Lights

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. For 1968, the relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash...

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

Good used grade "A" taillight bezel for the 67-68 Mercury Cougar. This grade "A" unit will not have any pits, bends on the ribs and the chrome will have good luster. When you mention it in the comments section, we will try to pick out examples that still have the detail paint in tact. This no excuses bezel will look great on your high quality unrestored driver. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

Good used driver quality grade "B" bezel with no bends, cracks or deep pits. Chrome will have a decent luster (not perfect), but the paint will need to be redone. If you want show quality then the only way you will be happy is to buy our rechromed bezels. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Beautiful show quality triple-plated chrome taillight grilles / bezels for your '67-8 Cougar! Better than new. Sold as a pair. Bare chrome, so you will have to do the black detail paint yourself (see tips below). Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior...

Sold individually, right is the same as left. Needs no repaint in the reflective area and will actually be in much better condition than what is pictured. Seals will need replaced as they are original. Comes with original mounting studs. Great for Shelby or Eleanor clones. Why buy $100 ABS plastic reproductions when you can have original FoMoCo? *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

The only difference between grade "A" and grade "B" on this part is the reflective finish on this grade "B" part needs to be redone. There is a spray paint specifically for this application sold by Krylon and others. The pair you get will actually look much better than what is pictured here. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Good used pair of taillights that includes two average grade "B" bezels and two used grade "B" lenses with backing plates. No obvious cracks in the lenses but there will be stress cracks that will only be found under close inspection. The bezels will have good chrome with no obvious defects but the paint will need attention. This is a good saving over buying the four or six parts individually. Don't forget to pick up a set of gaskets for the lenses as they always are needed after 40 plus...

1968 XR7 and standard Cougars use the same rear wiring harness to the taillights. This is a grade "B" grade harness that may be spliced or repaired. XR7 and Standard Cougars use the same rear wiring harness to the taillights, only the sub-harness that connects to it that runs along the underside of the package tray and down to the fuel sending unit differs XR7 vs. Standard. The major difference is that the xr7 utilizes a two wire plug and the Standard Cougar uses a single wire. Harness begins...

100% complete assembly with near perfect chrome, tested socket, good used bulb and all hardware needed to install. Perfect choice for that all original low mile survivor that shows some patina. Mustang is different and the reproductions must be modified to work on the Cougar. 68 plugs differ from 67 plugs and whereas PS and DS look similar they are in fact side specific. New mounting pads and lens gaskets are sold separate.

100% complete assembly with near perfect chrome, tested socket, good used bulb and all hardware needed to install. Perfect choice for that all original low mile survivor that shows some patina. Mustang is different and the reproductions must be modified to work on the Cougar. 68 plugs differ from 67 plugs and whereas PS and DS look similar they are in fact side specific. New mounting pads and lens gaskets are sold separate.

New Old Stock turn signal switch for fixed steering columns on 1968-69 Mercury Cougar and Ford Mustang.Replaces Ford part # C8SZ-13341-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used upper wiring harness for the overhead console on the 67 - 68 Cougar XR7. Sometimes known as the Convenience Group Harness. This harness runs under the headliner from the overhead console back to the C pillar, where it connects to the lower harness. You can get the lower harness here. Ford Part Number C7WB-10C877-F

Emergency or parking brake indicator lamp and wiring harness. Tested and working red indicator light which was found optionally on any 1968 Mercury Cougar standard model 65A or 65C. The 1968 parking brake light kit gets its power from the ignition switch. 

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Used steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1970-72 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is black, there is also a natural or white color version of this plug used by Ford 1968-69. Ford part number D0AZ-14489-L.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

These amber colored bulbs are getting very hard to come by these days. Even the lesser quality painted amber bulbs have not been available from auto parts stores for over a decade now. If you search around you will see that some vendors retail these at over $5.00 each plus shipping! We have a limited supply of these bulbs, so you may want to get an extra pair. The 1968 Ford manuals call for a 97n bulb, but that is an error believe it or not. Sold individually and two are required per...

We have had so many dealers inquiring about these we are now offering dealers, and those who own multiple cars that use these rare bulbs, a quantity discount. We have witnessed these bulbs sell for as much as $9 each on ebay! The 1968 Ford Manuals call for a 97N bulb, but that is an error believe it or not. 

