Seat Frames & Parts

Comes with everything shown to replace tracks on one seat, good quality reproduction made in China. Make sure and check out our good used originals if correctness is important to you.

3/8-16X1-1/8 Grade 5 flange bolt for attaching bucket seat tracks in any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, 4 needed for each seat. Replaces Ford part number 56340-S2.

This listing is for the person who needs a little more leg room when behind the wheel. If your knee is pushing on your turn signal lever, or if your belly is hitting your steering wheel, this is the item for you. Very easy to install, bolts right up to your existing seat tracks. You can expect about a 1/4" height difference. Sold as a pair, enough to do one seat. Check out this video

Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Sold individually.Replaces Ford Part # C5ZZ-13190-K

Sold in a set of eight, these are the same gauge steel as originals. Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Replaces Ford Part # C5ZZ-13190-K

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

Hard to find New Old Recent Stock switch for the driver side power seat on the 71 - 73 Cougar or Mustang. Toggle switch looks accurate, however, you will need to reuse your original plugs. PLUGS NEED TO BE CHANGED FOR SPECIFIC APPLICATION. Some of the Ford part numbers include: D1WB-14B723-AA, D1WB-14B723-Ab, D2WB-14B723-AC, D1ZB-14B723-AA, D1ZZ-14A701-A, D2WY-14A701-A.

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

Used actuator for the seat back release on the 1970 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

Used bezel for the dual head rest found in the Mercury Cougar or Ford Mustang. This bezel measures 3 1/2" long and is correct for all 1968 models that use this part (including Shelby and Ford Mustang except the XR7 Mercury Cougar. Due to extra thick seat foam, the XR7 uses a taller bezel. Good used part with no peeling chrome or obvious cracks (may have hairline crack in threaded area). Ford originally had a special tool for installing and removing these guide sleeves. Ford tool division was...

Used bezel for the dual post head rest for the Mercury Cougar XR7. This bezel measures 4" long and is correct for the XR7. Due to extra thick seat foam, the XR7 uses this taller bezel. Good used part with no peeling chrome or obvious cracks (may have hairline crack in threaded area). Ford originally had a special tool for installing and removing these guide sleeves. Ford tool division was known as Rotunda. Down deep near the threads is a molded hex shape that allowed a tool to tighten without...

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561693-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561692-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

Core driver side (left hand) and passenger side (right hand) pair of high back bucket seats for the 1969 Eliminator Mercury Cougar. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. The difference between 1969 and 1970 high back buckets is that the 1969 had the release located mid way up the side and 1970 had it down low. Seat tracks are sold separate. Seat hinge covers...

Core driver side (left hand) and passenger side (right hand) pair of bucket seats with center seat release for the Mercury Cougar or Ford Mustang. The seat frame is the same in the standard, decor or XR7 and are the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available...

Core driver side (left hand) bucket seat frame with center seat release for the Mercury Cougar or Ford Mustang. This unit is the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and D3ZZ-6560763. We also have B...

Grade A used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and D3ZZ-6560762. We also...

This desirable option was used only on the driver side seat of the LATE 71-73 Cougar and Mustang. This is for seats that have the seat release knobs on the outsides of the seats. The early 71's had the release in the center of the seat. It can be installed on the passenger side with no modification other than extending the wiring that runs under the carpet.  Before we send out a system it will have been tested and will work in all positions and will not show excessive wear or...

Core bench seat for the 1968 Mercury Cougar or Ford Mustang equipped with decor interior. 1968 bench seat without optional headrests, but with seat seat back release latches. The foam will almost always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Keep in mind 68 and 69 are identical except for how the head rests attach. You can easily add head rests from 69 buckets and bolt them to a 68 pair of buckets or bench if you have all the...

Used core bench seat taken from a Western parts car. Will need new foam and upholstery, but solid and complete with headrests. If you would like to put this in a 68 they are in fact identical once the 1969 single post headrests are removed. Does not include seat tracks.

Note: The set you receive may not be the ones pictured and will usually be in better condition than shown. The chrome bezels will all be in good matching condition, unlike the blemished one in the picture. Call if you need more details or to check inventory on colors. Used pair of dual post head rests for the Mercury Cougar or Ford Mustang. These ultra rare head rests were an option in 1968 only and may come with some slight blemishes. Your 1968 Mustang / Torino / Thunderbird / Cyclone seat...

Currently out of stock. Do you have a pair for sale? Let us know! Four required per car, bolts to the back side of the upper portion of your 1968 seat frame. According to the 1968 Cougar assembly manual the Ford part number is C8ZB-65610B10. This part has an adjustment to fine tune the headrest post alignment.

Good used headrest with no mounting hardware included. No cracks. We never have more than one of these in stock as a single so we most likely will not be able to produce the color of your choice but it never hurts to ask! Basic Ford part number for this item is C8AB-62611-A08. The "08" suffix part of the number may refer to a specific color.

Not rusty or water damaged, hardware sold separately. Vinyl is often UV damaged. Please indicate what color you prefer and we'll try to accommodate, but there's no guarantee we'll have it.

Rear seat bottom or lower cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number C9WB-7663120.*Note - Does not fit coupe or fastback.Lower frame measures 46" at it's widest point and 18.5" high This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Rear seat bottom or lower cushion from any 1971-72 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that both of your seat belts anchor under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D1ZB-7663120.*Note - Does not fit coupe or...

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-7666700.*Note - Does not fit coupe, or fast back.

Rear seat back or upper cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C9WB-7666700. This part number or engineering number would have originally been stamped into a tag that was attached to the bottom side of the seat. Though these seem to fit in a 64-70 Mustang convertible, the correct engineering number that would...

1969-70 actually used a star head bolt but these are a much more user friendly screw that will work in its place. Sold in a set of four which is what you will need for one seat.

Reproduction plastic seat backs for the 1971 Cougar or Mustang.Sold as a pair

Driver side seat back release assembly, can me used for a conversion of 1970 high-backed seat backs for use in 1969 Mercury Cougar Eliminator and Ford Mustang Mach 1. This assembly has the release lever mounted nearly at shoulder level, factory 1970 high backs have the latch release at the hinge. This is a sneaky way to 'create' the factory 1969 high backed seats from 1970 seat backs. Comes with all hardware as shown. See picture for locating the three holes required for installation in a 1970...

New Old Stock Ford bracket with attaching parts. Repairs the Driver Side bucket inner seat pivot. Ford service replacement part.A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat...

New Old Stock Ford bracket with attaching parts. Repairs the Passenger Side bucket inner seat pivot. Ford service replacement part D7ZZ-69618C47-A. A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the...

Used driver side outer bucket seat black hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561695.

Used driver side outer bucket seat dark blue hinge cover, for any 1967 Mercury Cougar XR7. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561695.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used driver side outer bucket seat saddle hinge cover, for any 1968-69 Mercury Cougar or 1968 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used passenger side outer bucket seat IVY GOLD hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Used passenger side outer bucket seat saddle hinge cover, for any 1968-69 Mercury Cougar or 1968 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

D1DZ-6561883-A Spring that keeps tension on the adjusting seat track latch, it keeps it locked. 1971 - 1973 Mercury Cougar and Ford Mustang Bucket Seats. We think that this later spring for the 1972 and up seats was a service replacement part.

Bucket seat track set for 1972 Mercury Cougar and Ford Mustang after 12/1/1971 and 1973 cars. Our premium grade used tracks are carefully inspected for damage prior to shipping. Most likely you will have to paint, but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Kit includes brackets D2ZZ-6561704-A and D2ZZ-6561705-A. *NOTE* Not compatible with the power seat option.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.