Body

3 1/8" Style Steel Wheel Spare Tire Hold Down. Available in Black or Chrome. Ford Master Parts Catalog indicates that this hold down was found on some 68 and 69 Cougars with SS Wheels. You may need to bend the ears in slightly to get them to fit properly inside the hole in the center of the wheel. Replaces Ford Part #: C8MY-1424-A.

Reproduction spare tire hold down kit for the 1967 Mercury Cougar or 1965 - 1967 Ford Mustang. Included in the kit are the wing nut, hold down disc and the J bolt. Exact reproductions of the originals. Check out this video

The four part, die cast vinyl top trim kit requires 17 (right rear under back glass is the odd ball that requires five fasteners) of these speed nut fasteners. These do not work in conjunction with the various dealer installed aluminum vinyl top mouldings. *NOTE* The factory nuts had a drop of silicone or trim adhesive inside the bowl that acted as a seal. This procedure is advised for reinstallation.

Finally, correct Cougar splash shields! For years, all we had were the Mustang versions that didn't fit right. These are contoured just like the originals to fit your Cougar's fenders. Made from a nice reinforced rubber compound, these are great replacements for your cracked, broken originals. Salvage your original metal brackets and attach these new seals. 1967 and 1968 are different. NOTE! In 1967 about half or more of Cougars made came with the Mustang fender contour on the larger rear...

Finally, correct Cougar splash shields! For years, all we had were the Mustang versions that didn't fit right. These are contoured just like the originals to fit your Cougar's fenders. Made from a nice reinforced rubber compound, these are great replacements for your cracked, broken originals. Salvage your original metal brackets and attach these new seals. 1967 and 1968 are different. Staples included.

Reproduction original style chin spoiler. Nice quality, fit and finish. Made from thin plastic just like the originals. Comes as bare black plastic, so we suggest coating with your favorite semi-gloss black paint for a more finished look. Take a look at the 1:33:00 mark in the video below to see how we compare the reproduction to the original

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. A lower front chin spoiler / air dam was never an option for the 1967-68...

DROP SHIP ETA - 4 WEEKSUnbelievable, truly authentic concours restoration quality reproduction spoiler kit includes the wing blade constructed of an ABS based thermoplastic and is molded in gray (as original). It's not fiberglass. This two-piece wing (as original) derives its rigid stability from the material itself (as original) instead of some secondary internal support such as a metal rod or foam. And it's not light weight, it's the right weight... at over 8 lbs.! All dimensions are...

Show quality, correct weight and markings. Sold individually.

Very close to correct spring finish (dark color) and tension. Above is a comparison to the other reproduction, which does not have the correct finish, is not the correct length, and does not have the correct tension. Replaces Ford Part # : C8ZZ-17119-A *Note* Must be used with the correct mounting bracket. See below. ...

Reproduction hood hinge spring for all 1967-69 Mercury Cougars and 1964-70 Ford Mustangs. Common on many Ford and Mercury cars, this spring has 14 coils like the originals. We've found these springs to be of lesser quality than the originals, and they will stretch over time and not hold the hood up very well. We highly recommend you stick with original OEM springs. No returns on these springs. Click here to see our listing for good used originals. Replaces Ford part # C3OZ-16789-A. You can...

Coil hood hinge spring, 5-13/32" in overall length, 14 coils, coil diameter 1.899 inches. Sold individually, one per side. Other applications include:  1967-69 Mercury Cougar1967-70 Ford Mustang1965-69 Torino, Fairlane, Ranchero1965-70 Falcon 1965-66 Falcon Ranchero Ford part # C3OZ-16789-A. You can find the hood hinge apron nuts here.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Hood hinge spring specific to the 1970 Mercury Cougar. Total spring length 4-55/64" long, coil spring thickness is 0.222", and the coil diameter is 2.181 inches. 1970 spring is shown on the right side in the inset picture comparison. Stronger hood spring to compensate for the extra weight of the 1970 hood extension. One year spring. Springs sold individually, one per side.Ford par # D0WY-16789-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang...

Hood hinge spring for Mercury Cougar and Ford Mustang. Coil spring type with 6-1/4 inches of overall length. Sold individually, one per side. Ford part # D1ZZ-16789-A. *NOTE* Excludes 1971-73 Mustangs with ram air hood option.  

This spring has two functions. The first is to connect the rod that opens the latch to the deck lock cylinder. The second is to put tension on the cylinder so as to return the key to its perpendicular resting place after unlocking the deck lid. Check out this video

Used pair of diagonal support / stabilizing brackets for the 67 - 68 Cougar. The bars are located behind your back seat and help with stabilizing the car and to prevent the body from torquing or twisting. For added support we recommend installing our seat divider panel. These brackets will be cut out of a scrap car and sent to you as is and will need to be trimmed and cleaned up for paint. Check out our video on front suspension and chassis upgrades below: ...

