Heating & Air Conditioning

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...

Used extension or rod for the vacuum actuator for controlling the fresh air door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the right hand end, of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting...

Used extension or rod for the vacuum actuator for controlling the air restrictor door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the front of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18...

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a brass plunger. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to retain your mounting bracket...

Used vacuum switching manifold and electrical micro switch assembly from a 1969 to early mid 1972 Mercury Cougar and Ford Mustang. This is the all metal version vacuum distribution block. 1972 owners, please check your A/C controller to verify if you have or need the plastic version of this switch. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

Used Grade A Windshield Defroster Nozzle for any 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Grade A will be free from physical defects, may have a minor scuff or scratch.Replaces Ford part number C9ZZ-18490-B.

Used Grade B Windshield Defroster Nozzle for any 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Grade B will have a small crack or chip, or possibly a broken mounting tab.Replaces Ford part number C9ZZ-18490-B.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end. Replaces Ford Part #: C9ZB-19A885-B.

Reproduction A/C evaporator for the later production 1969 - 1970 Mercury Cougar and Ford Mustang. This later version of the evaporator has inlet and outlet tubes that run diagonally of the core as opposed to the early version where the tubes run horizontally.*Note - We have had numerous customers complain that these don't fit exactly like the originals. As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies...

There are 2 manufacturers of these hoses and many places will call them a "concours" hose. Neither manufacturer make an exact replica of the original sight glass hose. The finish of the hose does not match, but the most obvious difference is that the sight glass itself has a hexagon shape instead of a square shape. If you would prefer a good used original, give us a call, we can usually dig one up for you. Remember to remove your coupler between this hose and the dryer, it will be need...

Here is your concours correct A/C suction hose for your beloved Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

C9ZZ-18A318-C New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang.Tested and works perfectly. Has attached extension marked C9ZA-18A318-J.

For 1969 Mercury Cougars and Ford Mustangs with the 351W engine. Also 1970 Mercury Cougars and Ford Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-3/8", a clutch diameter of 5-3/16", and an overall thickness of 1-11/16 inches. Whew, say that 5 times fast!Ford part # C9AA-2981-D.

For 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch. Pulley diameter 6-3/4", clutch diameter 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-G.

This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...

Used mounting bracket from a 1969-70 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. Same bracket at 1967-68, but with a longer stud.

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A

This set of brushes only fits the Eaton brand of air compressor clutch. These are exact reproductions made from the original tooling. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to this version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for core brushes with stamped Ford numbers. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

Heater door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater door allows air to pass over the heater core in the A/C box. This is the smallest door in the A/C box, and the one subject to the most damage from moisture. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

C9ZA-18C366-A lower heater duct to floor outlet for Cougars or Mustangs without air conditioning. Used grade "B" part that will have more than one minor defect. It will have a small crack and possibly a broken or missing tab. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered.

Reproduction chrome heater hose elbow is for 351, 390, and 428CJ engines. Replaces Ford Part # D0AZ-18599-C Barbed End: 5/8" hose barbThreads: 1/2" NPT (Tapered Threads) For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Concourse correct 351 2bbl engine heater hose connector with a 90?� degree elbow that attaches to the intake manifold. Product discontinued by manufacturer. Know anyone else reproducing these? Let us know!

Concourse correct 90 degree heater hose elbow that attaches to the intake manifold and provides proper clearance for the emissions canister and air cleaner housing. Correct for all Boss 302 and 428CJ engines 1969-70.Ford number C9ZZ-18599-A.

For factory installed A/C on Mercury Cougars and Ford Mustangs. This unit functions great, but when compared to the NOS unit, you will see that it is cosmetically a little bit different. This uses the "O" ring style seals which are not included.Will work with both R12 and R134 systems.

Metal fan wheel or squirrel cage for any 1969-70 Mercury Cougar or Ford Mustang with heater only. Dimensions 4-3/4 inches in diameter and 2-1/2 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Reproduction grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Made from closed cell foam, as opposed to the originals being rubber.* Note - Used starting during the later part of 1969. Compare the evaporator line orientation for both years.

These are reproduction heater hose grommets for the heater hose to pass through the firewall. Most of the firewalls that we have seen have a flared opening for the hose without a grommet. These are a more dense rubber than our other versions. Still not sure that they are needed?

These are getting so hard to find without a broken drain cock or rust in the metal lips. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this assembly listed here, in the mean time give us a ring for those obscure parts! Two versions for 1969-70 Mercury Cougar and Ford Mustang. Difference is the evaporator and the orientation of the tubes. Look for the triangle shaped rubber line seal for the later 1969-70...

C9ZZ-18A651-B Complete heater and power ventilation system control assembly includes bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. The power ventilation system was a pretty rare option for 1969-70. It included a center dash register as found on air conditioned cars and directed cool air through the center of the dash. Dearborn cars would have a code "VS" on their body buck tags, and Metuchen...

Dual heater hose tube assembly for the 1970 Mercury Cougar and Ford Mustang with the 428 Cobra Jet or 428 Super Cobra Jet engine. This heater hose attaches along the top of the passenger side valve cover. Length of long end: 13 3/8" Length of short end: 8 5/8" Replaces Ford Part #: D0ZZ-18B402-A.

Cast iron pedestal mount for the air conditioning compressor on all 1970 Mercury Cougars and Ford Mustangs with the 351W H code 2V engine. Ford also used this bracket on other 1970-71 Ford passenger cars with 351W engines only.Ford casting number D0AA-2882-E.

Shaft or rod for the heater core damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-B.*Note will not work in 1967-68 A/C boxes. ...

This 1969-70 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390 / 428CJ's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

Here is our NOS vacuum valve assembly which is fairly hard to come by these days. This unit is for Mercury Cougars or Ford Mustangs with integral or factory air conditioning. This part is good until an assembly date of 1/3/1972 and, if you want, we also have good used pieces in stock for your Coug or Stang as well. Ford part # C9ZZ-19B888-A.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

windshield defroster nozzle to vent for any 1969 - 1970 Cougars or Mustangs without air conditioning. This used grade "B" part will have more than one minor defect. It will have a small crack and possibly a broken or missing tab, but it's a heck of a lot better than wiping your windshield with your sleeve.Replaces Ford part number C9ZA-18490-A.

C9ZA-18490-A, windshield defroster nozzle to vent for any 1969 - 1970 Cougars or Mustangs without air conditioning. This part is used and is grade "A."  If it does have any minor defects, it will have only one. It might have a small crack, but will not have any broken or missing tabs. If you drive your baby when it is cold and don't have this part, you want it. Why, because it's lame when you have to use your sleeve to wipe off your windshield to see where you are going. It's also a heck...