Ford sold service replacement taillights as a complete unit that included the backing, chrome and lens, just the lens or just the chrome. This listing is for one complete taillight unit as shown.Sold individually, two required per car. Ford part number C7WB-13440-A *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

Original OEM light found on early cars and later recalled. EXACTLY 100% correct with the right serial numbers in the right places as per the blueprints from Shelby American: * IGM 1642 PN on the bottom right * K11123 N14 cm AUF 5m up the right side * No numbers on left side Marchal made several versions of this light, only this one is the correct one for your Mustang. It has the famous 'cat eyes' internal diffuser. Reproduction lights use a different bulb, lack the diffuser and have the word...

New Old Stock NOS retainers for right and left front marker / parking lights for any 1967-68 Mercury Cougar or 1965-1968 Ford Mustang. These are driver and passenger side specific. Replaces Ford part # C5ZZ-13221-C*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, sold individually. Replaces Ford part # C5ZZ-13206-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

We really cannot justify the average guy buying these over our quality reproduction pair. Only the most tedious of restorations would benefit from having this levels of detail. Sold as a pair, Ford part #: C5ZZ-13206-B for the passenger side and C5ZZ-13207-B for the driver side.

Reproduction 4002 incandescent (non-halogen) low beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 3-prong plug and mounts in the outboard position on the car.These are close to OEM wattage (37.5 / 60 watt, OEM was 37.5 / 50 watt) to work with the factory headlight switch, without adding any relays like you would for higher wattage halogen bulbs.Ford Bulb #: 4002, Aftermarket Bulb #: 4000. Sold individually, 2 required per car. ...

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Used grade "B" rear courtesy / opera light lens for the Mercury Cougar. Opera lights were came as standard equipment on all XR7 Cougars, but were installed on many decor and standard level Cougar interiors. These units will have a few "warts" which show up as pitting in the chrome and may also have some minor cracking in the lens. If you just need a lens for your driver quality car, these are a great option. But if you compare this grade "B" lens to our reproductions, it will look like...

This used assembly includes lamp socket, bracket, mercury switch, and length of wire.Replaces part # C7ZB-15702-A

Used stamped nut for attaching the tail light bezels to the tail light housings. This is a 8-32 nut, with a 11/32" hex and is intended for the 8-32 threaded studs attached to the tail light bezels on any 1967-68 Mercury Cougar. Sold individually, 10 per side, or 20 per car.Replaces Ford part number 45203-S.

1967 - 1968 Mercury Cougar emergency light flasher relay. Good used, original, and 'tested' unit ready to plug in and use. Lead wire not included, shown in picture for help in identification purposes. Replaces Ford part number C7WB-10C838-B. The reason we gave this used item a crappy logo, is that they weren't designed to last over 50 years. The simple electronics they used back when they made these cars just weren't up to par with the quality of electronics designed today. We recommend...

Good used driver Quality, no cracks in lens and not pitted but will show "patina". Ford part #C8GY-13380

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

NOS, never been installed part they may or may not come with original box, will show shelf wear. Ford Engineering number stamped on the part is C8WB-11652-C.

Replacement turnsignal switch for all 1968 Mercury Cougar and Ford Mustang with fixed (non-tilt) steering columns. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to...

1968 XR7 and standard Cougars use the same rear wiring harness to the taillights. This is a grade "A" premium grade harness that is not sun damaged, spliced, or damaged in anyway. XR7 and Standard Cougars use the same rear wiring harness to the taillights, only the sub-harness that connects to it that runs along the underside of the package tray and down to the fuel sending unit differs XR7 vs. Standard. The major difference is that the xr7 utilizes a two wire plug and the Standard Cougar uses...

Emergency or parking brake indicator lamp and wiring assembly. Tested and working red indicator light which was found optionally on any 1968 Mercury Cougar standard model 65A or 65C. The 1968 parking brake light kit gets its power from an accessory plug coming from the fuse block. Ford part number C8WB-10A841-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price...

We shatter the castings from used back-up light assemblies to remove the socket and pigtail complete. This is for the person who has a nice original back up light and is willing to invest the time to repair a damaged pigtail. This light was also used on the 1965-1966 Ford Mustang.

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...