Bumpers & Trim

Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.

Reproduction foam rubber donuts that help cushion the brace from the tail panel on any 67 - 73 Cougar or Mustang.Replaces Ford part number C5ZZ-6540996Sold as a set of 4.

Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part. Note! Road trash of all sorts, sand, gravel, etc. ends up in the gutter to the right hand side of the road. The front tire tends to form a vacuum and sucks stuff away from the...

1969 and 1970 Mercury Cougar rubber sleeve. Attaches to the front bumper brace tubes. Attaching point is where the side marker wiring harness makes contact with the bumper brace. About 2-3/8 inches long for those wanting to replicate from a piece of thin wall 7/8" ID rubber tubing. Sold individually, two needed per car.

Spot on reproductions of the 1969-70 Quarter Window "Hockey Stick" Moulding priced below what you can have pit free originals re-chromed for. We have found that this 3M product works great for bonding these parts in place permanently. Included with the moulding is super strength 3M double sided, trim tape.Ford part number C9WY-6529035-A.*NOTE* Remember to remove the aluminum bracket from the bottom of your old hockey stick, it is needed to attach to the car and for attaching the outer...

Reproduction driver side (left hand) passenger side (right hand) pair of quarter window mouldings / trim with used mounting brackets attached. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting. We bond these to the mounting brackets in house with a liberal application of 3M Windo-Weld #08609. The factory bonded them together with 3 studs that were heat peened / swedged. Ford part...

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place.We have found that this 3M product works great for bonding these parts in place permanently.Ford part number C9WY-6529034-A.*Note - Remember to remove the aluminum bracket from the bottom of your old hockey...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529035-A

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529034-A

These simple little grille repair clips have been needed since these cars were new! Over the years I have seen many home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will list the all the different FoMoCo applications from the era that these clips apply to. These clips are sold as a set of four. Click on images to enlarge. ...

Used rubber sleeve from the front outer bumper mounting tube bracket. Must be for anti squeak or for protection of the front turn signal wiring harnesses. One per side, sold individually. The Ford part number for this item is D0WB-17B947-A. These were made from rubber tubing with a wall thickness of 1/8 inch. Inside diameter is approximately 3/4 inch, and about 2-1/2 inches long for these 1969-70 bumper sleeves. Limited to available stock. These sleeves were installed on 1969...

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

Shaft assembly for driver side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

C9WY-13B014-A Shaft assembly for passenger side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

Repro bushings (pair) that mount to the grille for the headlamp operating shafts. These hardly ever survive after 40 years. Technically not needed, and most never knew they existed. Sold as a pair, one for each side. When mounted these are tight, it was no wonder they are seldom seen on cars. Even the NOS bushings are tight. We recommend polishing the headlight shaft with emery or sand paper, to make both sides smooth. Definitely add a little bit of lubricant too. Replaces Ford part number...

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 

This nice used original part will have no broken tabs as seen on our grade 'B' version. This grade 'A' part will include two metal clip-on spacers as shown. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior.

This used original part will have a broken tab so you will have to use a over-sized washer or some other clever means of properly attaching it to the underside of your dash. This grade be part will not include the metal spacers seen on our grade 'A' part. Even with a broken tab this is a much better looking and fitting part than our economy reproduction. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. ...

This is a much better quality part then what you see offered elsewhere. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. Clips temporarily not available from supplier. No clips included at this time.

Good used tank as taken from a Western parts car. Differs from other years only in that the vacuum port is located in a different position. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number D0WY-13A185-A.

Good used tank as taken from a Western parts car. Differs from other years only in that the vacuum port is located in a different position. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number D0WY-13A185-A.

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...

Used Driver Side Grade "A" Center Grille Support for the 1970 Mercury Cougar

Used Driver Side Grade "B" Center Grille Support for the 1970 Mercury Cougar

Used Passenger Side Grade "A" Center Grille Support for the 1970 Mercury Cougar

Used Passenger Side Grade "B" Center Grille Support for the 1970 Mercury Cougar

This tubular support gives rigidity to your hood extension which houses your center grille. These are hard to find with no bends or cracks due to the fact that the 1970 hood protrudes in the center.1 required per car.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

This is a tested original FoMoCo headlight switch that will work, there is no warranty. The primary reason we list these old used switches is that some people are missing their switch altogether and need the beveled cup shaped spacer that mates to the dash. As pointed out in our listing for the reproduction headlight switch, the spacer is not included with our new units. Ford part # D0WB-11652.

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

Sold as a pair. New to the market as of 2009. Take a look at our many pictures below of these bezels installed with original backing plates and lenses. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check...

This bracket is used to mount the vacuum storage tank under the driver side fender. Same bracket as was used in 1967 just a slightly different clip. Two required per car, sold individually. Cougar part number D0WY-13B008-A. *Note - The 1967 bracket was used prior to 11/10/1969 built date.

1970 Mercury Cougar hideaway headlight vacuum tank installation brackets (pair) with fasteners. Two different styles of installation brackets for the 1970 vacuum tank found inside the driver side fender. These are tall brackets, the other style utilized 1967 brackets with round spacers.

All parts needed are included to mount your 1970 vacuum storage tank to the core support (backside) under the driver fender. Solid, good original parts found on a Western donor Cougar. Includes short brackets with correct clips, 4 spacers, 4 long bolts with washers, and 4 shorter hex bolts. Typically this kit was used for installing the vacuum tanks until Nov 1969, it is much more convenient to use the more common later kit for the 1970 tank installation.

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact.

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact. NOTE - When sending in your core, light pitting on the upper edge is acceptable. Heavily pitted trim will not be accepted.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will have...