Bumpers & Trim

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16-A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "H", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68 Mercury...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "RL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Requires you to PRE-PAY a core charge of $30. Used grade "B" headlight door actuator for your Mercury Cougar. This grade B actuator has been reconditioned with new seals but will still slowly leak down after time as not all of them will function as new after being reconditioned. These actuators are sold individually on an exchange basis or outright (for an additional core charge). One actuator actuates both headlight doors on the 69-70. This unit also comes with a 30 day warranty. Ford part #...

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental 1969 - 1971 Lincoln...

C9AZ-13A163-C Coil spring for the hidden headlamp hinges on all 1969-70 Mercury Cougars and 1969 full sized Ford cars with hideaway headlights. Sold individually, one per side. 1969 Mercury Cougar including XR7 and Eliminator. 1969 Ford LTD 1969 Galaxie and Galaxie XL 1969 Country Squire Wagons

Used hood latch for a 1969 Mercury Cougar, it will fit the 1970 too. Starting in 1969 until 1970, Mercury had three different hood latches. This late 1969 version has the medium length handle. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number C9WY-16700-B.

Used hood latch for a 1970 Mercury Cougar, it will fit the 1969 too. Starting in 1969 until 1970, Mercury had three different hood latches. This 1970 version has the longest handle, and is the easiest to operate. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number D0WY-16700-B.

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

Attaches behind the drivers side horn on all 1969-70 Mercury Cougar and Ford Mustangs with air conditioning. We believe that this part was installed to maintain clearance with the A/C condenser. Ford part number C9ZF-13925-A as seen in the 1969 Electrical Assembly Manual.

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here! Does...

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out this video ...

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

NOTE: This is a blemished (blurred) license plate. We're selling these at close to nothing for anyone who wants to use the backside for custom painting. The graphics were printed blurry...you can't tell from a distance but up close they're not high quality prints (see photos above).  This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification (in states...

NOTE: This is a misprinted license plate, please see photos above. The holes were accidentally printed over the real holes giving it a double blurred look (the Cougar graphic is fine). We're selling these at close to nothing for anyone who wants to grab a bunch as gifts or collectibles!  This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification...

This part is what holds on 1969 - 1973 Mercury Cougar / Ford Mustang Rear License Lamp Lens.  Replaces Ford part # C5OZ-13566-B or C4AZ-13564-A.

This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification (in states where front plates are optional), for-sale pictures, and even as standalone wall decoration. Plus it makes a great gift for the Cougar lover who has everything else!

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

The four part, die cast vinyl top trim kit requires 15 (right rear under back glass is the odd ball that requires five fasteners) of these speed nut fasteners. These speed nuts also can be used on the 1969-70 Mercury Cougar XR7 dash courtesy light bezels, two for attaching that bezel to the dash pad.*NOTE* These speed nuts only work with factory installed die cast vinyl top mouldings.*NOTE* The factory nuts had a drop of silicone or trim adhesive inside the bowl that acted as a seal. This...

Restored lower left rear window moulding / trim for the Mercury Cougar.

Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, checkout our video below. ...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored passenger side (right hand) vertical windhield moulding / trim for the Mercury Cougar. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part.  Ford part # C9ZZ-7603144-B....

Restored passenger side (right hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. Because this windshield moulding / trim is a restored original piece, it will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. They are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have questions about your cores, check out our video below. ...

Clean cores are required for this service, cores that are turned in for this service that are kinked, heavily pitted or mouldings with several holes drilled into them are not worth restoring. That being said, often all of the gravel pitting usually found at the front cannot completely be removed as it would result in a product that will be too thin.

Restored stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together.  We only sell this item on an exchange basis only, you are required to pre-send your restorable cores to West Coast Classic Cougar. These restored pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7...

This option REQUIRES sending your cores in advance. Used stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together. These pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7 convertible top mouldings. Limited supply of used and restored available.Replaces Ford part...

Used grade "B" driver side (left hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years or...

Restored driver side (left hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We require you send a restorable core in exchange in advance to get this pricing. If your part is missing the aluminum belt-line weatherstrip mount then the part you receive in exchange will also be missing it.Ford part # C9WB-76423A19-A. ...

Restored Passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We require you send a restorable core in exchange in advance to get this pricing. If your part is missing the aluminum belt-line weatherstrip mount then the part you receive in exchange will also be missing it. Casting # C9WB-76423A18-B. ...

This is a freshly rechromed / plated pair of used xr7 convertible boot trim mouldings.  Prior to being restored these parts were good used parts, not heavily pitted parts. Keep in mind the price shown here goes down substantially if you have one or more extra (in addition to the complete set from your car) good quality cores to trade in. If you have xr7 cores to sell lets us know! The casting numbers as seen on the bottom of these boot moulding, hockey stick shaped trim is C9WB-76423A18-B...

Used driver side (right hand) convertible top boot moulding / trim for the Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

Used passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

This good used plastic trim part has been inspected for cracks and scrapes and has been found to be in good used condition. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted. This is the driver side, outer vertical piece for all 1970 Mercury Cougar and Ford Mustangs. 1969 has a different part number, but looks the same. We also sell the 1969 piece with C9Z.. casting number.

This stainless steel driver side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. This is a used part, often times it will have small or very minor dents. These stainless steel pieces shine up nicely with 0000 steel wool. Ford part number C9WY-6520935-A. *NOTE* The use of this XR7 unique trim requires the use of different belt-line weather strips than that of the standard,...

This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. This is a used part, often times it will have small or very minor dents. These stainless steel pieces shine up nicely with 0000 steel wool. Ford part number C9WY-6520934-A. *NOTE* The use of this XR7 unique trim requires the use of different belt-line weather strips than that of the...

These are reproduction driver side (left hand) and passenger side (right hand) drip rail mouldings / trim for the Mercury Cougar equipped with a vinyl top. The vinyl top cars have a wider top edge but a narrow bottom edge. The non vinyl cars have a narrow top edge with a wide bottom edge. We will give credit for your original restorable cores. Replaces Ford part # driver side C9WY-6551726-D, passenger side C9WY-6551727-D.

These restored driver side (left hand) and passenger side (right hand) drip rail mouldings / trim for the Mercury Cougar equipped with a vinyl top have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as a pair, or one side only. This is for the person that is striving for perfection with his show car. Most people are going to be...

Good used driver side (left hand) moulding / trim for the Mercury Cougar equipped with a vinyl top with no dents or deep scrapes ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge. However, both cars can use the same piece.Ford part...

Good used driver side (left hand) moulding / trim with no dents or deep scrapes ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge. However, both cars can use the same piece.Ford part # C9WY-6551726-C.*NOTE* If you have questions...