Decals & Emblems

Replaces Ford Part #: C8WB-17093-E. Notice this shows a crude line drawing of a Mustang but in fact carries a Cougar part number. This is the decal seen on most 1968 Cougars but many have a 1967 Mustang part number.

These are our 2-inch diameter round decals to customize the plastic Legendary Wheel Co. center caps that come with their wheels. These caps are also available separately, see item # 30529. Nice quality vinyl that will last outdoors, and the graphics have a mirror finish to compliment the chrome. *If you're buying a set of Legendary Wheels from us, mention this item in the notes and we'll include them for free! ...

New "Mercury" script decal in black for any Mercury, but will be at home on the Cougar. Measures 10 3/4" wide by 1 1/2" tall.This is a die-cut vinyl decal. To install, you'll have to peel off the backing, apply the decal to the intended clean surface, press in place with a plastic squeegee or credit card, then carefully peel away the top contact paper.

Reproduction oil cap decal for the Ford 1965-67 oil caps. 

This decal was used on the Standard model Mercury Cougar for 1968 and both the XR7 and Standard model Mercury Cougar for 1967. Will require slight trimming for perfect fit. If you place a piece of 80 grit sand paper (or file/emery board) on a firm surface you will be able to bring the height of the decal down with just a few strokes of both the upper and lower edge. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive...

Located on the bottom side of trunk lid.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these. Sold as a Pair. Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

Located on either the left or right hand shock tower. On rare occasion we also have seen these above the washer bottle on the 69-70 models. Replaces Ford Part #: C7AE-6C029-A.

Reproduction Sun Visor Decal Starting Instructions for the 1967 - 1968 Mercury Cougar / Ford Mustang 

Reproduction Tire Pressure Decal for the 1968 Mercury cougar

Very correct looking reproduction used only on the 1968 XR7 Mercury Cougar. This decal may need slight trimming to fit perfectly into the recessed portion of your lock cover. Check out this video

Used until early 1970 when vehicle was equipt with AC. Decal Text: Autolite Regulator C8TF-10316-A NEG

This walking cat decal measures 10.5" x 3.65".

This walking cat decal measures 10.5" x 3.65". Check out this video

This walking cat decal measures 10.5" x 3.65".

This walking cat decal measures 10.5" x 3.65". Check out this video

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Pictured below is Robin Miller's "G-Force" Cat! Click on images to enlarge. Check out this video of our 2013 Open House event! ...

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Check out this video

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog.Check out this video of our 2013 Open House event. See you next year! ...

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog. Shown in Black.

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog. Shown in Black.Check out our video f the 2013 Open House event. See you next year! ...

Rare, almost impossible to come by collectors item designed to adhere to the inside of your window. Original water transfer 3" diameter Cougar logo decal. Soak in water for 30 seconds and slide onto glass. I have only seen these dealer "give aways" one other time in all my years of collecting. We want to you to keep in mind that the cloudy areas you see on the decal in the picture are nothing more than paper residue, and will easily wipe off. Check out this video ...

Tips for installation: Decal should be trimmed to resemble the original decal. This one is comes as a full rectangle and the original was trimmed around the edges w/ very little clear border left.This decal is a very "touchy" decal, any air bubbles WILL leave the adhesive white where the bubble was even if you get it smoothed/pushed out so you must put the decal down avoiding ANY air bubbles by laying one edge first and rubbing as you go along. If you just lay the decal down you WILL end up w...

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

Used 6.5 litre Grade A (390) fender emblem for the Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured on our grade B listing with several minor blemishes. No studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the...

Used Grade B 6.5 litre (390) fender emblem for the Mercury Cougar. Most of what we get looks like the one pictured with several blemishes. Often one or more of the four studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. We also have...

Reproduction 6.5 litre (390) fender emblem for the Mercury Cougar. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. Unlike the originals these do not have mounting studs, but are firmly held in place with 3M VHT double sided emblem tape.

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Due to corrosion caused from the exhaust this used emblem will most likely have poor quality chrome. The emblem shown would be the very rare exception.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

Amazing quality that surpasses any NOS or restored emblem you will ever see. This unique emblem was only used on the front fender extension (driver side) of the 1967 and 1968 Cougar. Replaces Ford part number C7WY-16604-A. Here's some info on the measurements for placement: 1. From the bottom of the Y to the right edge of the deck lid - 1.28"2. From the top of the deck lid moulding to the bottom of the Y - 0.18"3. From the top of the deck lid moulding to the bottom of the M - 0.73" Also, note...

Used Driver Side / Right Side Fender Extension Emblem for the 1967 and 1968 Mercury Cougar

New Old Stock "G" and "T" 1967 Mercury Cougar and Ford Mustang individual fender letters. There were two ways that the cars were called out as GT's. Two individual letters and a single box with "GT" inside. These letters were also used on 1970-71 Mercury Cyclone. Both letters sold together. Ford part number C7ZZ-16098-A and C7ZZ-16098-B.

This is a very nice reproduction that we have all needed for many years! You might want to buy a new Cougar walking cat emblem if you replace this background decal as it requires breaking the studs off your old emblem to get it off. Check out this video ...

These Mustang emblems have the incorrect pin placement for the 1968 Cougar so if you have original GT fenders you will have to drill new holes. Once mounted they look correct. Replaces the C7ZB... individual casting numbers. Licensed by FORD

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

This emblem was located on either side of the quarter panel in 1968 and both front fenders in 1971 - 1973. The studs on the 71-73 were a little longer but this 1968 emblem is an excellent substitute. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very consistent. The plating is very inconsistent on the original Ford emblems. We are very excited to...

Two required per car, right is the same as left. Good used Cougar emblem with no pits, deep scratches or broken studs.

These always are peeling. Located on the right side on the dash face...

These were originally painted argent silver with the back ground painted semi-gloss black, they were not chromed. This emblem was used on all 1968 Cougar steering wheels with the exception of the XR7-G.

NOS "C" pillar emblem for your XR7. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford part number C7WY-6528818-B1

Good used "C" pillar emblem for your XR7 with no obvious pitting. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.Ford part number C7WY-6528818-B1 Hi Don: Thank you for fixing me up with the XR-7 pillar emblems. I appreciate doing business with you. It's nice doing business with guys who are not perfect, but try to be and correct anything within reason that is called to their attention. Take care, Greg Worth TN ...

Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no modification. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Note that if you want to replace these emblems...

Poor chrome, for use as a core to be restored.

These are NOS Mercury Cougar XR7-G dash emblems. The version supplied these days from the OEM supplier do not have as definitive of cross hatch pattern and the edges are not as sharp. Another quick way to discern between NOS and new when original packaging is absent is to look at the back side. The backing for the two sided tape on the reproduction uses green vinyl and the originals used a green paper. The most disappointing difference between the new emblems and these NOS Ford supplied...

Assembly required This high quality corral fits perfectly and the chrome plating is well beyond what Ford originally did. The mounting studs are placed in the exact position as original. We have offered the walking cat and black background for sometime now but the challenge has been getting your used corral (or rectangle frame) remounted after you break off the studs to remove the assembly. Replacing this emblem assembly is probably (for the money) the best way to improve the looks of the...

Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only designed to be installed once. Click on images to enlarge. The above is a very sought after collectible that was circulated back in 1967-1968. This picture above (From Jim Pinkerton) is of a pen...