Overstock

   Sold individually.

Reproduction rubber body plug for the Mercury Cougar and Ford Mustang. This 11/16" x 15/16" oval unit fits to the top of the cowl underneath the front fenders. These little units are sold...

New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan,...

New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S. ...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right...

Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed...

Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long...

Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake...

Used intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with the 351C engine. This item is sold individually.Ford part # 56145-S.

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete...

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a...

Bolt for attaching the emergency brake Pedal Assembly. This is a 5/16-18 washer head bolt. Sold individually, Three bolts attach the E-brake assembly. Fits all 1969-70 Mercury Cougar and Ford...

Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually

Replaces Ford Part # 43260-S Sold individually

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

3/8-16 X 4.0 GR-8 9/16 AF Zinc Dichromate Replaces Ford Part #: 370584-S

part # 382101-S2 Sold individually

part# 372434-SSold Individually.Head size: 5/8"Thread size: 7/16"

Sold indiviually Phosphate & Oil (gay-black)

Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.

New bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow...

Sold individually # 56354-S

Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351. Sold individually

Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.

Replaces Ford part #375381-S Phosphate & Oil Finish

Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.

Bolt for installing the front bumpers on any 1969-70 Mercury Cougar or Ford Mustang. Threads into the front frame rails. 4 needed per car. Sold individually#56362-S

Front U clamp sway bar bracket bolt, for any 1967-68 Mercury Cougar or Ford Mustang. 3/8-16 x 1.0 Grade 5 bolt. Sold individually, 4 per car. part #20408-S

Reproduction intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with either the 390 or 428 engine. These little units are sold individually. 3/8"-16 X 2 5/8" Grade 8 Phosphorus...

Reproduction intake manifold bolts for the Mercury Cougar Eliminator or the Ford BOSS Mustang equipped with the 302 BOSS engine. These units are sold individually.Replaces Ford part # 56146-S. ...

part # 56131-S

Reproduction 351W Intake Manifold Bolt for the 1969 - 1973 Mercury Cougar - 1969 - 1973 Ford MustangSold individually 

Plain head, fine thread. Not concours, but meets or exceeds original specs. Sold individually. Ford part # 380328-S.

Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block.  Also used on the 1970 Mercury Cougar with 428CJ....

replaces Ford part # B-12764

Rear valance and 1967-70 windshield defroster attaching hardware. Sold individually. Zinc (dark silver)

Replaces Ford Part # 382626-S Sold individually

Reproduction water pump bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These are zinc (dark silver) plated and sold individually. This bolt is approximately 2-5/8"...

Reproduction water pump bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. This bolt has an approximate length of 4" to the shoulder and an overall length of...

Replaces Ford part # 45964-S Sold individually

Reproduction steering gear box bolt. Sold individually

Reproduction water pump / timing chain cover for the Mercury Cougar or Ford mustang equipped with the 289 engine. This bolt has an approximate length of 2" to the shoulder and an approximate overall...

This is the shorter version of the top-loader with no "+" on the head. Sold individually

This is longer of the two with the + on the bolt head.

Reproduction Upper Control Arm To Shock Tower bolt. Sold individually. Replaces Ford part # 38049-S

Sold individually Phosphate & Oil (gray-black)

Ford part #300958-S Sold individually

New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually

Window stop bolt for 69-70 Cougars. Each stop needs 2 bolts. Zinc plated, sold individually. 1/4-20 x 1/2 inch bolt.

Bolts and installation kit for most 1969 Mercury Cougar and Ford anything, including Mustang with 351W engines. Kit includes main pivot bolt and 4 mounting / adjusting bolts as shown. Spacer...

Alternator bolt and installation kit for 1967 Mercury Cougar and Ford Mustang with 390 engines. Includes spacer and pivot bolt and the other three bolts and washers as shown.

Bolt and nut for the clamping the coil into the coil bracket as found in 1967-73 Mercury Cougar and Ford Mustang. Fits all of the various coil brackets used 1967-73 on most all Ford engines. This is...

Bolt and nut for installation of disc brake pedals in any 1967-73 Mercury Cougar or Ford Mustang. See related items for plastic bushings and metal spacer.

Bolt kit for installing front sway bar clamps to the body for any 1967-68 Mercury Cougar or Ford Mustang. 3/8" bolts for 1967-68 cars. Starting in 1969, the bolt size was changed to 5/16". This size...

Bolt kit for installing front sway bar clamps to the body for any 1969-73 Mercury Cougar or Ford Mustang. 5/16" bolts for 1969-73 cars. Starting in 1969, the bolt size was changed from 3/8" to...

Bolt kit for installing the idler and adjusting pulley on any 1968-69 Mercury Cougar / 1968-69 Ford Mustang or 1968-69 Ford / Mercury with small block 289 / 302 / 351W engines. 4 bolts 3/8-16x7/8...

Bolt kit for installing the idler and adjusting pulley on any 1970-73 Mercury Cougar / 1970-73 Ford Mustang or 1970-73 Ford / Mercury with 302, 351W, and 351C engines. 4 bolts 3/8-16x7/8 inch washer...

Bolt kit for installing the idler and adjusting pulley on any 1968-70 Mercury Cougar / 1968-70 Ford Mustang or 1968-70 Ford / Mercury with 390, 428CJ engines. 4 bolts 3/8-16x7/8 inch washer head...

Bolt kit for installing the idler and adjusting pulley on any 1970-71 Ford Torino / Mercury Cyclone, or 1971 Mercury Cougar / Ford Mustang with 429/429CJ engines. 4 bolts 3/8-16x7/8...

AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1969-70 Mercury Cougar and Ford Mustang with 302 or 351 engines. AMK number F-474.