Contact Us / Visit Us (click here)
If the Shopping Cart takes too long to respond, you can bypass the shopping cart and go straight to the checkout page by clicking the following link: Checkout.
International Customers Click Here [Updated 1/2024]
Loading Trivia . . .
'https://cdn.cougparts.com/dc/26148/1484344648_y.jpg'

Item #: 26148

Login to add this item
to a saved wishlist
MSRP:$57.49
You Save: $11.94 (20.8%)
Price: $45.55
    Cost: 3644
    Earns: 183
    Bonus: 0

    Availability

    In-Stock Item - Next Business Day

    Applications

    Description

    New disc brake proportioning valve / distribution block seal and rebuild kit for the Mercury Cougar or Ford Mustang / Torino. Every 1967-69 Cougar, Cyclone, Torino, Ranchero and Mustang equipped with disc brakes needs this kit even if you are not leaking fluid yet. These little "O" rings are always "rock hard" after 40 plus years because the original O-rings are composed of a BASIC nitrile compound. After several years, the absorption of brake fluid will change the molecular structure of the nitrile causing it to harden, contract & then crack. Our O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is designed SPECIFICALLY to withstand chemical degradation caused by prolonged exposure to brake fluid. This is a serious safety issue that you really should be concerned about. We custom made the proportioning valve spring from the exotic alloy INCONEL, which will never rust and will retain its factory specification compression strength many times longer than the originals. If your original spring is still intact, it has for sure lost its memory many years ago. The original units were never designed to last 40-50 years. This kit carries an unlimited lifetime warranty against material failure. Other terms used for this valve include Pressure Differentiation Valve, Disc Brake Pressure Control Valve, Pressure Reduction Valve or Brake Limiter Valve. Some 1967 proportioning valves are at the rear axle.

    *Note* This kit will not work with the reproduction disc brake distribution block assembly.

    *NOTE* If you have a serviceable proportioning valve / distribution block that you would like send us for credit, just mention it and we will include a prepaid shipping label and give you up to $60.

    Our video below shows how to rebuild your distribution block & proportioning valve.

    Below is an older write-up we did with pictures showing the same process. Note - this kit used to be 8 pcs, but is now 9 since it now includes the copper washer.

    Shown here are the 8 pieces of the kit for your Cougar / Mustang / Torino / Fairlane power disc brake proportioning valve and distribution block. The 1967 version not only looks different inside and out but the cylindrical proportioning valve will be located near the rear differential instead of on the driver side rear inner apron as found on the 1968-1969 models.

    The spring included in this kit will never rust. Often when you open up an original valve for the first time the only trace of the old spring will be a blob of rusty paste.

    This is what your assembly looks like on a 68-69 Mustang or Cougar. The Torino car line has different bends in the lines and a different bracket but the two components are the same internally.

    Don't even start this project until you have a quality, name brand set of line / flair nut wrenches in hand. Even with the proper tools some lines will be a challenge to remove. We recommend you save yourself the frustration and just cut the lines and purchase our new lines. After you cut the lines a box end wrench will easily remove the remaining fitting.

    Often these two lines will get ruined when you try to unseat them after being in place for decades. We suggest buying new lines before you ever remove the valve, these lines are not included in our brake line kit.

    To get this line off, wrap a rag around the cylinder to prevent scarring the brass with the jaws of your vise grips. It will want to slip on you so two pairs of vice grips will be needed in most cases. Even then the wrench will often want to round off the fitting so you may want to slip a 6 point box end wrench over the line to get to the fitting. Go borrow a quality wrench if you do not have one, if you use a "budget" tool you will just frustrate yourself and ruin parts.

    Here is a hint as to what we will find inside...

    This outer "O" ring is not really a seal but a cover designed to keep contaminants out of the weep hole. The weep hole is there for when your internal seals go bad and the fluid needs a route of escape.

    Very little of the original spring was intact on this one as you can see below...

