Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1-48 of 136
$0 Price: $9.77

Buy Details

Availability: Out of Stock
Item #: 16000 -

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

$0 Price: $31.85

Buy Details

Availability: In-Stock Item
Item #: 23969 -

Reproduction concours correct throttle return spring bracket for the Mercury Cougar or Ford Mustang equipped with the 390GT engine. This bracket is shorter in length than the 390-4V piece.Ford part number C7OZ-9741-B.Also good for 1968-1/2 - 428CJ.

$0 Price: $67.35

Buy Details

Availability: In-Stock Item
Item #: 41050 -

Fuel and brake line fastener kit. Fits all 1967 Mercury Cougar and Ford Mustang with V-8 engines and 2 piece fuel line from tank to pump. Early production 1967 cars used a 1 piece fuel line from the gas tank to fuel pump. Eventually Ford installed 2 piece fuel lines during 1967. This is only for the two piece fuel line.*Note these are for the original and reproduction style fuel lines that were 5/16 thick, which was unique to 1967 production.

$0 Price: $44.55

Buy Details

Availability: In-Stock Item
Item #: 41049 -

Fuel and brake line fastener kit. Fits all 1967 Mercury Cougar and Ford Mustang with V-8 engines and 1 piece fuel line from tank to pump. Early production 1967 cars used a 1 piece fuel line from the gas tank to fuel pump. Eventually Ford installed 2 piece fuel lines during 1967. *Note these are for the original and reproduction style fuel lines that were 5/16 thick, which was unique to 1967 production.

MSRP:$10.00
$10.00 Price: $5.55

Buy Details

Availability: In-Stock Item
Item #: 30513 -

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

MSRP:$10.00
$10.00 Price: $8.55

Buy Details

Availability: In-Stock Item
Item #: 14258 -

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The problem with these brass floats, is that after year of being in contact with fuel, they will begin to corrode and disintegrate. We suggest going with the new foam floats. They are fuel resistant and will last longer. Find it here. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

$0 Price: $594.77

Buy Details

Availability: In-Stock Item
Item #: 32111 -

Reproduction polished aluminum 600 CFM "Street Warrior" carburetor for the 67 - 73 Cougar or Mustang. Replaces Holley, Edelbrock, Carter AFB, and Autolite style carburetors with 5 3/16" x 5 5/8" bolt pattern. Performance upgrade for stock to mildly modified V-8 enginesCalibrated for excellent street performance right out of the boxFactory preset electric choke for easy startupsVacuum secondaries for use on wide variety of vehicles. Compensate for all vehicle weights, gearing &...

$0 Price: $304.97

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24024 -

1967 289-4V Autolite 4300 carburetor, Automatic C4 transmission- 49 states. C7DF-AF stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engine. *Note not for DSO 52 and DSO 53 California destined cars.

$0 Price: $193.86

Buy Details

Availability: Out of Stock
Item #: 24035 -

1967 289-4V Autolite 4300 carburetor, Automatic C4 transmission- California  C7DF-D or  C7DF-AH stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engines with automatic transmissions. *Note - For DSO 52 and DSO 53 California destined cars. ...

$0 Price: $341.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24059 -

1967 390-4V Holley 4150 carburetor, automatic C6 transmission - 49 states. C70F-9510-B stamped on the carburetor air horn, Holley list #3794, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V and 390GT engines with automatic transmissions. *Note not for DSO 52 and DSO 53 California destined cars.

$0 Price: $386.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24058 -

1967 390-4V Holley 4150 carburetor, 3 or 4 speed manual transmission - 49 states. C70F-9510-A stamped on the carburetor air horn, Holley list #3793, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V or 390GT engines manual transmissions.. *Note not for DSO 52 and DSO 53 California destined cars.

$0 Price: $550.85

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 33575 -

New Street Avenger carburetor. The 350 CFM Street Avenger carburetor has great features such as optimized street calibrations...two vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters; and an included 3/8" fuel line connection so there are no unnecessary trips back to the parts store. Known to bolt in right out of the box. The Avenger series are the first carburetors to have a limited lifetime warranty. With a great...

$0 Price: $40.25

Buy Details

Availability: In-Stock Item
Item #: 10482 -

Basic kit for rebuilding your Ford Autolite or Motorcraft 2100 or 2 barrel carburetor. Covers all factory 2 barrel carburetors on any 1967-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 2100 carburetors. Excludes later 2150 carburetors.

$0 Price: $32.75

Buy Details

Availability: In-Stock Item
Item #: 18906 -

Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered Rochester Quadrajet carburetors in 1970-71. Sold as a PAIR.

$0 Price: $29.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23814 -

Factory cast aluminum two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Fits all Ford 2 barrel carburetors, bore size is 1-5/8 inches in diameter. ...

$0 Price: $81.85

Buy Details

Availability: In-Stock Item
Item #: 11231 -

Nice quality reproduction of the bake-o-lite carburetor spacer plate for all 1966-67 S-code 390-4V engines. Measures 0.28" thick, with small vacuum hose nipple on rear replaces Ford Part Number C6AZ-9A589-B. Fits 67 Cougar 390 Fits 67 Mustang 390 Fits 66 Fairlane 390 Fits 67 Fairlane 390 Fits 66 Cyclone 390 Fits 67 Cyclone 390 Check out this video ...

