Decals & Emblems

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Check out this video

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog.Check out this video of our 2013 Open House event. See you next year! ...

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog. Shown in Black.

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog. Shown in Black.Check out our video f the 2013 Open House event. See you next year! ...

Rare, almost impossible to come by collectors item designed to adhere to the inside of your window. Original water transfer 3" diameter Cougar logo decal. Soak in water for 30 seconds and slide onto glass. I have only seen these dealer "give aways" one other time in all my years of collecting. We want to you to keep in mind that the cloudy areas you see on the decal in the picture are nothing more than paper residue, and will easily wipe off. Check out this video ...

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

Set of 5 reproduction firewall inspection decals. During final inspection, these decals where placed in different locations on the firewall / cowl area and one P decal between the weatherstrip and dash pad inside the drivers door jam. This decal set has the assembly line inspectors names stamped on them. These decals would have been used on cars equipped with Boss 302 and BOSS 429 engines.

Reproduction Decal Set / Under Hood Paint OK for the 1969 - 1971 Mercury Cougar or 1971 Ford Mustang 

There never was an Eliminator convertible from the factory, but we think there should have been. Since the rear quarter panels are shaped differently, we redesigned the side stripes to fit the contours of the convertible Cougar correctly. Otherwise, these are the same stripes we sell in coupe format, cut from OE-spec 3M Scotchcal vinyl and designed from a NOS stripe kit. The kit includes 17 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, ELIMINATOR rear quarter...

This is our complete black stripe kit for the 1970 Cougar Eliminator. The kit includes 17 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, ELIMINATOR rear quarter panel decals, and the often-overlooked 3-piece rear trim blackout stripes. This is the most correct and complete kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same 3M satin black vinyl that Ford used from the factory. *Convertible owners - If you're planning...

There never was an Eliminator convertible from the factory, but we think there should have been. Since the rear quarter panels are shaped differently, we redesigned the side stripes to fit the contours of the convertible Cougar correctly. Otherwise, these are the same stripes we sell in coupe format, cut from OE-spec 3M Scotchcal vinyl and designed from a NOS stripe kit. Quality and fit are second to none. There was also never a white Eliminator stripe kit in 1970 (unlike 1969) but we figured...

This is our complete white Eliminator stripe kit for 1970 Cougar coupes. There was never a white Eliminator stripe kit from the factory in 1970 (unlike 1969) but we figured we'd make these available for those wanting a custom look. Designed using a NOS stripe kit as a reference, and cut from OE-spec 3M vinyl, fit and quality are second to none. The kit includes 14 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, and ELIMINATOR rear quarter panel decals. Unlike...

Good used pit free emblem that would be good for restoration. Notice the clips are in place and there are no cracks in the plastic backing. The example picture of the installed emblem is what they looked like when restored. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Located on the right hand dash panel of your XR7, requires drilling to remove properly.

Good used plastic emblem with no peeling chrome. This was used on all models except XR7 on the right side. We also have the metal version of this emblem available.

Grade "A" pit free original metal emblem for your Eliminator or Standard model Cougar. If you look closely at our picture you will in fact see tiny imperfections in the chrome. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Grade "B" original metal emblem for your Eliminator or Standard model Cougar. Grade B emblems will have pitting and faded or missing paint. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

Grade A used, trunk emblems for 1969-70 XR7 models. We will very seldom have this in stock, the alternatives are grade B used or reproduction. Please see related items below. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both...

Will show at least a small amount of pitting. Casting number as seen on the back reads D0WB-652803-E.

Left is the same as right, one year only emblem at the center top of the door panel. Usually will show a small amount of pitting. Casting number as seen on the back reads D0WB-6520802.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

Decent reproduction of the 69-70 Cougar fender extension COUGAR script. This emblem was used for 2 years only and was located on the driver side front fender extension (fender cap). The originals came with speed nuts but these have push on clips from the back which means they are easier to install as no tools are needed. If one looks very close you will see minor differences compared to original examples. If you want to trade in your dull, pit free emblem for store credit we will give $20 for...

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside: C9WB-16098-B Ford number C9WB-16098-A. Note that the 1970 version stamped D0WA-16098-A is slightly different, most noticeable on the letter "C".

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside:  Ford number D0WB-16098-A. Note that the 1970 version is stamped D0WA-16098-A.

