Brakes

Unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Longer arm than drum brake pedals. Keep in mind automatic transmission brake pedals can be trimmed down to work as manual transmission pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* On some 1968 Cougars you will have to drill holes in your existing pedal hanger (many are pre-drilled) to accomomdate the power brake pedal. Since systems with a vacuum booster...

Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...

Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...

Reproduction pair of drum spindles for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and...

Reproduction front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. These are made just like the originals, are concours correct and includes the firewall seal and firewall bracket. Replaces Ford part # C7ZZ-2853-A.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

As seen in our YouTube video, this is a representation of the used, rebuilt and reproduction parts that we recommend you purchase to convert to disc brakes. If you do purchase this package we will insist on speaking with you prior to shipping as you may want to substitute parts based on what year your car is, manual or automatic and what style booster you prefer. Also know that if your car already has power drum brakes we will be able to reduce the price substantially as no booster or pedal...

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

Used emergency / parking brake assembly for a Mercury Cougar or Ford Mustang as removed from a West Coast Cougar organ donor. This unit may have some minor rust. Normally we assemble with reproduction cable.Ford part # C7ZZ-2780-B.

Used service replacement, black plastic filter retainer for the Mercury Cougar, Ford Mustang and other Fords equipped with Midland Booster. It fits between the master cylinder and brake booster on the aluminum master cylinder spacer. The repro and service replacement filter covers are usually black not white.You can find the filter here. ...

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya! Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

New old stock Bendix master cylinder for 1968-69 Mercury Cougar and Ford Mustang with factory power disc brakes. This is a Bendix manufactured MC with proper 2227161 number and stop bolt on the bottom. Also has the dimple forward of the front brake line.  Includes a new cap with diaphragm as shown. The cap is not assembly line correct as this is a service replacement part.*Note even though this is a brand new unit, it should be tested for leaks prior to installation. Things happen when...

Reproduction master cylinder for the Mercury Cougar or Ford Mustang equipped with drum brakes. These are brand new Cylinders, not rebuilt.

This is identical to the 67 pad just slightly wider. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part number D3ZZ-2454-A

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Cylindrical shaped brass valve, some times called the pressure control valve or 'cigar' valve. Starting in 1968, disc brake cars have it mounted almost directly on the Pressure Differential Valve on the driver side fender apron. The pressure differential valve is also commonly called the 'brake distribution block'. We also sell our brake distribution blocks complete with the proportioning valves. The C8OA numbered proportioning valve started way late for the 1968 model year. We almost...

Reproduction rebuild kit for the disc brake master cylinder on any 1967 - 1972 Cougar or Mustang with disc brakes.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Motorcraft new old stock brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a service replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. C7ZB-13480-B Replaces Ford Part #: C9VY-13480-A.

NOS brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated stud with correct 1/2 x 20 threads. 1-11/16 over all length, fits 0.61" hole. Replaces Ford part # C3AZ-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Specific to 68 - early 70 Cougars and Mustangs.The only difference between the late and early pigtail is that the early plug is black and the late plug is white. No difference in wiring.