Convertible

Used exterior passenger side (right hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the...

Restored driver side (left hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. This unit is basically the same as the coupe version, but this convertible unit has about and inch and a half cut off the end. Because these lower windshield mouldings are lovingly restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. They are an excellent option for you...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part.  Ford...

Used driver side (left hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. These are the same as the coupe, but the convertible piece has about an inch - inch and a half cut off the end. Because these mouldings are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are...

Used passenger side (right hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. These are the same piece as the coupe, however the convertible piece has about an inch - inch and a half cut off the end. Because these are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of...

Restored passenger side (right hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. This unit is basically the same unit as the coupe, but this convertible piece has about an inch and a half cut off the end. Because these side lower windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as...

Used driver side (left hand) exterior windshield pillar post moulding for the Mercury Cougar. Sold on an exchange basis only. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* If you have any questions about your cores,...

Restored passenger side (right hand) exterior windshield pillar post moulding for the Mercury Cougar. Sold on an exchange basis only. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* If you have any questions about your...

Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

Rare to find a diecast ash tray lid with no pitting. This design was used on several convertibles 1964 - 1970 starting the Ford Galaxie. The casting number on the back reads C4AB-7630706.

 Like most examples you will see out there this grade B sliding lid will have minor pitting. This design was used on several convertibles 1964 - 1970 starting the Ford Galaxie.  The casting number on the back reads C4AB-7630706.

Ashtray sliders for the rear interior quarter panels in the 1969 or 1970 Mercury Cougar or Ford Mustang.  Slide handle is ribbed black plastic and has ribbing for strength on the slide cover on this reproduction.Not exactly concours, but a close copy. See the comparison photo. Replaces Ford part # C1AB-7630714-A.

Reproduction C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Slightly deeper than the OEM ash trays, plenty of room for installation. Receptacle only, sliding covered retainer sold separately, find it here. Also fits 1965-68 Ford and Mercury full sized convertibles. 

C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Receptacle only, sliding covered retainer sold separately. Also fits 1965-68 Ford and Mercury full sized convertibles. Decades old gum stuck to the bottom is no extra charge...

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

Keeper or retainer for attaching the convertible top cylinder pins. These are usually broken when replacing convertible top cylinders. One retainer per side.Ford Part # 372552-S These are not a exact replica of the t-bolt retainer, but will work for a replacement for the retainer on the T-bolt on the door windows (T-bolt Ford Part # C8SZ-6523274-A).  Ford part number for the retainer is C7SZ-65234A28-A.

Metal strip that fastens the weatherstrip to the bottom side of the header bow.

This is the stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Stang. This is a very hard part to come by in good shape. Many times body shops will loose this piece while replacing the top. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

No damage original bolt. Sold individually, two required per car.

Slat or pivot bracket for attaching the #4 rear most bow on a 1969-70 convertible top. Sold individually, one for each side needed for installation. Bushing is normally broken or missing, plan on sourcing or making a replacement bushing for the pivot. Ford part number C9ZZ-7650340-A.

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...

Grade B used convertible sun visor bracket assembly for the driver side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results.  These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604123.

Grade B used convertible sun visor bracket assembly for the passenger side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results.  These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604122.

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Very nice reproduction item, comes as shown with the knob marked "TOP". *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash.

PICTURE SHOWS a REPRODUCTION CONVERTIBLE TOP SWITCH - Our USED switch will NOT include a "TOP" knob.USED - Convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Used and tested convertible top switch, it will not come with a knob, or if it does, it will be in poor condition. This switch was also used on Cougars with factory power sunroofs.*Note - The 1970 Mercury Cougar XR7 had the...

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

A quality rust proof stainless steel cable which features all the correct hardware. Sold as a pair. Replaces Ford Part #: C9ZZ-7652806-A.

Reproduction tips and screws for your convertible top welt. It's the strip that goes across the top back side of the convertible top. These are the decorative tips that go on each end of the welt.Each kit includes two tips and two screws.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654607-A and are marked L.H. for the passenger side.

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654606-A and are marked R.H. for the passenger side.

This kit is easier to install than you may think! Five piece kit, comes with installation instructions. Be aware, the seals at the top of the glass do not line up perfectly leaving a gap on the quarter glass top seal. We are working on a solution.  Replaces Ford part # C9ZZ-7653986. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

NEW DESIGN... The consistency of rubber on these strips is soft and supple now.  The doors do not have to be "slammed"  Of the three reproductions versions out, there these are the best.   If you have any NOS to sell we would like to hear about them.Replaces Ford part #: C9ZZ-7602626

NEW DESIGN... The consistency of rubber on these strips is soft and supple now. The doors do not have to be "slammed" Of the three reproductions versions out there, these are the best. If you have any NOS to sell we would like to hear about them. Replaces Ford part #: C9ZZ-7602627

This harness connects the convertible top motor to the under dash convertible top harness under the dash. Fits 1969-70 Mercury Cougar and 1969-70 Ford Mustang. This wire rests in the trough under the passenger side sill plate and goes behind the back seat where the convertible top pump is located.Ford part number C9ZB-15A668-B.

This black wire attaches to the fusible link. The Fusible link connects to the starter solenoid with an eyelet connector, then connects to this wire with a billet connector. This wire then passes through the firewall to mate with the power top switch wiring under the dash. Correct for both XR7, Standard convertibles and power sunroof equipped Cougars in 1969, and Standard Cougar Convertibles in 1970.Casting Number: C9ZB-15A669-BFord Part Number: C9ZZ-15A669-BFits: 1969 Mercury Cougar Standard...

This black wire attaches to the Circuit Breaker coming off the starter solenoid on one end then passes through the firewall to mate with the top switch wiring harness at the other end. We believe that some 1969 harnesses may have used a fusible link wiring harness in place of this one. This harness and the circuit breaker can be used on those applications.Ford part number C9ZB-15A669-B or C9ZZ-15A669-B.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

This pair of reproduction convertible top hooks are beautifully chrome plated and features correct thread size. Looks close to original. These hooks are actually for 71 - 73 Cougars and Mustangs, but will work just fine on the 69 - 70.

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.