    Getting this piston out of its housing can be very difficult depending on how much corrosion is present. On units where the piston moves freely you will be able to insert the blunt end of a drill bit in the valve to push the piston out ever so gently. On units that are froze up you will be tempted to "tap" on the drill bit to push the piston out. Very light tapping would be appropriate but what you cannot see until you get the piston removed is exactly what you are pushing on. If you tap too hard you will be destroying the little rubber ball housed in the white plastic hollow end. The rubber ball is resilient enough but the three delicate brass tabs that hold the ball in place can easily be broken off and the valve will become useless. So far the best solution we have found is using a grease gun to force the piston out. On our grease gun the end fitting easily screws off and then you thread the flexible grease gun hose directly into the valve. Of course, the piston has a small hole in the end that the grease would instantly flow through if not plugged so we thread a coarse thread screw into this hole (not too far). Next we put some heat on the end that the piston comes out of, don't do it on the other end as you may damage the plastic tip on the piston. Finally (for really stubborn examples) we place the head of the screw in a vice and for ultimate pulling power we use a claw hammer to pull as your helper cranks on the handle of a large, heavy duty grease gun. Even the most stubborn pistons will pop out when you have the high pressure grease pushing on it, the claw hammer pulling on it and the heat from your torch loosening it up! Check out this thread at mercurycougar.net to learn more. We would like to hear from those of you that have tried other methods and had success.

    The picture above shows the flexible grease gun hose attached to one end of the valve with a sheet-rock screw threaded into the hole in the brass piston. Prior to setting this up we got the end opposite of the grease gun really hot, not glowing but HOT! Look at the picture below, this came from a car that had been parked outside for 20 years. It was REALLY stuck but we can honestly say it came apart in minutes with minimal effort.

    You can faintly see the rubber ball in this picture. This is what you are pushing on so be gentle!

    These seals were still actually pliable, often they will be cracked and hard. We never find good springs, 40 or more years of being immersed in brake fluid will destroy them every time. This piston can be easily cleaned up with fine steel wool.

    Customer feedback: Hey guys! The grease gun method to remove the piston works just fine. Use the two handed long handle type of grease gun instead of the smaller pistol grip variety as you will need the extra pressure. Also, I had to put a tiny brass wood screw in the piston hole or grease just comes out the other end. Use the heat gun but not so hot that you can't touch it. Leaving the valve clamped to the mounting bracket and placing the clamp in a vice with a rag works pretty good for getting the lines off. You know your business but I don't think I would ever recommend tapping on the piston with the drill bit. An easy push would be fine but we know that rarely works. Thanks for coming up with this much needed kit! - Doug

    The distribution block is much easier to get the piston out of because you can tap it out from the backside without damaging any fragile parts. In the picture below I am using the blunt end of a size appropriate drill bit to push the piston out.

    Below are all eight pieces laid out next to the positions they were they should be reinstalled. Fine steel wool and patience will get these dirty old brass parts looking like new but I have found the best thing to use is a brass gun bore brush and ATE DOT 4 Type 200 brake fluid as both a cleaner and lubricant.

    Notice the round "O" ring to the left in the picture below. Some units will appear to be square edged like the other two. The assumption is the ring just takes on the squared look from being compressed over time and becoming hardened.

    Specifications:
    Shipping Weight: 0.20 LBS
    (weight shown may be the dimensional weight)

    This item must ship via

    review-star review-star review-star review-star review-star

    4.96 out of 5 stars
    Based upon 32 Review(s).
    5 Stars
    84%
    4 Stars
    16%
    3 Stars
    0%
    2 Stars
    0%
    1 Stars
    0%

    this brake proportioning valve/distribution block rebuild seal kit was just what my 1969 xr7 390 needed

    5.00 out of 5
    Material:
    review-star review-star review-star review-star review-star
    Fit:
    review-star review-star review-star review-star review-star
    Craftsmanship:
    review-star review-star review-star review-star review-star
    Correctness:
    review-star review-star review-star review-star review-star
    Pros:
    • easy job
    Cons:
    • no cons
    fixed the problem first time!!

    reno, nv
    2022

    High quality parts.

    5.00 out of 5
    Material:
    review-star review-star review-star review-star review-star
    Fit:
    review-star review-star review-star review-star review-star
    Craftsmanship:
    review-star review-star review-star review-star review-star
    Correctness:
    review-star review-star review-star review-star review-star
    Pros:
    Cons:
    im posting this review to give credit to wccc for their great parts and service, as well as add some helpful info that is not in the video for early model cougars.

    it is not easy to remove the spool valve from the distribution block on early models because it is a blind hole. later models can be removed easily with a punch. i ended up making a trip to home depot for some fittings to hook up my grease gun to the rear brake ports. with the collar and ferrule removed, 1/4" compression fitting threads right into the larger port and a fine thread 3/8 bolt threads into the other side. i got a 1/4 compression fitting with a female 1/8" npt female on the other side so i could thread my grease gun into it. worked like a charm to pop it right out. hope this helps someone. only ended up being about 5 bucks for the fitting.

