Electrical & Lighting

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

C9WY-14018-B Left side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

C9WY-14018-A Right side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7 Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

C9ZZ-18578-A mounts to the rear of the factory installed heater control ventilation control pane. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1969-73 selector button kit. LINK This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

This used intermittent wiper switch has a two speed wiper function, and when turned counter clockwise, has a rheostat that sets the different delay times. A 1969 switch can be used, but the shaft will be about 3/8" shorter, you may need to use a 1969 metal knob to use in a 1970. Sometimes called interval or delay wipers.*NOTE* Must be used in conjunction with a Intermittent wiper controller.Replaces part # D0ZF-17A553-B, MPC # D0ZZ-17A553-A

Tested and inspected neutral safety switch for the C-6 transmission installed in 69-70 Mercury Cougar and Ford Mustangs. This neutral safety switch is identified by having a single plug, Identified with a single plug with weatherproof seal, the earlier versions do not.Look for a transmission code of U on your door data plate. If your car has a code W, your original transmission was an C-4 and uses a different neutral safety switch.Replaces Ford Part #: C9ZP-7A247. ...

New Old Stock neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug that will not be utilized when used on a 69 - 71. Ford part #: D2ZZ-7A247-B, SW 903B Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked...

Reproduction power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch.However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

NOS fixed column turn signal switch for the 1970 Mercury Cougar or Ford Mustang. Ford part number D0ZZ-13341-A or D0ZA-13B302-C. Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Tested and working emergency or parking brake indicator switch. Foot parking brake switch found on 1969-70 Mercury Cougar and Mustang with visibility group option. Includes bolt to attach to emergency foot brake. Ford part number: C6GB-15652-A

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

Reproduction Temp Sender Switch with Warning Lights for the 1970, 1971, 1972 and 1973 Ford Mustang with a 351

Reproduction oil pressure remote sending unit tube assembly. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge.The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell shaped oil...

Used shutoff valve for the headlight vacuum system of all 1969-70 Mercury Cougars. Also found on 1969-70 Ford and Mercury full sized cars with hidden headlights. Additionally these were also used on 1969-70 midsized Ford and Mercury such as Torino, Cyclone, also with hide away headlamps. This is a black plastic shutoff switch or connector, 1969 cars used a white valve that crumbled from the under hood heat. Note that the indicator tabs perpendicular to the lines means 'open'. Turning the valve...

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets. These were used on 1970 cars starting approximately 9/15/1969 on Non-Air cars, and some A/C cars. Some A/C cars came with one for the 68 A/C Voltage Regulator.Replaces Ford part number D0AF-10316-A (cover only)

Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

New reproduction instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Features Solid State electronic circuitry. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator...

Features the proper cover and original logos. I A S F stamped on cover. These were used on 1970 cars starting approximately 9/15/1969 on Non-Air cars, and some A/C cars. Some A/C cars came with the 68 A/C Voltage Regulator. Replaces Ford Part #: D0AF-10316-A. The voltage regulators listed in this section are poor quality. We suggest you buy a reliable, modern, solid state unit and just use the cover we sell as a stand alone product. We will not warranty the mechanical voltage regulators you...

Voltage regulator for the 1968, 1969, and 1970 manufactured before 9/15/1969 that is not equipped with factory AC. This regulator has "C8AF-10316-A" printed on to it, actual Ford Part number is C3SZ-10316-B or D4TZ-10316-A. This is Ford Regulator Number GR-341. These new voltage regulators are improved and more reliable than the units we've sold previously.

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets.Replaces Ford part number C8AF-10316-A (cover only)

Reproduction Dash to Gauge Feed Harness for the 1970 Mercury Cougar and Ford Mustang with either the 351C-2V or 351C-4V, Cleveland engine only. Replaces Ford Part #: D0ZZ-14289-ACheck out the video below on our new gauge tester: ...

Big Block FE 390 or 428 engine feed harness that fits the 1969 or 1970 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C9ZZ-14289-B and D0AZ-14289-A.Check out the video below on our new gauge tester: ...

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black and yellow boot plugs, this is the style used on cars without air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end. Replaces Ford Part #: C9ZB-19A885-B.

Wire harness extension that runs from the under dash harness to the A/C fan control switch on any 69 - 70 Cougar Standard or XR7, or the 69 - 70 Mustang.Ford part number C9ZA-19945-B

Preproduction wiring harness, connects the convertible top switch to the pump on both the xr7 and standard model Cougars and Mustang 1969 - 1973 convertibles.

This harness connects the convertible top switch to the pump on both the xr7 and standard 1969 - 1973 convertibles.

Main wiring harness for consoles on 1970 Mercury Cougar and Ford Mustangs. Short harness more of a jumper wire for the ashtray illumination light. Ashtray wiring socket assembly sold separately.Replaces Ford part # D0ZB-14A012-B.

Reproduction dash to console harness for your 69 - 70 Cougar or Mustang.

Grade "A" harness that runs from the passenger side door jamb to the courtesy / C-Pillar light. This harness is only needed if you have a Standard model car. NOTE: All XR7's would have already come equipped with his harness.

For AM radio optional rear speaker. Ford part number C9ZB-18A900-BOverall length: 11' 7"

Factory used and tested under dash wiring harness for all 1968 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This harness plugs into the speaker plug of the radio, and connects the kick panel speakers in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door wiring harness that has the speaker plug for the door mounted speakers in 1969-70 cars. White speaker wire goes to the passenger side speaker, and the orange colored wire...

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Original used AM radio speaker lead wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustangs with factory AM radios. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios

Original used speaker lead wiring harness pigtail for all 69 - 70 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the door.*Note - The only difference between this pigtail and the one listed for the 1967-68 dash speaker is the actual plug design.

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Original used AM radio power lead wiring harness pigtail for the 67 - 71 Mercury Cougar and Ford Mustangs with factory AM radios. This double male plugged wiring pigtail solders to the your factory Ford AM radio. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your radio. Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door...

Used turn signal wiring pigtail for the 69 - 70 Cougar or Mustang. Pigtail is from the switch side of the turn signal.