Overstock

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear...

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our...

Very good quality replacement speedometer cables. Length: 74 inches Replaces Ford Part # : C9ZZ-17260-B

Formed metal clip that holds the gear end into any transmission. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Spindle nut kit for the 70 - 73 Cougar or Mustang. Thread size is 13/16-20, for spindles starting in 1970 on Mercury Cougar and Ford Mustang V8. Included are nut, cap, washer and cotter pin. ...

Spindle nut kit for the 67 - 69 Cougar or Mustang. This 3/4-16 threaded nut fits most of the 1967-69 brake spindles. The exception would be some of the Boss 302 and some 428CJ equipped cars....

Finally, correct Cougar splash shields! For years, all we had were the Mustang versions that didn't fit right. These are contoured just like the originals to fit your Cougar's fenders. Made from a...

Finally, correct Cougar splash shields! For years, all we had were the Mustang versions that didn't fit right. These are contoured just like the originals to fit your Cougar's fenders. Made from a...

Reproduction spool for the control valve on your 67 - 70 Cougar or Mustang.

This attaches to the bracket mounted on the top side of your pedal hanger over to the clutch pedal itself. Notice that this spring is used with the old-fashioned three-lever spring pressure...

This reproduction emergency / parking brake spring for the V8 Mercury Cougar or Ford Mustang is made from original Ford blue prints. This is the oblong spring that is painted YELLOW like the...

Reproduction hood hinge spring for all 1967-69 Mercury Cougars and 1964-70 Ford Mustangs. Common on many Ford and Mercury cars, this spring has 14 coils like the originals. We've found these springs...

Reproduction plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on...

Replaces Ford Part : C9OZ-9760

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

Exact reproduction of the 1967-68 Mercury Cougar and 1966-68 Ford Mustang clutch release fork to equalizer spring. Upper clutch equalizer to firewall, 289 and 302 engines. This unit will also work...

This spring is commonly missing or broken. Plated to prevent rusting and premature failure. Connects from the top of the equalizer bar to the firewall. Close Reproduction. Slightly longer and softer...

Fits the 1969 and 1970 Mercury Cougar with the 390GT, 428CJ or 428SCJ. Replaces Ford Part #: C9ZZ-7523-B.

This is a non-concours upper clutch equalizer or Z-Bar to firewall spring that fits the 390 and 428 Cobra Jet in the 1969 - 1970 Mercury Cougar or the 1969 - 1970 Ford Mustang.

Z bar return spring for all 1967-68 Mercury Cougar and Ford Mustang. This is the upper spring, proper color and spring tension from original. This is the economy version of the concours spring...

Fits the 1969 and 1970 Mercury Cougar with the 302, Boss 302, 351 Cleveland or the 351 Windsor. Stiffer and 1/8" shorter than our other reproduction. Replaces Ford Part #: C9ZZ-7523-A.

Description: The Ford Master Parts Catalog calls this "Bracket - Clutch Release Lever Retracting Spring". This little "L" shaped bracket is found only on 1967 - 1968 Mercury Cougars and Ford...

This kit contains all the replacement springs and hold downs required to do a professional job on 10" x 1-3/4" drum brakes. Kit includes enough parts for two wheels. *Hint - Use your camera phone to...

Spring nut used to install the fan shroud on a 1967-71 Cougar or Mustang, 4 per car.

Reproduction Stabilizer End Link Bolt for the 1967 Mercury Cougar - 1967 Ford Mustang

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF...

Reproduction transmission cooling lines made of stainless steel for the late production 1970 Mercury Cougar equipped with the C-6 automatic transmission and 428 Cobra Jet engine. These lines are...

Replace those rusty, failing brake lines with these Reproduction Stainless Steel Front Power Brake Drum 5 Line Set for the 1967, 1968 and 1969 Mercury Cougar

Fits 1968 Standard or XR7

Single black Phillips oval headed screw for attaching the face pads onto 1967 Mercury Standard Cougars (non-XR7 models). Sold individually, we also sell these screws under SKU 100022599 in sets of...

As the seasoned Cougar owner will quickly point out, there are several differences between the 1967 and 1968 Standard dash bezels. We have chosen to take the best elements of both years and combine...

As the seasoned Cougar owner will quickly point out, there are several differences between the 1967 and 1968 Standard dash bezels. We have chosen to take the best elements of both years and combine...

Sold individually. Zinc Dichromate (yellow-rainbow)

Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.

replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation...

This is the most complete kit available for the steering box with 1 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your EARLY short shaft 1967 Cougar or Mustang...

This is the most complete kit available for the steering box with 1-1/8 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box...

Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear...

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need...

Reproduction Black Steel / Black Leather steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Black Leather 4 spoke steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Black Leather steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and walking cat center decal. Hardware included.

Reproduction thick grip Mahogany Woodgrain / Chrome steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included. ...

Reproduction Chrome / Woodgrain steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

This deluxe wood-grain two spoke wheel was used on the majority of the Mercury Cougars built for 1968 and many other Ford, Lincoln and Mercury cars through 1969. The 1968 XR7 would always use the...

Reproduction 3 spoke steering wheel pad for the 70 - 74 Cougar or Mustang. Not the best fit, texture is incorrect. No returns on this item please.

We rarely have this panel in stock in grade "A" condition, so we suggest you look close at our grade "B" panels as they need very little attention to become perfect. This unit is also known as a...

Fits Standard and XR7 Sold as a Kit as Pictured.

Reproduction stop bracket for the rear quarter window regulator on any 1967-68 Mercury Cougar and 1965-68 Ford Mustang Coupe and convertible models. Stop bracket for the quarter window regulator...

Replaces stop lamp relay on 1967 Cougars built before 1-3-67. No wiring modifications needed, just plug it in in place of your old mechanical relay in the trunk. *NOTE* Need help diagnosing a Cougar...

Reproduction Universal Strap / Medium Wire Loom for the 1967 - 1970 Mercury Cougar or Ford Mustang 

Reproduction rear deck spoiler stripe in white for the 1970 Mercury Cougar Eliminator. We reproduced these stripes from a NOS kit, and they are the most correct Eliminator stripes on the market...

Reproduction hood stripe kit in White for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head...

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 428 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head...

Reproduction white hood stripe with black Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougars equipped with the...

Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.

Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.

Reproduction 8-32 x 1/2" stud used to attach the convertible boot mouldings on any 69-73 Cougar or 65-73 Mustang. A number of these studs were installed on the mouldings, going through the body...