Reproduction center grille emblem background. This decal is only made with the "7", so you will need to remove the "X" and "R" from your existing decal and adhere them to this new one. You can clean those letters up with some extra fine polishing steel wool. The standard grill emblem with a walking cat uses the same stud configuration as XR7 so you can exchange emblems from one to another. ...

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

Correct anodized aluminum reproduction emblem for 1969-70 quarter panels. These high quality emblems have the black paint applied to the sides just as the originals did. If you want an emblem that better matches your front Cougar script you might want to consider these chrome emblems. You can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines. *NOTE* This item includes the three...

Used COUGAR Script Quarter Panel Emblem for the 1969 and 1970 Mercury Cougar

This "Stick On" Cougar rear deck emblem was only used on models without the XR7 package. They are often missing as once the factory double sided tape dries out they are often lost forever. We also have a few very nice used examples in stock.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Excellent reproduction of the little 1 1/8" wide plastic emblem found on every 1970 - 1974 three spoke steering wheel pad. This emblem can also work on the 1969 - 1973 two spoke steering wheel pad but it is not an exact fit as the two spoke wheel emblem is only 1 1/32" wide. Keep in mind we made these EXACTLY as original so they are very fragile. If you happen to break the emblem anytime within three years of purchasing it we will sell you a replacement for half price when you submit the...

This small sized Cougar emblem (1 3/8" long) was used on 1969 - 1973 Cougars without AC. It was affixed to a block off plate in the very venter of the dash by two peened over die cast studs. It will glue back in place nicely and many Cougar fans have found fun "custom" applications for this attractive piece. This emblem will not be pitted or scratched in any way.

Since our restored emblems look so good we have a hard time selling NOS these days which works out just fine as we only seem to be able to obtain 1 of these every few years. Keep in mind your used cores have trade in value against this NOS part. Casting number seen on back side for the assembly is C9WB-65517A56-A and black plastic is C9WB-65517C00-A, Casting number on chrome is C9WB-65517A20-A

This vinyl piece glues to the center of your block off plated on Cougars not equipped with AC. These often times have shrunk slightly over time. We cannot guarantee to always have all the colors in stock. Call for color availability or put desired color into the comments section of your order.

This grille background piece requires you remove your Cougar emblem before installing. To remove the cat emblem you will need to grind from the backside and epoxy the emblem back in place after-wards. Vast improvement over your current faded, dinged part. Not for use on the xr7. ...

Adhesive backed, located on the right side of your deck lid.  We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often, as you can see one of our example photos above, the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid "somewhat" centered top to...

There are multiple emissions decals available for the 351 Cleveland 2 barrel with an automatic transmission in 1970 for the Mercury Cougar or Ford Mustang. This sticker is printed with part number D0AE-9G485-S.

There are multiple emissions decals available for the 351 Cleveland 2 barrel with an automatic or manual transmission in 1970 for the Mercury Cougar and Ford Mustang.  This sticker is printed with part number D0AE-9C485-A.

Emission Decal for the 351 Cleveland 2 Barrel with an automatic or manual transmission in the 1970 Mercury Cougar or Ford Mustang. Printed with part number D0AE-9C485-AH.

Emission decal for the 351 Cleveland 4 barrel with an automatic transmission in the 1970 Mercury Cougar or 1970 Ford Mustang manufactured before January 1, 1970.  Printed with part number D0AE-9C485-F.

Emissions decal for the 351 Cleveland 4 barrel with automatic or manual transmission on the 1970 Mercury Cougar and Ford Mustang manufactured after January 1, 1970. Printed with part number D0AE-9C485-AG.

Emission Decal for the 428 4 barrel with an automatic or manual transmission in the 1970 Mercury Cougar and Ford Mustang. Printed with part number D0OE-9C485-J.

Exhaust Emission Control decal for the BOSS 302 with a manual transmission in the 1970 Mercury Cougar and Ford Mustang manufactured after January 1, 1970. Printed with part number D0ZE-9C485-F.

Exhaust Emission Control decal for the BOSS 302 with a manual transmission in the 1970 Mercury Cougar and Ford Mustang manufactured before January 1, 1970. Printed with part number D0ZE-9C485-B.

Engine Code Decal for the 302 with automatic transmission and air conditioning on the 1970 Ford Mustang. Printed with L 6° K272AG.

Engine Code Decal for the 302 with a automatic transmission on the 1970 Ford Mustang.  Printed with L 6° K280A.