Bumpers & Trim

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

This is a complete kit for front and rear. If you own a 71 - 73 and then you will need two more bolts. mercurycougar.net: I was in Salem on business Monday when I decided to give West Coast Classic Cougar a call. Don was gone but Lin was there, talk about a nice guy I looked around the shop and Lin got me the parts I needed for my 68 Coupe. I am sure Lin was busy but he took the time to answer any questions I had, swapped a few stories and gave me a real good deal. I recommend anyone needing...

Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Driver side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21547-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

These plates show almost no wear and would look right at home on a show car.NOTE: The plates and plate numbers pictured are exactly what you'll receive.

These plates show average wear and can be used as is, or restored to look new.NOTE: The plates and plate numbers pictured are exactly what you'll receive. 

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair could use a bit of restoring to get back to perfect condition, but they are in good shape and will not have any extra holes like the grade B plates do.   NOTE:  "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair has extra holes drilled, which would need to be repaired (see pictures). They could be restored or used as-is. Because of this, we're selling them at a reduced price. NOTE: "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Driver side upper windshield mouldinig. Suitable for restoration or could fit right in on or your lower quality daily driver. Ford part number C5ZZ-6503145-B.

NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B

Driver side vertical windshield moulding. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part number C5ZZ-6503137-B.

Core lower windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503148-B.

Core passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503144-B.

Core passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503136-B.

NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.

This is a core five piece set of front windshield mouldings for a 1967 - 1968 Mercury Cougar and Mustang (except fastback). These mouldings need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard mouldings of that description. We do not recommend the reproduction, "offshore"...

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually. You can find the reproductions here.Ford Part number C7ZZ-6510182-A

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Restored pair of show-quality passenger and driver side quarter window frames for the 67 - 68 Mustang. Good for both Coupe and Convertible. The only weatherstripping we carry for these frames are the vertical seals, we currently do not carry the Mustang glass to frame seals. These look awesome when restored, better than new. Mirror finish. We take your tired original window frames and have them professionally rechromed. Send your cores in advance to avoid the core charge, or wait...