Your cart is empty!
Comparative Guide of the 1970 Ford Performance Vehicles and the "Competition", which included the Cougar.
Nice pliable original seal that measures 3 5/8" tall, no burns, rips or cuts. Will trade straight across for 68-70 428 Cougar ram air seal which is only 2 1/4" in height. Ram Airs seals are designed to stretch over air cleaner bases that are approximately 14 3/8" wide at their outer most upper lip.
Spark Plug Wire Separator Brackets for the 1969 - 1970 Mustang Cougar or Torino with 428CJ Finned Aluminum Valve Covers, 1969 - 1970 Mustang Boss 302 with Finned Aluminum Valve Covers or Boss 351 models. These are an MCA approved unit made here in the USA. These replace Ford part number C9ZZ-6583-A and include both brackets and the 4 screws to properly install these units. Attaches spark plug wire holder to the factory finned aluminum valve covers
Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.
This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-4V Regular Fuel followed by white background with blue lettering and a Motorcraft, Autolite parts logo. located on the top of the air cleaner. *Note - Too small to fit the 18 inch diameter air cleaner lid from 1968-72.Fits the following models with a 351 4 barrel engine:1974 Cougar1974 Mustang
This is a reproduction of the original chrome engine displacement decal with black lettering and stripes that was located on the top of the air cleaner.Fits a 1967 Mercury Comet GT with a 390 4 barrel engine.This decal is for the 1967 Mercury Comet 390 4V GT Air Cleaner. It can be used on the Cougar but as far as we can tell the 67 390 GT Mercury Cougar did not have an air cleaner decal.
No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.
New cross drilled bolts (set of 4) for mounting 1967 brake calipers to the caliper mounting brackets. These have the correct black finish.*Trivia - these were cross drilled because the factory safety wire tied them together.
Reproduction disc brake master cylinder cap in gold cadmium for the Mercury Cougar or Ford Mustang. We have compared this cap to our originals, and the stamping does not match any of our originals, but the manufacturer claims that the scripting is correct. Also available in chrome! This cap will only fit master cylinder part# 15298Replaces Ford part # C7AZ-2162-B. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar...
Reproduction premium quality disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. These are considered concours correct and show quality. Check out the link below for some information on master cylinder caps: http://anghelrestorations.com/uploads/3/5/1/2/35122002/master_cylinder_caps_1.5.pdf Replaces Ford part # C7AZ-2162-B. Fits: 1969 Mercury Cougar1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang / Torino1970...
Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C8OZ-8600-A. This fan will also work on many small block applications. We hope...
Another spot-on reproduction by WCCC, new as of 3-3-2011! C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do offer a Hayden brand replacement fan clutch. Replaces Ford master part number...
Complete reprint of 11 Supplemental Off Highway Performance Operation Parts Newsletters from Ford which were printed between January 1972 and Spring of 1973. Full of tips on modifying your vehicle for Drag, Strip and Oval Racing.
Reproduction front tack strip for the front bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the front bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 feet (60 inches) of material and will have to trim the tack strip to fit...
Dash to engine Gauge Feed with push-on post oil sender and Air Conditioning. Should be for 1966 Falcon and Mustang. Replaces Ford Part #: C6DZ-14289
Reproduction 302 AT W / Air Engine Code Decal for the 1970 Mercury Cougar
New "Mercury" script decal in black for any Mercury, but will be at home on the Cougar. Measures 10 3/4" wide by 1 1/2" tall.This is a die-cut vinyl decal. To install, you'll have to peel off the backing, apply the decal to the intended clean surface, press in place with a plastic squeegee or credit card, then carefully peel away the top contact paper.
New interior detail spray for your Mercury or Ford that will bring out the shine and luster of your interior. This spray is for the car show when your interior has already been cleaned and vacuumed. This will not leave a wet or greasy film and will give your interior a non-glossy rich finish.
Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet. Replaces Ford part # C9AZ-2167-B.
Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 429CJ or Super Cobra Jet engines Mercury Cougar, Ford Mustang, and 1970-71 Torino/Cyclone.Fits between exhaust manifold and header pipe (H pipe) 2-13/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H pipes. Replaces Ford part number C8SZ-9450-A.
Reproduction of the 1969-70 Mercury Cougar XR7 door panel door grab handle or door pull ends and caps. Also found on 1969-70 full sized Mercury cars and 1968-70 Lincoln Continental MK III. Chromed end originally had a Mercury part number of C9MB-5422668-A, and the flat covers had a part number of C8MB-5422678-A. Nice reproduction of the covers, although we feel that they are a tad too shiney. Sold in a set of 8 pieces, enough for two door pulls.
Individual reproduction anti-rattle rubber gasket for the stainless steel accent ring used on the Mercury Cougar or Cyclone. This unit is used to keep the accent rings from rattling and driving Cougar and Cyclone owners insane. You can run your wheels without these rings, however Ford used them, so we sell'em. Sold individually.
GT 350 Holley 715 CFM center pivot bowl to bowl transfer tube.
This is not for a regular Holley 4150. These tube ends are about 12-1/2 inches apart. Dual quads?
These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common aftermarket 5-1/4" speakers in multiple depths. Sold as a pair. For more discussion on kick panel speaker options, check out this thread. Replaces Ford Part number C8OA-19A067-A ...
This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification (in states where front plates are optional), for-sale pictures, and even as standalone wall decoration. Plus it makes a great gift for the Cougar lover who has everything else!
Manual on how to modify your FE big block Ford for street or strip.
Reproduction exterior mirror pad for the passenger side sport mirror on any 1969 Mercury Cyclone or Montego, or 1969 Torino, Ranchero, etc., all with factory sport mirrors. Nice quality plastic reproduction sport mirror pad. Marked C9OB-17C701-A.Replaces Ford part number C9OZ-17724-A.
Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.
Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.
New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.
New RTV oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.
Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...
Reproduction manually adjustable convex passenger side view mirror in chrome for the Mercury Cougar or Ford Galaxie. Gasket is included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Here’s our little video that will make your mirror installation a little easier. ...
New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.
This threaded plate mounts the base to the head on all 1969- 1973 manual sport mirrors. The two fine threaded screws are accessed only by removing the mirror and using a screw driver from the bottom side of the base. This is the hardware used in our reproduction passenger side sport mirror for 1969-70 Mercury Cougar and XR7. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a...
Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.
This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.
For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.
Size SMALL Men's T-Shirt in blue featuring a 1970 Cougar Eliminator on front and WCCC logo on the back.
Size SMALL Men's T-Shirt in orange featuring a 1970 Cougar Eliminator on front and WCCC logo on the back.
New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.
New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.
Folks, this one just doesn't fit. Probably fits a 1973 or later 302 Ford, but not on the Cougar? The crankshaft center hole is 2-9/16 inches, the originals were just over 2 inches in diameter. Timing Cover not for 1967-1969 289/302/351W using a water pump with a backing plate. Features a cast-in timing pointer and dipstick hole.
Concourse Correct Timing Pointer for any 428 Super Cobra Jet Replaces Part Number C9OZ-6023-A.
Manufacturer calls this a torque pin kit, it consists of 3 pins. Pin diameter is 1/2 inch and are 13/32 inches long. Made from natural nylon. Fits most Ford vehicles with power windows from 1964 - 1973+.
New large black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 21" X 9" X 9" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!
New small black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 17" X 8" X 8" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!
New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.