    brake distribution block and proportioning valve

    5.00 out of 5
    Material:
    review-star review-star review-star review-star review-star
    Fit:
    review-star review-star review-star review-star review-star
    Craftsmanship:
    review-star review-star review-star review-star review-star
    Correctness:
    review-star review-star review-star review-star review-star
    Pros:
    Cons:
    easy to reseal

    Rebuild/Seal Kit-Brake Proportioning Valve/Distribution Block-Disc Brake- New-67 to 69 Merc Cougar

    5.00 out of 5
    Material:
    review-star review-star review-star review-star review-star
    Fit:
    review-star review-star review-star review-star review-star
    Craftsmanship:
    review-star review-star review-star review-star review-star
    Correctness:
    review-star review-star review-star review-star review-star
    Pros:
    • Everything needed for the job
    • WCCC was invaluable for the rebuild
    Cons:
    Never rebuilt one of these before, but mine surely needed it. This kit is complete with everything needed for the job. The WCCC tutorial was invaluable especially the part about honing the block with the wire brush.

    1968 Mustang GT 428CJ Front Pwr. Brakes

    5.00 out of 5
    Material:
    review-star review-star review-star review-star review-star
    Fit:
    review-star review-star review-star review-star review-star
    Craftsmanship:
    review-star review-star review-star review-star review-star
    Correctness:
    review-star review-star review-star review-star review-star
    Pros:
    Cons:
    Just as described in video Awesome job. Worked great!

    Number of questions: 0
    Please login to ask a question.

    Why am I being warned about potential exposure to chemicals in motor vehicle parts?


    • Some chemicals in motor vehicle parts are on the Proposition 65 list because they can cause cancer and/or birth defects or other reproductive harm.
    • When purchasing USED or NOS items, we do not know if listed chemicals are present in these products.
    • This product is known to contain the following listed chemicals:
    WCCC hooked me up with an original glove box cable and the correct screws WITH shoulders for my glove box. Their listing for these screws explains that the original screws have a shoulder for the cable and most people put in the wrong screws--which...
    - Jim Davis
    I have been a cougar owner for just shy of 30 years, I have been dealing with part problems for a very long time. The people at WCCC have always be honest, and overly helpfull. I now have a 1970 XR-7 mostly rebuilt, and my son has a 1968 base...
    - Voodochild5
    What did you LIKE about your experience? * : I am fairly new to WCCC, four or five orders (at the time of writing), but I am blessed to have found WCCC for sure. I had a small problem, couldn't find anything to work for the condensation drain on my...
    - Kenneth Milden
    I have been working with Don Rush and his team for close to 20 years. In all of these years with many sales transactions I can say they have been 2nd to none. They have always been not only helpful but extremely knowledgeable. I certainly continue...
    - Denver
    I have made many purchases online with WCCC but chose this time to make a 1400 mile round trip and visited them in person. I brought a van load of parts with me that needed a home. Don helped unload them then quickly assessed the value which I...
    - pandamonium2112
    I just wanted to let you know that my order which was shipped (via UPS Mail Innovations) December 05 was at my front door, having gone thru Canada customs, on December 16. It arrived in excellent shape. Kudos to you guys, UPS, and the USPS for...
    - Rod (Saskatchewan, Canada)
    I liked that I could see a picture of parts and that you could type in what you were looking for. What was handy for me was the ability to chat with Darrell. He was a big help. Also high on the you gotta keep on staff was Joshua, I had some issues...
    - Rod (Canada)
    I was having difficulty placing my order on the website and spent a couple of hours trying with no luck (ending in immense frustration). I decided to finally just call and order my parts over the phone (4 small items). Was surprised that Don Rush...
    - Tim (1969 Cougar XR7)
    Brake booster failed on our 1970 Mach1. We had ordered a new 2022 Mach1 to match the old one and the dealer wanted to use both cars in a promotional ad. When we received the replacement booster it failed within a few minutes of installation. I...
    - Alan
    WCCC makes finding the right part with the right fit easy. I love that they try to get great parts and when there are parts that don't meet their standard they WARN you up front! I've bought new reproduction parts from them, used parts and even had...
    - Daniel
    B1B04