Electrical & Lighting

Used service replacement switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and chrome knob, bezel is marked "DEFOG" as shown. *Note - this is not the OEM 1968 defog switch, it is the switch used in defog kits starting in 1970 for many Ford and Mercury dealer installed or over the counter kits.Replaces Ford...

Used switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and black knob marked "DEFOG". Replaces Ford part number C8ZZ-18578-A.

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITH a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The difference in the harness from the 67 to the 68 was different colored wires and different plugs. Replacement bulbs can be found on our site as well. ...

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITHOUT a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The only difference in the harness from the 67 to the 68 was different colored wires.

Used Distributor / 289-2V / 302-2V / Automatic Transmission for the 1968 Mercury Cougar / 1968 Ford MustangFord part number C8OF-12127-C  

Used Distributor / 302-2V / Manual Transmission for the 1968 Mercury Cougar / 1968 Ford MustangFord part number C8AF-12127-E  

1968 Mercury Cougar and Ford Mustang J code 302-4V with automatic transmission.Ford part number C8ZF-12127-D.

C8WF-12127-B distributor for use on 1968 Mercury Cougar and Ford Mustang with X code 390-2V engines and automatic transmissions. May or may not have a correct or working vacuum advance attached. Two remaining in stock, dates are: 8D1, 7M27.

Used Autolite Distributor for 1968 390-4V and 1968-69 428CJ for the Mercury Cougar, Cyclone or Ford Mustang, Torino.  Ford part number  C8OF-12127-D.  

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has two pressed in brass fittings for vacuum hoses. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1970 vacuum advance, the earlier vacuum advances had one of the vacuum fittings that screwed...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Reproduction single port vacuum advance for most all 1967-71 Ford V-8 engines. Fits Ford's brand of Autolite and Motorcraft distributors found on all 1967-71 Mercury Cougar and V-8 Ford Mustangs.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #107 or DF-342, single points cam with weights marked 13L and 18L from the top. Factory used on small block and FE distributors.  Ford part number C5AZ-12210-A.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #108 or DF-343, single points cam with weights marked 10L and 15L from the top. Factory used on small block and FE distributors.   Ford part number C5AZ-12210-B.

C8AF-12A022-A For all 1967 - 71 V-8 distributors. Concours correct head stamping. Brass plug for the stock Autolite distributors. Installs as shown.

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Many 70 - 73 cars used 3 pin type switches for the optional automatic seatback release feature. Sold individually. Additionally, this switch for the 3/4 inch mounting hole was used on 1968-70 Full sized Ford such as Custom, 500, Galaxie, LTD, and XL models, full sized Mercury such as Monterey, Montclair, Marquis, and Park...

Dual points conversion kit for all Ford V8 distributors. Big block and small block, parts included shown in pictures. Ford part number D0AZ-12A132-B.

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

Used electrical contact kit for the foot operated electric wiper actuating device. Most times these contacts have been fried, so instead of replacing the whole pedal you can now replace the electrical portion of the pedal and get it back to working condition.

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

Contains nut and washer. Fits all Ford alternators. AMK F-644.

New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.

C7ZB-17664-A Foot operated electric wiper actuating device for engaging the windshield washer pump or to cycle your windshield wipers once manually in light rain. Ford MPC number C7ZZ-17664-A. For any 1967 - 1968 Mercury Cougar and Ford Mustang.NOTE: If your electrical points are fried, you can simply replace them with the used contact replacement kit. Please note the Core deposit ...

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

C6OZ-14A068-A Black Bake-O-Lite original fuse block. Grade A, no cracks or chips. Perfect for upgrading your broken fuse block that has a nice wiring harness. 67 68 Mercury Cougar Ford Mustang, additional application are 1966-67 Ford Fairlane, Ranchero, Mercury Comet fuse panel.

C6OZ-14A068-GRADEB Black Bake-O-Lite original fuse block. Grade B, not broken, but will have chips from prying out fuses. Perfect for upgrading your broken fuse block that has a nice wiring harness. 67 68 Mercury Cougar Ford Mustang, additional application is 1966-67 Ford Fairlane, Ranchero, Mercury Comet fuse panel.

This is actually the correct 2 inch screw for the 1968, as opposed to the 1 3/4 inch screw that would have come in the 67. With the added length this screw is less likely to pull out of the firewall than the 67 screw was. Fits Standard and XR7. Sold individually.

New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.

New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

1967-1968 15 amp Buss style glass tube fuses sold in a package of 5 and used for the turn signals. This fuse is not located in the fuse box, but rather in an in-line fuse holder coming off of the turn signal switch on the steering column about 2.5 inches down after the plug.

1967-1970 7.5 amp Buss style glass tube fuses sold in a package of 5 and used for courtesy, glove box, luggage compartment, clock, tachometer, and radio pilot lights. Fuse length 7/8"

Used firewall grommet which your under hood harness runs through. This grommet is the same for Standard and XR7.

Used factory ground wire for the windshield wiper motor on any 1968 Mercury Cougar or Ford Mustang. Bullet connector plug and ground loop that mounts to bracket. Marked C8ZB-19C661-A.

Reproduction radio to door harness for your 67 - 70 Cougar or Mustang.

Headlight relay kit converts the 1967-68 Mercury Cougars with quad or 4 headlights to modern car technology (kit also works on 1967-68 Mustang 2 headlight systems). If your Cougar suffers from dim headlights you are not getting a full battery power to the back of your headlamp bulbs. Safe for use on our vintage cars. Still uses your headlight switch. Instead of carrying reduced voltage to the headlights through the switch, the switch triggers the relay, which takes power directly from the...

Headlight relay kit converts the 1967-68 Mercury Cougars with quad or 4 headlights to modern car technology (kit also works on 67-68 Mustangs 2 headlight system). If your Cougar suffers from dim headlights you are not getting a full battery power to the back of your headlamp bulbs. Safe for use on our vintage cats. Still uses your headlight switch. Instead of carrying reduced voltage to the headlights through the switch, the switch triggers the relay, which takes power directly from the...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness. NOTE: From the factory, Ford made the alignment tabs different passenger vs...

Reproduction replacement hold down clamp for the distributor on any 67 - 73 Cougar or Mustang. Sold individually, 2 needed per car.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

Nice lower quality ignition coil for those of you on a tighter budget. A wee bit cheaper than the other performance coils we offer like the Yellow Top Coil or the Pertronix Flamethrower series coils, but still a great buy and very reliable.   

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

NOS new old stock ignition lock cylinder for any 1967-69 Mercury Cougar or Ford Mustang.  Ford Motorcraft part # C9AZ-11582-A Here is a helpful "How To" youtube video on how to replace your ignition switch.

Made by the original supplier! Replaces Ford part # C9AZ-11582-A Here is a helpful "How To" youtube video on how to replace your ignition switch.