Overstock

These studs attached the taillight housing to the tail panel of a 1969-70 Cougar. 6 used per taillight, 12 required per car. 1/4-20 stud about 1-1/2 inches long. Sold individually. *NOTE* Need help...

Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black) ...

Stud for attaching exhaust manifold heat shield on 1969 Mercury Cougar or Ford Mustang with 351W. Sold individually. Replaces Ford Part # 382592-S

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or...

Stud that screws directly into the 289 exhaust manifold on most 1965-67 Ford 289 engines, including Mercury Cougar and Ford Mustang. Sold individually Zinc (dark silver) 5/16-18 X .62 X .62 ...

Reproduction mounting studs for the side marker light lenses on 1970 Cougars and Mustangs. 2 required per light, 8 per car.Sold as a pair.

Reproduction studs and nuts for the taillight to body on the 1969 - 1970 Mercury Cougar 

Reproduction chrome center cap with red background and chrome Mercury man logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better...

This is the 1968 Cougar visor bracket. Not an exact match for 1971 - 1973, but will work. The hole spacing and distance from the windshield is identical to that on the 71-73, the bracket is just...

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look...

Excellent quality reproduction sun visor assembly for the convertible 1971-73 Mercury Cougar and Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. The original...

Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof). ...

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions...

Reproduction 2 screw rear mount sun visor bracket is only available in black, so plan on painting this unit to match. We have most other unfaded colors in used. Replaces Ford Part #:...

Gray plastic rod with rubber visor tip. Fits most 70's cars built by Ford. Replaces Ford Part #: D3AZ-6504114-B. Customer review: Called WCCC the other day after calling around to a lot of garages...

This decal was sometimes placed on the dash face pad near the middle or right side, and sometimes on the sun visor.

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out this video

Reproduction Backup Light Switch / Manual Transmission / 4 Speed for the 1969 Mercury Cougar / 1969 Ford Mustang 

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with power brakes. High quality replacement brake light switch, but the appearance is not original. Ford originally...

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most...

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury...

Mounts to the rear of the factory installed heater control ventilation control panel on 1967 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C7ZZ-18578-A. ...

Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C8ZZ-18578-B. ...

This exact reproduction mounts to the rear of the factory installed heater control ventilation control panel. Save your knob or consider purchasing the 1969-73 selector button kit, find it here....

This reproduction neutral safety switch is for the early 67 Cougars with a C-4 automatic transmission. It has two small plugs as opposed to one large like the later version we also have listed. Ford...

The correct switch with the correct Connectors and color coded wires. Replaces Ford Part #: D2ZZ-7A247-A, SW-906-A.

Replacement power window switch for the passenger door and rear windows on any 1973 Mercury Cougar or Ford Mustang. Should fit other Ford products. Will not fit the master switch panel. Ford part...

Reproduction one year only switch for the 1968 Mercury Cougar with power sunroof (or 1968 Ford Mustang convertible). The XR7 G used a different switch built into the console but the other Cougars...

This little cover glues onto your spoke at 6 o'clock and serves to cover the gap between where your rubber horn switch starts and then stops. Only Black available in reproduction. We do have a few...

Requires $65 Core Charge.  *NOTE - Keep your red and green lenses because these tachs DO NOT come with them (69 lenses and 70 lenses are different). Three wire tachometer for Cougars. Ford...

Return your core to us for a $65 refund! Three wire tachometer for Cougars. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the...

Return your core to us for a $75 refund! Three wire tachometer for Cougars. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the...

This was an instruction tag for the customer on how the Rim-Blow horn functioned. It would have been hanging from the steering wheel when the car was new. See product images for factory placement...

Reproduction Tail Light / Trunk Light / Courtesy Light Loom Clip for the 1967 - 1968 Mercury Cougar or Ford Mustang 

Sold as a pair. New to the market as of 2009. Take a look at our many pictures below of these bezels installed with original backing plates and lenses. *NOTE* Need help diagnosing a Cougar turn...

Reproduction taillight panel for the 67-68 Cougar. Yet another in a long line of great fitting parts from our friends over at Dynacorn, this replacement taillight panel is perfect for...

Set of 6 reproduction tailllight sockets with wiring pigtails for the 71-73 Mercury Cougar. NOTE: The sockets on the 71-73 Cougar were never meant to be replaced as they are attached to the housing,...

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for...

This specially machined screw tensions the friction clutch assembly in the gearbox.

A quality rust proof stainless steel cable which features all the correct hardware. Sold as a pair. Replaces Ford Part #: C9ZZ-7652806-A.

These tension springs are located on either side of your hidden headlamp eyelids. Our springs are made from the exotic alloy "Inconel". Inconel springs have approximately ten times the memory of the...

The Big Book is here! This cache of cool Mercury Cougar knowledge features 186 entertaining and informative pages that focus on the 1967-73 Cougar. Don Skinner, former editor at the Cascade Cougar...

Here's a new book about the luxury king of classic Cougars, the XR7 G! The book contains many pictures and documents never published before. A great addition to your collection!From the author of...

Here's a new book about the king of classic Cougars, the GT-E! This book starts out with the standard '68 Cougar and XR-7 as both models were available with the GT-E option. The reader is then taken...

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the...

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for...

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the...

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video ...

New water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum without casting marks, sand cast finish. Comes with screw-in cap in...

New thread sealant specially formulated to seal liquid in high temperature applications.

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the...

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long.  *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end. ...

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine. Cable length 24 inches long, check your application. There were size differences between the 2V and the 4V...

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: c5zz-9a702

Reproduction Accelerator Pedal for the 1969 and 1970 Mercury Cougar

Nice new black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Replaces Ford Part #: D1ZZ-9735 and D1ZZ-9735-A

Accelerator pedal assembly that mounts to the engine firewall. For use with any 1969 Cougar or Mustang WITHOUT factory cruise control.

Correct spring, black phosphorus plated. Does not have the same tension as original spring. We also have a Concours spring that has the correct tension. Replaces Ford Part #: C5ZZ-9737-B.*Trivia*...

Good reproduction of the 1967 throttle rod for 289 engines. It will fit on 1968 with any 289 or 302 engine with Ford Autolite carburetors. Will also fit most Holley and Edelbrock carburetors too. We...