Brakes

C9ZZ-6501508-B This is the correct hanger for a 1969 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number C9ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and in unused condition. Ford part # C9ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to...

Reproduction brake pedal hanger also known as the brake pedal support for Mercury Cougar and Ford Mustang.

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

This switch mounts on the brake junction block to warn the driver of potential brake failure through a warning light on the dash. Replaces Ford Part #: C8AZ-2B264-A.

Used brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

Reproduction emergency / parking brake pedal pad trim piece for the Mercury Cougar or Ford Mustang. This great little reproduction looks good and is one of the little detail pieces that can separate a nice car from a mint car.Replaces Ford part # C9ZZ-2A487-C.

Used emergency / parking brake pedal pad that features all stainless steel construction. This unit cleans up very well with fine steel wool, has reusable folding tabs, and is easy to install. A great piece to finish off your interior!Replaces Ford part # C9ZZ-2A487-C.

Reproduction vacuum line, mounts into a intake manifold fitting, vacuum hose attaches and runs from the brake booster on 1968-69 Cougar, Mustang, and other Fords equipped with the 289, 302, and 351W engines and disc brakes. Hard line only, vacuum adapter fittings sold separately.

Hard steel, screws into vacuum fitting in intake manifold and receives the vacuum hose that runs from the brake booster on 68 - 69 Cougars and Mustangs equipped with 390 or 428 engines.

Sold individually, phosphate & Oil (gray-black).

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

New front inner wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.25 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

New front outer wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.75 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

Reproduction bracket for mounting the rear axle flexible brake hose. From the factory, these brackets were welded in. Double check your placement for your particular year, when welding the bracket to your car. Has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Replaces Ford part number C7ZZ-2A051-A.

Reproduction passenger side (right hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits in a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2061-B or C9TZ-2061-B.

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

We have discontinued this booster because of changes that made it no longer fit correctly. This reproduction brake booster looks and fits more like the originals than any other on the market. This is an off-shore unit, but of the many out there, it is the only one we feel you can consistently get 10 or more years out of. It comes with a 3 year warranty and no core exchange is required. If you do have a decent original core (any version 1967 - 1970 Midland or Bendix brand), we can credit...

Power disc brake distribution block with proportioning valve. Mounts to the driver side fender apron with two nuts. Plan on testing and or rebuilding before installation. Rebuild kits available here. You'll also need hard lines and the brake warning switch, which is available new or used. Ford part # C8ZZ-2B257. Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

C2OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

Flexible high pressure replacement brake hose for the rear drum brakes on Mercury Cougar and Ford Mustang. The Ford MPC specifies that the 427, 428 and Boss 302 cars used this slightly different hose. The most noticeable difference is the bracket that attaches to the differential and the larger size fittings. Attaches to the rear end housing. Replaces Ford part number C9ZZ-2282-A.

Stainless steel version features extra corrosion protection with correct zinc chromate plated fittings and are exact copies of the originals with color coded fittings.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings. New copy of the 1968-69 Mercury Cougar and Ford Mustang manual drum brake master cylinder lines. 

Two-piece Stainless Rear Axle Brake Line Set 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any possible...

Two-piece Stainless Rear Axle Brake Line Set 67, 68 & 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any...

Also correct for some 1967 models with proportioning valve at front

Replacement brake pedal pad trim for the Mercury Cougar or Ford Mustang equipped with a manual transmission. Replaces Ford part # D1ZZ-2A487-B.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unit is for use with a clutch pedal and has a shorter arm than power brake pedals. The brake pedal is shipped bare. Fits any 1969-70 Mercury Cougar or Ford Mustang.Ford part # C9ZZ-2455-B.

Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...

Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...

Reproduction pair of drum spindles for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and...

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

New old stock check valve for Bendix brake boosters. This is a white plastic check valve. Ford part number D0AZ-2365-A.Check the related items, for a reproduction rubber grommet.

As seen in our YouTube video, this is a representation of the used, rebuilt and reproduction parts that we recommend you purchase to convert to disc brakes. If you do purchase this package we will insist on speaking with you prior to shipping as you may want to substitute parts based on what year your car is, manual or automatic and what style booster you prefer. Also know that if your car already has power drum brakes we will be able to reduce the price substantially as no booster or pedal...

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

These is the correct driver side backing plate (sometimes called a splash shield) for 1968 - 1973 Cougars and Mustangs. Sold individually by side, each plate comes with the backing plate retainer. No other hardware is included. Although these plates fit the 68, they're cosmetically different in that 68 did not have cooling scoops.

These is the correct passenger side backing plate (sometimes called a splash shield) for 1968 - 1973 Cougars and Mustangs. Sold individually by side, each plate comes with the backing plate retainer. No other hardware is included.Although these plates fit the 68, they're cosmetically different in that 68 did not have cooling scoops.

Complete reproduction emergency / parking brake assembly for the 1969 Mercury Cougar or Ford Mustang. The 1969 model used a T shaped chrome release handle and 1970 used a black plastic T shaped release knob. This version has the chrome handle. There is not a plastic T handle reproduction available. Replaces Ford part # C9ZZ-2780-A.

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang and is as removed from a West Coast Cougar organ donor. 1969 had a weak design and the release levers were prone to bend and break off. 1969 used a T shaped chrome release handle and 1970 used a black plastic T shaped release knob, which generally aren't interchangeble. Seldom in stock, please check out the reproduction version.

Reproduction front seal for the Bendix brake booster used on all 69 - 70 Cougars and Mustangs as well as many other FoMoCo products that use this size of Bendix booster. This seal prevents brake fluid from entering the booster cavity once the master cylinder fails.