Heating & Air Conditioning

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, spring is available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19C784-A Register and Bezel. (Bright Finish). Ford casting number on reverse of this piece is C8ZA-19C784. Mustang used a shorter bracket, on the reverse you can see the witness line and...

This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember back in the day when we used to spend hundreds of dollars for "decent" used examples and or take a...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang that is a high quality replacement part at a reasonable price. However, these off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the...

Good used working original heater blower motor for 67 - 68 Mercury Cougar and Ford Mustang.  The reproduction off-shore units may or may not prove to be as good of value as these good used original FoMoCo motors.  Keep in mind our used units carry a one year warranty and the new off-shore motors only have a 30 day warranty.  Also know that the mounting plate is included for free just by asking on the used motors. We never use the reproductions here at WCCC.  This unit...

Used air compressor to intake manifold tubular steel bracket. Connects and supports the rear of the air compressor to the factory intake manifold. From what we can tell, there is no difference from 1967 to 1968 pieces.Ford part # C8ZZ-2889-A

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A

This set of brushes only fits the Eaton brand of air compressor clutch. These are exact reproductions made from the original tooling. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to this version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for core brushes with stamped Ford numbers. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

Heater door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater door allows air to pass over the heater core in the A/C box. This is the smallest door in the A/C box, and the one subject to the most damage from moisture. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

New A/C vent hose with cam locks for your Mercury Cougar or Ford Mustang equipped with factory A/C. This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Two required per car, sold as a pair.Ford part #: C7WY-19B680 or B5A-18556-C.

Concourse Correct 90 degree elbow that attaches to the intake manifold and provides proper clearance for the emission canister and air cleaner housing. Correct for all 1968 S code 390-4V, W code 427-4V and R code 428 Cobra Jet engines.

Used heater and air conditioning box for late 1967 and 1968 Mercury Cougar and Ford Mustangs. These are getting so hard to find without a broken drain cock or rust in the metal lips. The unit pictured here is typical of what you can expect when you buy out used complete box. Plan on repairing the drain cock or other minor cracks. All doors will be functional, we will promise the evaporator is good and we do promise the heater core will be bad. We have a few single halves if you need the half...

NOS Air conditioning belt tension pulley for Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968.  Ford part # C7AZ-8678-B. NOTE* Send in your old core for a credit toward the purchase of this NOS pulley. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. Check out this video

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. Check out this video

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

This valve is used on Mercury Cougars and Ford Mustangs equipped with factory A/C to stop the flow of warm coolant when A/C is on.This valve is functionally the same as the OEM, but has obvious cosmetic differences from the factory valve.Replaces Ford Part #: C7ZZ-18495-A.

Vacuum tested working hot water valve for Mercury Cougars and Ford Mustangs equipped with factory A/C. This valve stops the flow of warm coolant when the A/C is on and has the original cast brass valve with bracket and vacuum pod. We are unable to guarantee that the water seal is good. Ford part # C7ZZ-18495-A, casting number on vacuum valve C7ZA-18C310-A.