Lights

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Used small wiring harness with light socket that illuminates the under dash ashtray on 1969 Mercury Cougars without console. Takes a 1445 bulb, which is sold separately. This light should work on a Mustang, since they used the same ashtrays. The female bullet connector is for plugging in the heater or A/C control light. Comes with bulb shroud with clip as shown.Ford part # C9WB-13A726-A.

Reproduction small wiring harness with light socket that illuminates the ashtray on 1969 Mercury Cougar and Mustang with console. Takes a 1892 bulb, included in this reproduction.  Replaces Ford part # C9ZB-13A726-A.

Used small wiring harness with light socket that illuminates the ashtray on 1969 Mercury Cougar and Mustang with console. Takes a 1892 bulb, which is sold separately. Ford part # C9ZB-13A726-A.

Glove box or glove compartment light with switch. Fits 1969 Mercury Cougar, 1969 Ford Mustang. Used switch and wiring assembly, tested and working. 1969 has a part number C9WB-14413-B on the wire. Will work on a 1970 Cougar or Mustang. The wire on the 1969 pigtail is a larger gauge than the 1970 equivalent.Fits 69 CougarFits 69 Mustang

Used map light assembly for the Mercury Cougar standard or Eliminator. This unit has the switch installed on the housing and mounts under the dash pad on the passenger side (right hand). Assembly comes with housing, lens and wiring harness. After January 1970, Mercury changed the housing to plastic. We occasionally have those versions, please ask. This unit measures about 6-1/8" long, 1-11/16" wide and about 1-5/16" deep. *NOTE* Because this unit has the switch mounted in the housing, it...

Reproduction map light assembly for the Mercury Cougar XR7. It mounts under the dash pad on the passenger side (right hand) and comes with the housing, lens and wiring harness. Hardware included. *NOTE* This unit is not the same as the one that is used on the Eliminator or standard Cougar. The standard / Eliminator unit has the switch in the housing.

Used map light assembly for the Mercury Cougar XR7. This unit mounts under the dash pad on the passenger side (right hand) and comes with the housing, lens and wiring harness. After January 1970, Mercury changed the housing to plastic. We occasionally have those versions, please call for availability. This unit measures about 6-1/8" long, 1-11/16" wide and about 1-5/16" deep. *NOTE* This unit is not the same as the one that is used on the Eliminator or standard Cougar. The standard /...

There is not a special part number for this angled cup that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1969-70 Mercury Cougar.

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

These clever kits allow you to replace the broken cam without having to swap the whole assembly. Mounting hardware is included. Works on 67-72 fixed columns and 67-73 tilt columns. Replaces Ford Part # C7SZ-13318-B and D0AZ-13318-A. Watch Install Video

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Correct size, style, and color screw for all 1969-70 Mercury Cougar front turn signal bezels. Sold individually, 4 total needed per car.Replaces Ford part number 52445-S.

For most applications, we highly suggest you upgrade to our solid state version of this unit.  Ford part # C9WY-13350-A, Ford service replacement part # D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on...

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

Reproduction studs and nuts for the taillight to body on the 1969 - 1970 Mercury Cougar 

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

Used headlight switch for the Mercury Cougar. This original FoMoCo unit was tested and will hold 13 pounds of vacuum. The spacer (which is specific to 1969) is not included with this unit, but you can get it right here. Ford part # C9WB-11652-B.

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. For 1968, the relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash...

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

Grade "A" used harness with no cuts or splices. Correct for XR7, Eliminator, and 1969-70 Shelby Mustang GT-350 and GT-500. Ford part # C9WY-14405-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Good used 100% complete turn signal light assembly for your 1969 Cougar. Was also used on 1969 - 1970 Shelby Mustangs, GT-350 and GT-500. All clear lenses. Ford part # C9WY-13200-A for the passenger side assembly, C9WY-13201-A for the driver side assembly. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There...

Good used 100% complete turn signal light assembly for your 1969 Cougar. Was also used on 1969 - 1970 Shelby Mustangs, GT-350 and GT-500. All clear lenses. Ford part # C9WY-13200-A for the passenger side assembly, C9WY-13201-A for the driver side assembly. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There...

When your lights are sequencing too rapidly, causing the outer light to not fully illuminate, your original unit is most likely the culprit. This solid state unit replaces the small red (69-70) or green (71-73) flasher found under the dash, next to the radio. NOTE* Some vehicles have the wiring reversed, you can get though this problem by using spades and hooking up to the contacts of the flasher backwards.  This is the updated flasher unit for use with the updated sequential unit and...

When your lights are sequencing too rapidly, causing the outer light to not fully illuminate, your original unit is most likely the culprit. This solid state unit replaces the small red (69-70) or green (71-73) flasher found under the dash, next to the radio. Replaces Ford part # D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

New Old Stock turn signal switch for any 1969 Mercury Cougar or Ford Mustang with fixed steering columns. This switch will also fit fixed column Ford's 1968-1969 Ford Crown Victoria / Full Size / LTD / Fairlane / Torino / Falcon / Galaxie & 1970 Mercury Comet / Ford Falcon / Early 1970 Ford Maverick / Mercury Comet without locking steering wheel & all 1968-1969 Mercury Comet's Ford part # C9AZ-13341-B.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Used steering column wiring harness plug. Replacement plug for all 1968-69 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is natural or white, there is also a black color version of this plug used by Ford 1970-72.Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject....

Used shutoff valve for the headlight vacuum system of all 1969-70 Mercury Cougars. Also found on 1969-70 Ford and Mercury full sized cars with hidden headlights. Additionally these were also used on 1969-70 midsized Ford and Mercury such as Torino, Cyclone, also with hide away headlamps. This is a black plastic shutoff switch or connector, 1969 cars used a white valve that crumbled from the under hood heat. Note that the indicator tabs perpendicular to the lines means 'open'. Turning the valve...

Used and reusable backup lamp socket and wiring assembly for the reproduction reverse light chrome housings or to replace a damaged lead in your original 1969-70 Mercury Cougar reverse light. This light socket assembly uses the 1156 bulb. NOTE: These sockets are crimped from the factory and are difficult to remove. When re-installing, there won't be much "meat" left to flare out inside the bezel and you may run into issues with getting a good ground. 

Grade "A" harness that runs from the passenger side door jamb to the courtesy / C-Pillar light. This harness is only needed if you have a Standard model car. NOTE: All XR7's would have already come equipped with his harness.

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Used steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1970-72 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is black, there is also a natural or white color version of this plug used by Ford 1968-69. Ford part number D0AZ-14489-L.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Used bezel for the side marker lights on the Mercury Cougar or Ford Mustang. Used with front and rear 1969 marker lenses and fits almost all 1969 Ford and Mercury cars.  Ford part # C9AZ-15A440-A, casting # C9AB-15A466-A.

Grade "A" driver side (left hand) bezel with no pitting, ready to install and use as-is. Ford part # C9WB-13504 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check out this LED...