$0 Price: $128.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23928 -

Measures 0.28" thick, with small vacuum hose nipple on rear Ford Part Number C6AZ-9A589-B. Mint condition original part.

$0 Price: $50.95

Buy Details

Availability: In-Stock Item
Item #: 41875 -

Good Quality spacer that measures 1 1/8" tall. Comes with PCV hose clamp and vacuum port cap. This was used on all 289, 302, 351w motors with a 4V carburetor.

$0 Price: $60.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23830 -

Factory cast aluminum four barrel carburetor spacer plate, 1-1/8" tall. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. *excludes Boss 302 Eliminator ...

$0 Price: $2.15

Buy Details

Availability: In-Stock Item
Item #: 11811 -

New 390 2BBL Carburetor spacer gasket for the 1968 X code 390-2V engine. Two needed per installation, one on both sides of the spacer plate.

$0 Price: $5.82

Buy Details

Availability: In-Stock Item
Item #: 15292 -

New carburetor gasket for 67 - 70 Cougar or Mustang with 390 or 428 cobra jet engines and Ford numbered Holley carburetors. One or two needed per installation (with or without spacer plate) sold individually.

$0 Price: $5.95

Buy Details

Availability: In-Stock Item
Item #: 19973 -

New carburetor gasket for all 289-4V, 302-4V, and 351-4V, Mercury and Ford cars from 1964-1970. Same gasket used between intake manifold and spacer, and spacer and carburetor. Sold individually, 2 required for complete installation with Ford 1 inch factory spacer and correct numbered Autolite 4300 carburetors.

$0 Price: $125.00

Buy Details

Availability: Out of Stock
Item #: 33521 -

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4193S. This is the early style with "CAR bure TER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with A or C code 289 engines and 1966-67 Ford and Mustang with A or C code 289 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and...

$0 Price: $125.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33573 -

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4193S. This is the late style with "CARTER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with A or C code 289 engines and 1966-67 Ford and Mustang with A or C code 289 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...

$0 Price: $155.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33522 -

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4194S. This is the early style with "CAR bure TER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with S code 390 engines and 1966-67 Ford or Mercury with S code 390-4V V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...

$0 Price: $155.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33574 -

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4194S. This is the late style with "CARTER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with S code 390 engines and 1966-67 Ford or Mercury with S code 390-4V V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible dates, we...

$0 Price: $24.85

Buy Details

Availability: In-Stock Item
Item #: 32356 -

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

$0 Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 41464 -

Reproduction 8 Cylinder 2V Choke Thermostat Shield for the 1967 and 1968 Mercury Cougar and Ford Mustang

$0 Price: $5.55

Buy Details

Availability: In-Stock Item
Item #: 14204 -

Slightly longer than the original. Replaceable filters which attaches to original fuel sending unit. Only fits the 1967 Mercury Cougar. Replaces Ford part #: D1FZ-9A011-A.Check out the video below on our new gauge tester: ...

$0 Price: $75.02

Buy Details

Availability: Out of Stock
Item #: 13693 -

Used factory installed vented fuel, or gas cap as installed on 1967-69 Mercury Cougar 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap.We stock these in limited quantities, and will have an intact paper gasket. Correct "VENTED" embossed and has the "S" stamped onto the center rivet. Price is established by demand, and these normally are only needed for very high level restorations or strict concours judging...

$0 Price: $194.85

Buy Details

Availability: Rare / NOS Part
Item #: 33148 -

This filter ONLY fits the following 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19.

$0 Price: $18.05

Buy Details

Availability: In-Stock Item
Item #: 41436 -

This filter ONLY fits the following Ford Holley 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. This is a service replacement filter, it has D2AE-9155-AA stamped on the body of the filter. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19 and C9AZ-9155-B,  FG-39.

$0 Price: $30.69

Buy Details

Availability: In-Stock Item
Item #: 33629 -

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

$0 Price: $8.15

Buy Details

Availability: In-Stock Item
Item #: 11802 -

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

$0 Price: $20.91

Buy Details

Availability: In-Stock Item
Item #: 41857 -

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar

$0 Price: $40.65

Buy Details

Availability: In-Stock Item
Item #: 31551 -

This is the steel tube that goes from the carburetor to the fuel pump. Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps.

$0 Price: $39.55

Buy Details

Availability: In-Stock Item
Item #: 14030 -

This is the steel tube that goes from the carburetor to the fuel pump if you have a 289 or 302, and you have the Autolite 4300 4 Barrel Carburetor. Stainless Steel.

$0 Price: $36.55

Buy Details

Availability: In-Stock Item
Item #: 11761 -

Reproduction fuel line that goes from the fuel pump to the carburetor made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 390-4V engine. Fits all FE engines with Holley 4150, as long as they do not have the Carter "X" fuel pump. Carter X fuel pumps are not crimped together.

$0 Price: $25.67

Buy Details

Availability: In-Stock Item
Item #: 14008 -

This is the steel tube that goes from the carburetor to the fuel pump. Designed for vehicles LO-VOL fuel pump, fits 67 - 70 Mustang, 67 Cougar 390, 67 Fairlane and Torino.

$0 Price: $56.42

Buy Details

Availability: Out of Stock
Item #: 12439 -

Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.

$0 Price: $191.85

Buy Details

Availability: In-Stock Item
Item #: 11354 -

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 427 or 428 engine. Updated design from the originals, fuel lines fit the same.

  • < Prev