Lights

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

Reproduction mounting studs for the side marker light lenses on 1970 Cougars and Mustangs. 2 required per light, 8 per car.Sold as a pair.

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

NOS fixed column turn signal switch for the 1970 Mercury Cougar or Ford Mustang. Ford part number D0ZZ-13341-A or D0ZA-13B302-C. Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

Used shutoff valve for the headlight vacuum system of all 1969-70 Mercury Cougars. Also found on 1969-70 Ford and Mercury full sized cars with hidden headlights. Additionally these were also used on 1969-70 midsized Ford and Mercury such as Torino, Cyclone, also with hide away headlamps. This is a black plastic shutoff switch or connector, 1969 cars used a white valve that crumbled from the under hood heat. Note that the indicator tabs perpendicular to the lines means 'open'. Turning the valve...

Grade "A" harness that runs from the passenger side door jamb to the courtesy / C-Pillar light. This harness is only needed if you have a Standard model car. NOTE: All XR7's would have already come equipped with his harness.

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Used steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1970-72 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is black, there is also a natural or white color version of this plug used by Ford 1968-69. Ford part number D0AZ-14489-L.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. Replaces part # D0WY-15702-A

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

NOS fixed column turn signal switch for the 1970 - 1972 Mercury Cougar or Ford Mustang.Ford part number D2AZ-13341-CNeed help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...