Body

C9AZ-6521760-A Front door window stop bracket. Stops the window in the up position. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door.Same bracket is used on both driver and passenger sides.

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

Only fits Ford Mustang 1969-70.

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install.  These are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Sold as a Kit as Pictured.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

This reproduction hood latch and catch screw and U nut kit fits both the Standard and XR7 and is sold as a kit as pictured.

This reproduction hood latch vertical support screw and U nut kit fits both the Standard and XR7 and is s sold as a kit as pictured.

This is our used driver side (left hand) upper rear fender brace. Welds to the upper cowl on any 1969-70 Mercury Cougar and Ford Mustang Ford part number C9ZZ-16A005-A driver side, C9ZZ-16A006-A passenger side.

Used passenger side (right hand) upper rear fender brace that brace visible when you open the door and look in the upper part of the fender void. Welds to the cowl on 1969-70 Mercury Cougar and Ford Mustang. Ford part number C9ZZ-16A006-A passenger side, C9ZZ-16A005-A driver side.

Reproduction stamped steel firewall for Mercury Cougar and Ford Mustang.Here's our video on front suspension and chassis upgrades.

Pair of reproduction firewall to shock tower braces for the Mercury Cougar or Ford Mustang. These Chinese made units are already painted black, so the only thing you need to do is bolt them on. However, we highly recommend that you get our superior quality used FoMoCo units right here!Replaces Ford part #'s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand). ...

These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan.Includes driver and passenger sides.

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Reproduction passenger side (right hand) inner front frame patch for the Mercury Cougar or Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Reproduction full one piece front frame rail for the driver side (left hand) of the Mercury Cougar or Ford Mustang. Replaces Ford Part #: C7ZZ-6510219-B.Here's our little film to help you fortify your flexxy feline!

FULL inner and outer passenger side (right hand) reproduction one piece frame rail for the Mercury Cougar or Ford Mustang. Replaces Ford Part #: C7ZZ-6510218-B.Here's our little film to help you fortify your flexxy feline!

Reproduction driver side (left hand) front inner apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

This fusible link is a section of wire connecting the starter solenoid on one end and wiring harness that passes through the firewall to mate with the top switch wiring. Correct for power sunroof equipped Cougars. May also work for XR7 and Standard convertibles.

NOS C7ZB-6522449-A Driver side small size pad or gasket for the exterior door handle. Driver side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

NOS C7ZZ-6522428-A Passenger side large size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

NOS C7ZB-6522448-A Passenger side small size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

Premium quality, exact fit plastic gasket set for both the driver and passenger side door handles. Also fits 66-71 Ford Fairlane and 70-71 Cyclone / Torino as well as several other Mercury, Ford Lincoln models. We are the exclusive retailers in the U.S. for this quality kit.

Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.

These are Concours quality with correct bevel and markings.. Sold as a pair.

This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.

Used grommet for protecting the trunk light wiring as found on 1967-70 Mercury Cougar and Ford Mustangs. Ford part number C4AB-14603-A.

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Fits Standard and XR7 Sold as a Set as Pictured.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Improved reproduction left hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit and adjust these hinges without the spring installed on them. We use an old section of seat belt for removing...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the spring. These will work on all 1967-70 as well. But...

Improved reproduction right hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit an adjust these hinges without the springs installed on them. We use an old section of seat belt for removing...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. You can find the hood hinge apron nuts here. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with...

This reproduction hood hinge nut and bolt kit fits both the Standard and XR7 and is sold as a kit as pictured. These connect the hinge to the hood itself, and connect the hinge to the fender apron.

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...