Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)
Replaces Ford Part # 381985-S Sold individually
Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.
Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.
This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Replaces Ford part # C2DZ-6A529 Sold Individually.
Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut.
Perfect fit.
New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S
Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.
New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...
Four needed per fan shroud. Sold individually.Ford Part Number: 383152-S
These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.
Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...
Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...
Replaces Ford Part # C8AZ-2066-A Sold individually
This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Two required per car. Replaces Ford part # D1ZZ-6522244. Sold individually
Reproduction roofrail weatherstrip seal clip and quarter window guide clip for the 1971, 1972 and 1973 Mercury Cougar or Ford MustangFord Part #: D1ZZ-6522204
Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...
Sold individually. Zinc (dark silver)
Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Sold individually. 24 required per car, set of 24 also available. ...
Used unique Phillips bright finish screw that attaches cable guides to roof.
One size fits all. Set of 4. Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S
These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.
Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)
This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...
Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...
Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...
Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.
8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S
Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...
Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...
Fits 1967 - 1973 Standard or XR7. Pins not used on 71-73 buckets.
This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...
If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...
Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.
One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.
Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.
Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.
This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292
This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...
These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individually
Sold individually. Zinc Dichromate (yellow-rainbow)
Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.
Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K
replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish