Decals & Emblems

Fair used fuel door framed insert, without the crest. These most often will not include the thin foil backing plate as shown. "B" grade will have some rust pitting and some dullness on the bright work, overall fair used. Foil inserts available used in limited quantities.

Restored fuel door framed insert without the background decal or crest, for the 1969 - 1970 Mercury Cougar. Foil backing plate available in reproduction. At the moment there are no reproductions on the walking cat, you can however polish up your old cat and re-use it in this frame.

New adhesive backed foil insert that goes behind the walking cat on the passenger side headlight eyelid door on the 1969 Mercury Cougar.  You will likely want to purchase the reproduction walking cat when replacing this foil insert. You will have to break the original studs to remove the cat to replace the foil. The reproduction walking cat comes with two flat attaching clips. We also offer a restored emblem corral (chrome surround) for the walking cat. You...

Replace FORD Part #: C8WB-17093-B

Replaces Ford Part #: C8WB-17093-D.

Correct for the 1969 Eliminator SS wheel. Replaces Ford Part #: C9WB-17093-B

This decal goes on the tire jack itself.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Decal Text: Autolite EV-50 C6AZ-6A666-B Replaces Ford Part #: C6AZ-6A666-B.

Reproduction master cylinder decal for the 1967 - 1969 Mercury Cougar or Ford Mustang. This decal was not used on later year cars. These types of decals are for the person to whom details matter.  Customer feedback found at mercurycougar.net:  Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are...

This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo.   1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...

Automatic chokes had been the norm for many years so a notice to the operator was a must. Decal Text:NOTICEThis vehicle is equipped with a manual choke located immediately below the ignition switch. For proper starting use manual choke. ...

Reproduction Small Block Engine I.D. Bolt for the  1967 - 1973 Mercury Cougar / 1967 - 1973 Ford MustangSold individually 

Replaces Ford Part #: C9WA-19F514-A

Reproduction Space Save Tire Instructions Decal for the 1968 - 1973 Mercury Cougar / Ford MustangThis yellow sticker actually came out in 1971-ish. These were sent to previous owners of cars with space saver tires, with instructions to apply sticker to the space saver rim. We believe that they were factory installed with B.F. Goodrich space saver tires starting in 1971 for safety reasons. 

Reproduction Space Saver Spare Recall Postcard for the 1968 - 1971 Mercury Cougar / Ford Mustang

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. *NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in silver for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 428 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Our reproduction 428 CJ hood stripe kit in sliver with the black Cougar Head is made from quality 3M stock and patterned from an original Ford kit. Check out our video below showing how to install this hood stripe. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can...

Our reproduction 428 CJ hood stripe kit with the black Cougar Head is made from quality 3M stock and patterned from an original Ford kit. Check out our video below showing how to install this hood stripe. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find...

This decal was sometimes placed on the dash face pad near the middle or right side, and sometimes on the sun visor.

This was an instruction tag for the customer on how the Rim-Blow horn functioned. It would have been hanging from the steering wheel when the car was new. See product images for factory placement example.Replaces Ford Part #: C9ZF-13A875-AA

This is an accurate reproduction of the tie down notice decal that was placed on the rear license plate frame. This was to remind dealers to remove the tie down plates that were used to secure the cars to the transport trains / trucks on their way from the factory to the dealers. Ford wanted to recycle these plates to save money, but dealers often didn't feel it was worth their time to remove the plates. Thus, many cars still have them. Check yours out! ...

Used until early 1970 on vehicles not equipt with Air Conditioning. Decal Text: AUTOLITE REGULATOR 15V C8AF-10316-A NEG

This is the correct size walking cat decal for your eyelid door on the 1967 - 1969 Cougar. It has the studs in the exact place as the originals. You will need this emblem when changing out our 1967 - 1969 background decals as you will have to break the original studs to remove the cat. Also great for those custom applications! Emblem is approx 3 3/4" wide by 1 1/4" tall. This cat does come with two flat attaching clips. *Customer Feedback* Hey Don and Lin, Just wanted to send a couple pictures...

New "Cougar" script window decal in black. Measures 6 3/4" wide by 2 1/8" tall.This is a die-cut vinyl decal. To install, you'll have to peel off the backing, apply the decal to the intended clean surface, press in place with a plastic squeegee or credit card, then carefully peel away the top contact paper.

Reproduction emblem for the 390 engine designation. Never used on a Cougar, but an attractive emblem for customizing. Measures 3 1/8" x 3/4" and has two mounting studs.Replaces Ford part # C9ZZ-16637-D.

New in-house cut vinyl applique for replacing the burl wood overlay on your 1969 Cougar console insert.

Here's the original "stereo" decal for the 69 - 70 door speaker grills. If you want to keep your car as original as possible, these are for you. These decals are made from aluminum, and as you know, they can get pretty flimsy after 45 years. We'll do our best to pick out good ones for you. You can get the sticker repro version here. SOLD INDIVIDUALLY. ...

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Check out this video

NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.

NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.

Nice reproduction of the factory installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender.Sold individuallyReplaces Ford Part #: C8OZ-16228-D.

These were obtained from the original manufacturer and have never been mounted. Very rare find!

Rare find in NOS form! 1969 standard model Cougar, passenger side dash plate. Replaces Ford part number C9WB-6504460-A.

Due to the fact these were glued on, they are often missing. Separate "XR" and "7", Grade B used, good for a daily driver. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid...

Original part in Ford box, part number C9WB-16098-A, casting number as seen on back is C9WB-16098-B

NOS front fender extension "Cougar" script. Ford Engineering number as found on the backside:  Ford number C9WB-16098-B. 

NOS front fender extension "Cougar" script. Ford Engineering number as found on the backside: Ford number D0WB-16098-A . 

This version of the emblem was actually used on early 70's full-size Mercurys, and is almost identical to the 1969-70 version used on Cougars. In order to use it on a Cougar fuel door, the studs on the back will need to be trimmed down The only visible difference is the thinner / more numerous ridge lines in the red crest area than on the Cougar version. Casting number on this substitute emblem is D1GB-16607-AA.The original emblems were never sold as a stand alone part from Ford but rather an...

These fuel door Mercury crest emblems are a close to original reproduction. They are an economical alternative to brighten up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. To remove your emblem we suggest grinding down the studs on the backside. To install the reproduction emblem you will need the 26120 trim clip.

These fuel door Mercury crest emblems have been lovingly restored by a long time Cougar enthusiast. They have been carefully repainted the correct colors and will really liven up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. The engineering number on the back is C9WB-65405A92. To remove your emblem we suggest grinding down the studs on the backside. To install the restored emblem you will have to use epoxy glue. Keep in mind you...

Very difficult to find, delicate aluminum quarter panel emblem in the original Ford box. Ford part number is C9WB-6525622-A, casting number on back reads C9WB-65291B62-AYou can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines.

Good used center with no crack, missing paint or broken mounting tabs. This was used on all 1969 Cougars with a three spoke wheel except the XR7.

This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. We rarely have an emblem this nice in stock for more than a few weeks of any one year as the tail was prone to breaking off as well as the "cats" other limbs. We do not list these hard to find parts here to...

This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. The tail will always be broken and probably at least one leg is missing on this grade B part. While not an exact fit our 3 spoke wheel emblem cat will fit on this black background.