Overstock

Leaf spring front bolts for any 1969-70 Mercury Cougar or Ford Mustang. AMK F-251, About 4-3/8 inches long. 4 total pieces, 2 bolts, 2 nuts.

Fits all models.

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury...

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

Installation kit for the fastening the new reproduction deck lids to the trunk hinges on the 67 - 70 Mercury Cougar. The reproduction deck lids don't come with the J nuts installed and we've found...

New bolts and nuts for attaching the engine frame stands to the frame. Fits all 1967-70 Mercury Cougar and Ford Mustang with V8 engines. 4 bolts and 4 nuts. 3/8-16 X 3 1/2 Grade 5 phosphate flange...

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1971-73 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-467.

Reproduction Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang. If you're working on both sides of your grille, you will need two kits, one kit will do one half of the grille. ...

Reproduction Headlamp Housing Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang

Fits Standard and XR7

Here are our reproduction hood latch support brace bolts and U nuts for the Mercury Cougar.

Reproduction power steering control valve boot and clamp, for the 1967-70 Mercury Cougar or 1965-70 Ford Mustang. Gold tone clamp, molded rubber boot, and pair of screws. Very accurate...

Reproduction BOSS 302 MT Emission Decal for the 1969 Mercury Cougar / Ford Mustang

Reproduction BOSS 302 Rev Limiter Decal for the 1969 Mercury Cougar or 1969 Ford Mustang 

Reproduction BOSS 302 Rev Limiter Decal for the 1970 Mercury Cougar or 1970 Ford Mustang 

 Reproduction BOSS 302 Valve Cover Decal for the 1969 - 1970 Mercury Cougar or Ford Mustang

This is used on Mercury Cougars and Ford Mustangs equipped with factory A/C. This is the bracket for the valve that stops the flow of warm coolant when A/C is turned on. This is an exact...

Used bracket for mounting the bottom of the quarter window guide to the car body. Fits all 1967-68 Mercury Cougar and 1966-68 Ford Mustang coupe and convertible (non fastback). "L" shaped bracket...

Bare metal power steering hose bracket for any 1967-69 small block Mercury Cougar or Ford Mustang. 289-2V, 289-4V, 302-2V, 302-4V, 351-2V, and 351-4V. No rubber insulator included.

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.

Reproduction concours correct throttle return spring bracket for the Mercury Cougar or Ford Mustang equipped with the 390GT engine. This bracket is shorter in length than the 390-4V piece.Ford part...

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away...

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific.  ...

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford mustangs equipped with disc brakes.

Fuel and brake line fastener kit. Fits all 1967 Mercury Cougar and Ford Mustang with V-8 engines and 2 piece fuel line from tank to pump. Early production 1967 cars used a 1 piece fuel line from the...

Rear Wheel Cylinder (7/8", Left Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. The difference...

Rear Wheel Cylinder (7/8", Left Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. You can find the...

Rear Wheel Cylinder (7/8", Right Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.You can find the...

Rear Wheel Cylinder (7/8", Right Rear). For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. The difference...

Rear Drum Brake Wheel Cylinder for 390, 427, 428 w/ Front Disk Brakes (13/16", Left Hand) The difference in this premium version and the economy version, is that this cylinder will be concours...

Rear Wheel Cylinder (29/32", Left Hand)  Replaces Ford Part #: C3OZ-2262-B and D2ZZ-2262-B.

Rear Wheel Cylinders for 4 Wheel Drum Brakes (15/16", LH). Replaces Ford Part #: C7AZ-2262-C.

Rear Wheel Cylinder for 4 Wheel Drum Brakes (15/16", RH) Replaces Ford Part #: C7AZ-2261-C.

Reproduction Kelsey Hayes driver side (left hand) four piston disc brake caliper as factory installed on 1967 Cougar, Mustang, and Fairlane. 1967 was unique in that it had a 7/16" inlet fitting as...

Reproduction Kelsey Hayes passenger side (right hand) four piston disc brake caliper as factory installed on 1967 Cougar, Mustang, and Fairlane. 1967 was unique in that it had a 7/16" inlet fitting...

Sold individually, 2 required. Ford Part #: C8AZ-2B296-A Check out this video

Replaces Ford Part # 382713-S Sold individually Check out this video

part# 384114-S100 Sold individually Check out this video

Replaces ford Part # 381776-S 3/8-24x2 1/2 9/16 Sold individually, 1 used per side. The other 3 bolts are short, see item 41137.

Replaces Ford Part # 379787-S 3/ 8-24x1 1/2 9/16 Sold individually, 3 used per side. There is one long bolt per side, see item 41138.

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 53.9 mm Center Bore Diameter : 61.8 mm Height : 84.5 mm...

STOPFLEX incorporates a special 4 layer design for superior strength and virtually no volumetric expansion. It starts with a Teflon PTFE core (liner) which is wrapped first in a Kevlar braid,...

Flexible high pressure replacement brake hose for 1967 disc brakes with a 7/16 inch inlet that fits both passenger (right hand) and driver (left hand) sides of the Mercury Cougar or Ford Mustang....

Flexible high pressure replacement brake hose for the passenger (right hand) side of Mercury Cougars and Ford Mustangs equipped with disc brakes.Replaces Ford part # D1ZZ-2078-A.

Please note, this is a Mustang brake hose and the fittings are different for the Cougar. Flexible high pressure replacement brake hose for the rear drum brakes on Ford Mustang and attaches to the...

Offshore Centric brand reproduction flexible high pressure replacement brake hose for the rear drum brakes on Mercury Cougar and Ford Mustang. Attaches to the rear end housing. Replaces...

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with manual brakes. High quality replacement part, but the appearance is not original. Ford originally called this...

This intermediate style Carbon Steel line attaches to the transmission tunnel and connects the brass distribution block in the front to the flexible brake hose at the rear of the car. This version...

For cars with front disc brakes. Late production brake lines were routed under the steering column. This intermediate style Stainless Steel line attaches to the transmission tunnel and connects the...

For cars with front disc brakes. Late production brake lines were routed under the steering column. This intermediate style Stainless Steel line attaches to the transmission tunnel and connects the...

This intermediate style Carbon Steel line attaches to the transmission tunnel and connects the brass distribution block in the front to the flexible brake hose at the rear of the car. This version...

This intermediate style Stainless Steel line attaches to the transmission tunnel and connects the brass distribution block in the front to the flexible brake hose at the rear of the car. This...

This intermediate style Stainless Steel line attaches to the transmission tunnel and connects the brass distribution block in the front to the flexible brake hose at the rear of the car. This...

Early production brake lines were routed 'over' the steering column.

Available in OE Steel or Stainless. This item is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel...

Stainless steel version features extra corrosion protection with correct zinc chromate plated fittings and are exact copies of the originals with color coded fittings.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings like original. This set is correct for both power and manual...

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings.

Reproduction steel lines for the drum brake master cylinder on 1970 Mercury Cougar and Ford Mustang. Connects the master cylinder to the brake distribution block.