Convertible

This black wire attaches to the fusible link. The Fusible link connects to the starter solenoid with an eyelet connector, then connects to this wire with a billet connector. This wire then passes through the firewall to mate with the power top switch wiring under the dash. Correct for both XR7, Standard convertibles and power sunroof equipped Cougars in 1969, and Standard Cougar Convertibles in 1970.Casting Number: C9ZB-15A669-BFord Part Number: C9ZZ-15A669-BFits: 1969 Mercury Cougar Standard...

This black wire attaches to the Circuit Breaker coming off the starter solenoid on one end then passes through the firewall to mate with the top switch wiring harness at the other end. We believe that some 1969 harnesses may have used a fusible link wiring harness in place of this one. This harness and the circuit breaker can be used on those applications.Ford part number C9ZB-15A669-B or C9ZZ-15A669-B.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

This pair of reproduction convertible top hooks are beautifully chrome plated and features correct thread size. Looks close to original. These hooks are actually for 71 - 73 Cougars and Mustangs, but will work just fine on the 69 - 70.

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.

100% complete top frame as removed from a 69 - 70 Cougar. These tops are identical to Mustang with the exception of the rear bow being slightly higher on a Cougar. We carefully break this down by removing the header and crossbows and placing the original bolts back in the holes. Once you get this from UPS it will be very evident how it goes back together.

This used header will be as good as you can get and it can be restored with some TLC. The part you get will be solid with minimal or no corrosion. Ford casting number C9ZB-76514A72-A

AS OF NOW, NONE OF OUR SUPPLIERS ARE MAKING LEATHER UPHOLSTERY. THIS ITEM IS NO LONGER AVAILABLE FROM WCCC. Unfortunately all of the manufacturers of the Leather Upholstery Kits have stopped producing them. Most customers are happy with the Vinyl kits that we offer.

Upholstery components have an ETA of 10 - 12 weeks.Nugget Gold XR7 Convertible Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 -...

Used driver side (left hand) and passenger side (right hand) convertible top boot moulding / trim for the standard Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Ford part # C9ZB-76423A19-A driver side, C9ZB-76423A18-A passenger side. *NOTE* If you have questions about your cores, checkout our video below. Aluminum Trim Restoration & Core Exchange Info ...

Used grade "B" passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years...

This is the trim piece the goes across the top on the inside of the windshield. This piece will need to be sand blasted and repainted. Many people have chromed these, but from the factory they were painted satin silver.Ford Part #: C9ZZ-7603606-B

These convertible black interior "A" pillar mouldings are sold as a pair only. The texture and contour look good when installed but when turned over you will see they are thicker than original and are made from a different material than original. These may require some grinding of high spots on the back side to make them fit flush against the windshield post. Replaces Ford part # C9ZZ-7603598-B and C9ZZ-7603599-B.

Used condition pin and bushings for the 69 - 70 Convertible Cougar or Mustang.

Good used metal strip that fastens the weatherstrip to the bottom side of the header bow. Keep in mind we have (almost) every single used part related to the 69-73 Convertible Cougar and convertible Ford Mustang / Shelby in stock at all times.

This is the stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Stang. This is a very hard part to come by in good shape. Many times body shops will loose this piece while replacing the top. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

This is an example of the best grade A set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

This is an example of the best set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654607-A and are marked L.H. for the passenger side.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels.Basic Ford part number 7631004

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels.Basic Ford part number 7631005

Includes all five pieces. Front bow rubber seal is C9ZZ-7653986-A. Side rubber seals are C9ZZ-7651564-A, C9ZZ-7651565-A. Much better fit than reproduction, perfect for that high end restoration.

Much better fit than the reproductions which make closing your door very difficult for the first year.Ford part # C9ZZ-7602627-A

Much better fit than our reproductions which make closing your door very difficult for the first year. Ford part # C9ZZ-7602626-A

This black wire attaches to the fusible link coming off the starter solenoid on one end then passes through the firewall to mate with the top switch wiring at the other end. Correct for both XR7, Standard convertibles and power sunroof equipped Cougars.

This short section of wiring attaches to the terminal post on the starter solenoid that faces towards the firewall. The other end is a female plug that incorporates a fusible link. If your switch were to get stuck or the frame got in a bind with continued power being applied this is the portion that would blow saving you from a costly wiring "melt-down". This same part was used on both XR7 and standard Cougars with a power sunroof or convertible top.