Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Stud for attaching exhaust manifold heat shield on 1969 Mercury Cougar or Ford Mustang with 351W. Sold individually. Replaces Ford Part # 382592-S
New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.
New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.
Sold individually Zinc (dark silver)
1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16
Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.
This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S
Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.
Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.
Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.
Sold individually, phosphate & Oil (gray-black).
A nice reproduction of the standard air cleaner wing nut. This version was used on most Ford products through the 1980's.
Master clip kit which includes following fasteners:Door courtesy and speaker Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorn feedPassenger side apron below relayRadio cable to dashSide marker and headlightsTurn signal lights on hood scoopUnder dashVarious location zip tiesKeep in mind that there are many other fasteners on 1969 Cougars / Mustangs that are not in this kit. ...
Complete 25 piece clip kit for the 1969 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.
3/8-16 X 1 3/8" Grade 5 Uniform Bearing Stress (UBS) Flanged Bolt. Replaces Ford Part #: 56341-S2
Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually.
Includes battery clamp and bolts required to mount battery on tray. Please note that vinyl coating will almost always crack along edges shortly after installation.
Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.
Used plastic clip for the Mercury Cougar or Ford Mustang.
Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.
Used Under-dash Wiring Harness Plastic Cover / Clip for the 1969 and 1970 Mercury Cougar or Ford Mustang
Fits 1968 - 1973 Standard or XR7
New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.
This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...
This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...
This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A
Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.
This clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.C8AZ-2B277-A
Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.
Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.
24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Also sold individually.
Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...
If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...
Used seat belt bolt washer for the Mercury or Ford.
Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.