Used upper shock mount for Q code 351CJ and 351C-4V Cougars from 1972-73. We think. Probably includes 4 speed cars too from 1971. Bracket appears to be slightly different than the Mustang version of the same generation. Pretty rare bracket, likely needed the competition handling package option, with the 351C-4V engines. Basic Ford part number is 18A000. This is the staggered upper shock, mount that goes behind the rear axle on the passenger side. When purchasing, do know that there will be...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

Best of the best in Western sheet metal! Just sand, paint, and install. This unit is also known as a bumper filler, rock guard, or filler panelFord part # C7WY-17779-A.

Quality reproduction stone guard for the 1969 Cougar. This unit is also known as a bumper filler, rock guard, or filler panelReplaces Ford part # C9WY-17779-A.

Price does not always dictate value... Our grade "B" stone deflectors have very minimal, easy to fix damage. The damage is most often found on the corners and would be hard to detect often times even if you chose not to fix them at all. Due to the flat, simple design of these stone deflectors most people with little or no experience in body work would be capable of making them look new again. We guarantee you will not find and rust (other than surface) and no signs of excessive filler. We have...

Price does not always dictate value... Our grade "B" stone deflectors have very minimal, easy to fix damage. The damage is most often found on the corners and would be hard to detect often times even if you chose not to fix them at all. Due to the flat, simple design of these stone deflectors most people with little or no experience in body work would be capable of making them look new again. We guarantee you will not find and rust (other than surface) and no signs of excessive filler. We have...

Price does not always dictate value... Our grade "B" stone deflectors have very minimal, easy to fix damage. The damage is most often found on the corners and would be hard to detect often times even if you chose not to fix them at all. Due to the flat, simple design of these stone deflectors most people with little or no experience in body work would be capable of making them look new again. We guarantee you will not find any rust (other than surface) and no signs of excessive filler. We have...

Reproduction stone guard for the 67 - 68 Cougar. Also known as a bumper filler, rock guard, or filler panel.Replaces Ford part # C7WY-17779-A.

We rarely have this panel in stock in grade "A" condition, so we suggest you look close at our grade "B" panels as they need very little attention to become perfect. This unit is also known as a bumper filler, rock guard, or filler panelFord part # C9WY-17779-A.

Very hard to find with no damage but we have a few! No rust other than surface, no obvious filler and no dents. Grade "A" Western sheet metal is always going to be your best bet when you can find it. This unit is also known as a bumper filler, rock guard, or filler panel.Ford part # D1WY-17779-A.

This is the steel center section only. Very hard to find with no damage but we have a few! No rust other than surface, no obvious filler and no dents. Grade "A" Western sheet metal is always going to be your best bet when you can find it.This unit is also known as a bumper filler, rock guard, or filler panel.Ford part # D3WY-17779-D.

This solid, grade "B" part will not have damage in the hard to fix contoured areas. This is a good value for the money, we will not send you junk. This unit is also known as a bumper filler, rock guard, or filler panel.Ford part # D1WY-17779-A.

Reproduction rear deck spoiler stripe in black for the 1970 Mercury Cougar Eliminator. We reproduced these stripes from a NOS kit, and they are the most correct Eliminator stripes on the market today. Cut from the same 3M vinyl as original.Also sold in a complete kit.

Reproduction rear deck spoiler stripe in white for the 1970 Mercury Cougar Eliminator. We reproduced these stripes from a NOS kit, and they are the most correct Eliminator stripes on the market today. Cut from the same 3M vinyl as original.

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. *NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in silver for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in White for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 428 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Our reproduction 428 CJ hood stripe kit in sliver with the black Cougar Head is made from quality 3M stock and patterned from an original Ford kit. Check out our video below showing how to install this hood stripe. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can...

Our reproduction 428 CJ hood stripe kit with the black Cougar Head is made from quality 3M stock and patterned from an original Ford kit. Check out our video below showing how to install this hood stripe. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find...

Reproduction black hood stripe with silver Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction silver hood stripe with black Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction white hood stripe with black Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction black hood stripe with NO COUGAR HEAD for the 1969 Cougar with the 351W engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction black hood stripe with silver Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction silver hood stripe with black Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction white hood stripe with black Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.

Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.

This kit mounts the spoiler pedestals to the trunk lid. Studs measure 2-3/4" long, correct for the Concours correct stands.Some economy or generic kits come with 1-1/2" studs

Pair of reproduction sub frame connectors, designed to tuck up against the floor pan as tightly as possible to maximize ground clearance. The more performance improvements you do to the vehicle, the more demands are put on the uni-body. Sub frame connectors provide resistance to chassis flex, therefore increasing the integrity and rigidity of the chassis. Installing them will also help reduce rattles and squeaks from the car flexing over rough roads.They are a must for any performance...

This is the 1968 Cougar visor bracket. Not an exact match for 1971 - 1973, but will work. The hole spacing and distance from the windshield is identical to that on the 71-73, the bracket is just 1/8" longer on the side that actually holds the visor tip. This unit is only available in black or neutral. We have most other unfaded colors in used. This item works for 68 Cougar Coupe, 68 Mustang Coupe / Convertible and 71-73 Cougar Convertibles. Replaces Ford Part # C8ZZ-6204132, C8ZZ-17690 OR...