Fuel

Great little kit that is a big time saver! Correct in detail, every 40 year old Cougar needs this kit! Replaces Ford Part #: C5ZZ-9A702-MK.

Correct texture Gas Pedal, includes stainless steel trim.

Black moulded plastic pedal pad for all 1967 and 1968 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C5ZZ-9735-A.

Correct spring, black phosphorus plated. Does not have the same tension as original spring. We also have a Concours spring that has the correct tension. Replaces Ford Part #: C5ZZ-9737-B.*Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with 289 or 302 engines. Ford part number C8ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. Ford part number C8WY-9A702-A *Note - Before 12/11/1968. *Note - not for use with factory cruise control.

Concours Correct Throttle Linkage Rod, 13 1/2" long, S code 390-4V, W code 427-4V, and R code 428CJ with factory 4 barrel HOLLEY carburetor, with out speed control.Replaces Ford Part # C8ZZ-9A702-A

Clip for mounting the throttle linkage rod rod to the carburetor and mounts C-4 or C-6 throttle cables to the throttle bell cranks.Replaces Ford part number C2VY-9826-A.

Over 100 total vacuum caps in 6 different sizes.

Reproduction vacuum fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All brass fitting, goes into the passenger side of the carburetor for the vacuum advance. This should be ported vacuum.Ford part number 358165-S.

1968 390-2V Autolite 2100 carburetor, automatic C6 transmission - All 50 states. C8WF-A stamped on the carburetor base. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. X code engine 390-2V premium fuel. *Trivia every single X code 390-2V Cougar was an automatic, no manual transmissions what so ever.

1968 302-4V Autolite 4300 carburetor, Canada DSO's - Open Emissions. C8ZF-B stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. Not sure if this is for stick or automatic transmissions, Notice the unique color on the tag? 

1968 390-4V Holley 4150 carburetor, 3 or 4 speed manual transmission - all 50 states. C8OF-9510-C stamped on the carburetor air horn. Holley list #3795, 600 cfm. Core carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top, transfer tube or good choke assembly on our cores.

1968 428CJ-4V Holley 4150 carburetor, 3 or 4 speed manual transmission - all 50 states. C8OF-9510-AA stamped on the carburetor air horn. Holley list #4174, 735 cfm. Core carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top, transfer tube or good choke assembly on our cores.

1968 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - All 50 states. C8OF-9510-AB stamped on the carburetor air horn. Holley list #4168, 735 cfm. Core carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top, transfer tube or good choke assembly on our cores.

CARBURETOR SPACER PLATE, 0.28" thick, has correct tab marked "FRONT". Replaces Ford Part Number C8AZ-9A589-G

Factory two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Unique to the X code 390-2V premium fuel engines.

Clevis type attaching clip for attaching the accelerator throttle rod to the carburetor on all 1967 and 1968 Cougars. The correct installation is with the clip pushed on from the top, barbs down. This is the right handed style.Original Ford part number C2VY-9826-A

Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

This is the OE steel tube that goes from the Ford Holley carburetor to the Carter X fuel pump. This was copied to fit the vintage Ford Holley 4150 carburetors as originally found on 1968 390-4V, and 1968-70 428CJ engines. *Note - Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps. **Note - Excludes 1969 390-4V with...

Reproduction fuel bowl fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All steel fitting, two needed per carburetor. Sold individually. Check the threads in those Holley bowls prior to installation, often times the bowls are bad.

Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.

Nice rebuildable core of the Carter X 4441S fuel pump for all 1968-70 428 Cobra Jet engines. Has "X" casting, 4441S stamped, dated 10B9A, February 10, 1969. Kits available for rebuilding. 

Factory original Carter fuel pump that was taken from a low mile 427 GTE in 1997. The "X" pump was used only on the Boss 302, 427, 428 and 429 Cobra Jet, and Super Cobra Jet.

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1968 Mercury Standard model Cougars and all Ford Mustangs with 16 gallon fuel tanks. This is an original 1968 fuel sending unit with one electrical prong. Ford casting number C8ZF-9275-A, master parts catalog number C8ZZ-9275-C. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models or Ford Mustang with low fuel warning...

Premium reproduction fuel / gas tank for the Mercury Cougar or Ford Mustang. 16 gallon capacity, correct in every way including the drain cock.Replaces Ford part # C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar! ...

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970.  Ford part # C9AZ-9H576-A.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.

Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *Note - This bracket is a bit longer than the 2V version.

"L" shaped bracket that mounts to the rear of the Holley carburetor mounting hole for attaching the return spring. Bracket faces forward when installed.

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: c5zz-9a702

Neat detail item, stamped steel with zinc plating. Mounts on intake manifold and holds one end of the accelerator linkage spring for the 289 / 302.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Application 1968 Mercury Cougar and Ford Mustang  with 289 or 302 engines and cruise or speed control. Ford part number C8ZZ-9A702-C. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with X-code 390-2V engines and speed or cruise control option. Original Ford part number C8WY-9A702-B. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - For use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.96 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with S or R code engines. Ford part number C8ZZ-9A702-B. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 13.54 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. Application is 1968 Mercury Cougar and Ford Mustang with 390-4V or 428CJ engines and speed or cruise control. Original Ford part number C8ZZ-9A702-D.*Note - For use with factory cruise control.