Brakes

Premium, reproduction, and near concours correct front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. This cable hooks onto your inside foot activated brake assembly inside the car, through the floor board, and hooks to the brake equalizer cable under the car. This unit is very close to an OEM replacement, much better than our economy cable. ...

This used emergency / parking cable anchor bracket is spot welded to your passenger side (right hand) front floor pan and anchors the cable. Comes "as taken from parts car". *Customer Feedback* from mercurycougar.net: "Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting...

Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.

Reproduction emergency / parking brake cable for the Mercury Cougar or Ford Mustang with V-8 engines, that is approximately 133 1/8" long. This unit fits from equalizer to rear brakes and one is required per vehicle.Replaces Ford part # D0ZZ-2A635-A.

Premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one, 31 inches, located on the driver side and is an exact fit for 1970 - 1973 Mercury Cougar and Ford Mustangs. Ford Part # D0ZZ-2A635-B

Front emergency brake cable bracket that welds to the floor under the drivers side floor board.  It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1971-73 Mercury Cougar and Ford Mustang.

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford Part # C7ZZ-2A808-A.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford part # C7ZZ-2A808-A.

Reproduction Bendix single piston major repair kit.Includes all major rebuild parts and new Chromoly piston

Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair.Replaces Ford part # C8AZ-2B299-A.

Each kit contains the seals for one caliper assembly. Replaces Ford Part #: C8ZZ-2B120 and #C8ZZ-2B121

Reproduction chrome master cylinder cap for the Mercury Cougar or Ford Mustang equipped with drum brakes. This quality reproduction has the correct lettering and is correct for 1970-73 Cougars and Mustangs. However, it fits and looks good on all 1967-73 Cougars and Mustangs with other under hood chromed goodies. Will also work fit any other 1967-73 Ford drum brake dual reservoir master cylinders.Replaces Ford part # C7AZ-2162, C9AZ-2162, and D3AZ-2162.*Customer Feedback from Mercurycougar.net*"...

Correct check valve for both power drum and power disc brake cars. Comes with grommet.

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

Exact copy of the hard to find original. This two piece clip is used to mount gas and/or brake line to floor pans.

Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.

Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.

Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet.  Replaces Ford part # C9AZ-2167-B.

This kit is a must when redoing the disc brakes on a 1968-73 Cougar. Includes new brakets (caliper stabilizers), bolts, pins, and clips and rubber dust seals. Kit includes the pair.

This is a much needed part for your disc brake car. It is the correct Proportioning Valve Distribution Block for a 1970-71 Torino, Cyclone, Ranchero, 1970-73 Mustang and Cougar, but can be used on any year with minor brake line changes. Unlike the earlier units the proportioning valve is located internally. Keep in mind we do have a rebuild kit for your original unit so if you have an original FoMoCo block it is a better idea to rebuild it. NOTE! The feedback on this item is that one of the O...

D2ZA-2B328-AA Disc brake distribution block for 1970 through 1973 Cougar and Mustang with factory disc brakes. Mounts to the driver side fender apron with two nuts. Bare block without brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford casting # D0OA-2B328. *NOTE* Starting in 1970 there was a built in proportioning valve. **NOTE** Sometime during the 1972 model year there was a change from the D0OA-2B328-D casting number distribution block.Here’s a...

Kit for rebuilding your drum brake distribution block for Mercury Cougar and Ford Mustangs. Special O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is specifically designed to withstand chemical degradation caused by prolonged exposure to brake fluid.Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

Reproduction driver side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.

Reproduction passenger side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.

Reproduction emergency / parking brake cable return spring for the Mercury Cougar or Ford Mustang. This unit goes underneath the dash of the car and is a part of the emergency / parking brake assembly. Made from the original blue prints to the exact specifications of the originals.Original Ford specs according to the master parts catalog was: 11 1/8" long - 55 CoilsFord Part #: D1ZZ-2A651-A or D1ZZ-2651

NOS emergency / parking brake assembly for the 71 - 73 Cougar or Mustang still in Ford box and never installed.Ford part # D1WY-2780-A.

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang and is as removed from a West Coast Cougar organ donor. All parts are inspected and are good and ready for reuse.Ford part # D1WY-2780-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.

Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.

C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

72 - 73 Mercury Cougar and Ford Mustang Front Drum Intermediate Brake Line made of OE-style steel. Intermediate Brake Lines are the lines running from the front of the car to the back feeding your rear brakes. These lines will run along your chassis all the way back to the rear brake drop hose. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. ...

Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.

Reproduction grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. Replaces Ford part # B5A-1131.

This is a front brake grease dust cap tool. No more dented caps. These are milled from 6061 solid aluminum.

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.

Used grade "B" emergency / parking brake release handle with bezel and cable for the Mercury Cougar. This unit fits both the Standard and XR7. Our grade "B" piece may have a cracked cable sheath and the chrome on the release handle will be flaking or chipping.   Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web...

Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

This used emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.