Body

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522811-A

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror on the passenger side. This fits any FoMoCo Sport mirror 69 and up, left hand only. Comes with two round pieces of double sided tape. Keep in mind if your lens is bad and it...

Reproduction passenger side (right hand) sport mirror lens for the Mercury Cougar or Ford Mustang and Torino. Replaces Ford part # C9AZ-17698-B. Dimensions: 4 7/16" x 2 15/16" This version does NOT include the wording "objects in mirror are closer than they appear". We also sell the version with the wording. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Installing a passenger side mirror and Riv-Nuts video: Installing replacement glass in Sports side mirror: ...

Reproduction convex lens for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Replaces Ford part # C9AZ-17698-BThis version included the words "objects in mirror are closer than they appear".We also sell the version without the wording. Do you have questions about installing a passenger side mirror or using...

Lens with mounting hardware only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Count on the glass being scratched. The value here is in adjustment / mounting hardware. This unit will be guaranteed to keep its adjustment and not be loose like many have become over the years. Keep in mind this item is...

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

Reproduction Replacement for the Rear License Plate Lens for the 1969 - 1973 Mercury Cougar or Ford Mustang.  We also have good used original OEM lens that can easily be cleaned to look as good as these Chinese reproductions. Replaces Ford part #: C4AZ-13564.

Latch rod that links the door latch and the inside door handle, driver side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521941-A.

Latch rod that links the door latch and the inside door handle, passenger side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521940-A.

Replaces Ford Part # C7AZ-6243505-B Click on images to enlarge.

Originals keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar. will fit 1971-73 Cougars, but trunk clip may be different. These used originals are much better than the reproduction lock sets.OEM FoMoCo parts.

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. 1971 - 1973 Cougar only.

New Old Stock, NOS, original keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket, glove box stainless bezel, and screws. Fits all 1971-73 Mercury Cougar.  OEM Ford part number D1AZ-6543507-A.

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1970-73. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Sometime after 1973, Ford changed the ignition lock cylinder end. We know it works through 1973, not sure of the change. It must fit the brass lock gear at the bottom of the cylinder hole in the side of the steering column. Refer to your shop manual for removal and installation. Includes two...

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

Used original driver side (left hand) key lock to latch door lock rod for anu 1971-73 Mercury Cougar or Ford Mustang.Ford part # D1ZZ-6522135-A.

Used original passenger side, (right hand) key lock to latch, door lock rod for any 1971-73 Mercury Cougar.Ford part # D1WY-6522135-B.

Reproduction lock cylinder set for the ignition and doors on the Mercury Cougar or Ford Mustang. Replaces Ford part # D2AZ-6222050-A.

This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664

This part mates to and is held down by Golde #100 413 682. The Golde part number for the smaller, lower elbow guide is 100 413 663

Used bracket for installing the vertical seat cushion on a 1971-73 convertible Mercury Cougar or Ford Mustang. Two required per car, sold individually. Not sure of the Ford number, this part went obsolete many years ago. Please take multiple measurements of the location of your old brackets prior to removal. 

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has the elongated hex socket portion. There is also a version that has a rounded upper section formed on the socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A...

Not 100% concours correct but close close in design to the 1968 - 1973 handle. Works well for 1967 as well. Replaces Ford Part Numbers: C5ZZ-17032-A, C5ZZ-17032-B ,C8ZZ-17032-A, D0ZZ-17032-A, D4ZZ-17032-A.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts...

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has a rounded upper section of the hex lug socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A (Factory Service Replacement since 1974) If you'd like a particular...

Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...

Authentic looking hard reproduction plastic Sport Mirror pad gasket. Correct for driver side Cougar Sport Mirrors 1971-73 and passenger side Torino / Cougar Sport Mirrors 1970-73. This is the best fitting gasket we've found so far. You may have to punch out the hole for the remote mirror cable. Replaces Ford #: C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using...

Straight Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering.  It will also help reduce the chances that your shock towers will develop stress cracks over time. Note: Not for A/C or Convertible applications. This product will not clear the distributor or A/C Compressor.  Replaces Ford part # D1ZZ-16A052-A. "Times New Roman"">...

Good used motor taken from a 71-73 Cougar. Motor has been taken apart, serviced and tested. We only sell these on an exchange basis and you must send your core in advance.

Use interior quarter window moulding for the passenger side (right hand) of the Mercury Cougar coupes. This trim installs vertically behind the quarter window. Unfortunately we cannot guarantee that we will be able to supply the color of your choice, but we will try to accommodate. Ford engineering #1971-1972 D1WB-65517A86-AWA,1973 D3WB-65517A86-AWA

This trim part fits on the driver side (left hand) of the package tray between the backseat and the rear window. These are often sun baked, but we will try and pick out a nice clean one for you. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate. Ford Engineering # D1WB-65310A33-AWA (on the backside).

This trim part fits at the passenger side (right hand) of the rear window package tray. These are often sun baked, but will will be sure to try and pick out a nice clean one you. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate. Ford Engineering # D1WB-65310A32-AWA (on the backside).

Driver side metal trim part that that runs along the interior roof edge and connects the "A" pillar plastic moulding to the rear window (quarter window) moulding on the inside. These came color keyed to the trim, most will need a fresh respray on interior paint. Please include desired color in the comments section and we will try to accommodate you if at all possible.

Metal trim part that connects the "A" pillar plastic moulding to the rear window (quarter window) moulding on the inside. These came color keyed to the trim, most will need a fresh respray on interior paint. Please include desired color in the comments section and we try to accommodate you if at all possible.

According to the MPC 1970 primarily, a few 1971-1973's. If you have a hardtop or coupe, (VIN numbers starting with either 0F91 or 0F93) and standard wheels with hub caps. Or, any 1971 - 1973 with style steel wheels. Total length is 6-1/4 inches, with 4 inches being threaded. Threads 1/2-13. We find this bolt to only have 2 1/2" of threads. More data is needed as the MPC is not reliable on these items. What do you have in your trunk? We want to know! Search words 70 71 72 73 1972

1971 - 1973 Mercury Cougar hard tops and coupes with regular steel wheels and hub caps. J bolt total length listed in MPC is 8-3/4 inches, with 6-1/2 inches threaded on the straight end but we find the actual length to be 10" long with about 4" of threads. We also see this used with the 1971 - 1973 Kelsey Hayes Styled Steel wheel even though the MPC lists another size. There are absolutley to absolutes when it comes to items like these and what Ford "may" have called for. Would love to hear...

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

These fasteners were used to keep your package tray in place. In 1971 - 1973 three clips were used, held in place with screws. Sold individually.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.This VHT roll bar and chassis paint will give the appearance of an expensive, baked on finish. Heat resistant to 250 degrees, this epoxy coating also resists chemicals, rust, corrosion and salt. No primer is needed. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...