Electrical & Lighting

[No Description Provided]

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Reproduction oil pressure remote sending unit tube assembly mounting kit.. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge. The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: ...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 back up light bulb for your 69-70 Cougar or Mustang. (67-68 and 71-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175) These Plasma LED bulbs will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1157 WHITE LED Plasma stop lamp / turn signal light bulb for your 67 - 73 Cougar, Mustang or anything else you might have that takes a white 1157 bulb. Please note that these bulbs are ground sensitive. Did you know that white (clear) 1157 bulbs fit a ton of other cars and trailers from the 50's clear through the 90's and beyond that used the...

This plug will work on your 69 - 73 Standard or XR7 as well as the 69 - 73 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction master power window switch that goes along with the power window conversion kits. Keep in mind we will buy your old usable factory parts. You might be surprised what those left over clips and wiring harnesses are worth!  Installing this master switch allows you to keep the original look of the crank handles, but allows the driver to control all four windows. All wiring and connectors are included.  ...

This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Used cast dual sheave alternator pulley. Casting number C9AF-10A352-C, we believe that these originally had a zinc dichromate finish. Called out for use on various 1969-70 Mercury Cougar and Ford Mustang with a need for a dual sheave alternator pulley.*Note - this is a cast pulley instead of the common stamped steel single sheave version.Ford part # C5AZ-10344-L.

Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction black extruded plastic shield, or rain gutter for the voltage regulator on any 1969-70 Mercury Cougar or Ford Mustang. Replaces Ford part number C9ZZ-10A506-A.

Used black extruded plastic shield, or rain gutter for the voltage regulator on any 1969-70 Mercury Cougar or Ford Mustang. Ford part number C9ZZ-10A506-A.

Rear defog conversion kit for most 1969-70 Mercury Cougar and all 1969-70 Ford Mustang Coupes. Includes hang down switch with wiring, long harness to blower motor, and blower motor and grille cover which installs in the rear package tray. Please see your electrical schematic for connection details. Excludes 1970 XR7 models, those cars had the defog switch integrated into the XR7 switch panel. This set up can easily be installed into a 1969 XR7 as well. You may need to purchase an accessory...

Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1970 Standard model Mercury Cougars (XR7 models use a different relay/bracket) and 1970 Ford Mustang with convenience option. Additionally fits 1970 full size and mid sized Ford and Mercury cars with headlights on reminder option. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D0AB-10C838-A or D0AZ-10C838-A. ...

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

This reproduction power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid. This relay can also be used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.Will replace D1AZ-14677-A, AND C1AF-14677-A but will not be an exact fit

Used seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1 or Ford Service part number D1AZ-10B924-A

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. Ford part numbers: DOZZ-17C491-A, D0ZB-17C491-A.

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

If your original is pitted or has come apart this will easily snap in place to remedy the problem. The finish on the repro differs a little from original.

Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Big bell shaped oil pressure sending unit for 1967 Mercury XR7 and 1967 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the 'nail head' connector. Please check your wiring harness for the proper connector.Replaced Ford part # C7ZA-9275-B Check out the video below on our new gauge tester: ...

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

Used windshield wiper motor cover or shield as Ford called it. Very prone to cracking and 'chalky' from age or UV light. We are not going to lie, most of these will have paint over spray or a slight amount of chalkiness. We haven't found a Ford part number other than the basic number of 17C441 which is labeled as "Shield - (Windshield Wiper Motor - Water)" as found in the Mercury MPC.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Not sure of the exact application for these original Ford stereo speaker wiring harnesses. We think that they may have come from the radio kits installed by Ford and Mercury dealers. Note the special speaker connector plugs. The individual right and left speaker wiring leads are about 40 inches in length from the center plug that goes to the radio or stereo. The paper tags are missing from these harnesses, but we are pretty sure that they begin with C8OA-19A041.One of our customers says that...

Reproduction mounting studs for the side marker light lenses on 1970 Cougars and Mustangs. 2 required per light, 8 per car.Sold as a pair.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.