger side (right hand) of the Mercury Cougar. 

Reproduction patch panel for the wheel lip on the driver side (left hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge.  These panels are made from 20 gauge (.036-.037) steel, typically cut 23" x 13"

Reproduction patch panel for the wheel lip on the passenger side (right hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge.  These panels are made from 20 gauge (.036-.037) steel, typically cut 23" x 13" ...

Reproduction patch panel for the wheel lip on the passenger side (right hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

If you are buying our one piece Mustang floor pan or our driver side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...

If you are buying our one piece Mustang floor pan or our passenger side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...

Reproduction rear floor patch panel for the 67 - 70 Cougar. This is the floor pan directly to the inside of the driver side wheel well, and has the holes for the rear seat belt bolts. Cut in house from a complete reproduction trunk pan. NOTE* If you buy both sides left and right we can leave them as one continuous panel at no extra charge just for the asking, please leave a note on your online order in the comments section. ...

Reproduction rear floor patch panel for the 67 - 70 Cougar. This is the floor pan directly to the inside of the passenger side wheel well, and has the holes for the rear seat belt bolts. Cut in house from a complete reproduction trunk pan. NOTE* If you buy both sides left and right we can leave them as one continuous panel at no extra charge just for the asking, please leave a note on your online order in the comments section. ...

Trunk patch panel cut in house from a complete transition panel. This is a patch for the area forward of the fuel tank just before the transition hump. 

Reproduction driver side rear quarter extension panel for the 67 - 68 Cougar. This is the panel that the quarter extension mounts to.

Reproduction passenger side rear quarter extension panel for the 67 - 68 Cougar. This is the panel that the quarter extension mounts to.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" driver (left hand) side rear quarter panel. We ask that you call to discuss condition, price, and cut...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" passenger (right hand) side quarter panel. We ask that you call to discuss condition, price, and cut...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" passenger (right hand) side rear quarter panel. We ask that you call to discuss condition, price, and cut...

Finally, a quality reproduction replacement quarter panel skin for the 67 - 68 Cougar! The days of searching for good used $1000 quarters are over. This new quarter panel skin is a direct fit. Die Stamped with Excellent Quality 19 Gauge Steel like the factory used.  This skin does not include the rear quarter extension panel, you can find it here. Replaces Ford part number C7WY-6527841-AKeep in mind that this item is over-sized and will cost about $275 to drop...

Reproduction driver side (left hand) quarter panel skin for the Mercury Cougar. These skins are made in America, but are low quality. These are made for the coupe, but can be made to fit a convertible. The 1969 and 1970 are not the same dimensions from the factory, the 1970 model year increased the wheel opening to allow for the optional larger tire size offered in 1970.  The 1969 wheel opening measures at approximately 29-1/2" while the 1970 unit comes in at approximately 30-1/2". This...