Automatic & Manual Transmission Shifter Parts

Swivel that mounts to the lower clutch rod or clutch adjusting rod. Original Ford part number D0ZZ-7A528-A.

Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

High quality rubber molded around a flexible steel insert. Insert is cadmium plated to prevent rust. A popular replacement item, as they always wear. While this unit also fits the 1965-68 Mustang, it is only correct for the 1968 Cougar XR7-G. Replaces Ford Part #: C5ZZ-7D351 Check out our video on rebuilding your shifter below: ...

Both our A and B quality bezels will need a replacement brushed aluminum overlay. This used bezel will have no broken or missing parts. Most likely the white will be missing from the P R N D 2 1. We also have grade "B" used units with minor flaws for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand...

Both our A and B quality bezels will need the overlay replaced. Cosmetically this bezel will be as good as our grade "A" units, but when you turn them over you will notice one or two of the feet will be broken off. These missing feet may make it a little more cumbersome to install and if someone walks on your installed console these feet do provide support. Obviously it would be easy to glue on some feet (or spacers) but this item will install just fine without them. Most likely the white will...

This shift indicator will work on a 1967 or 1968 Cougar or Mustang equipped with automatic transmission. It comes with all items shown here.

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Used console lid catch. Plastic piece that screws to the underside lid of your late 1970-73 Mercury Cougar or 1970-78 Ford Mustang. Yep, used on Mustang II's, too.  Ford part number D0ZZ-63060A96-B and stamped into the plastic D0ZB-63060A96-B ...

Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull.  We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...

Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

New old stock deluxe shifter handle in black. Perfect condition, no cracks in the plastic. No release button or set screw included. NOS Fits 1967 Mercury Cougar XR7 and 1967 Ford Mustang with IDG or Interior Decor Group and all Shelby Mustangs with automatic. This one year only, T handle, has concave or recessed buttons.  Ford part number C7ZZ-7213-A. We know that Scott Drake is using this number for 4 speed manual knobs, which was a made up Ford part number on their part. We...

Grade B used deluxe shifter handle various colors. Please specify color in the notes, limited to stock on hand. Fair used condition will have at least one crack in the plastic. May also have slightly pitted chrome. No release button or set screw included. See related items for Grade A  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...

Good quality reproduction shifter assembly for all 1967-68 Mercury Cougar and Ford Mustang with consoles. NOTE: This assembly does not come with the lower bushing.

Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out our video on rebuilding your shifter below: ...

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

We rarely have extras of these in stock but we like to show these items so you know what you are looking for or you can use it as a visual and fabricate your own kit. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice.Also available as a reproduction mounting kit. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them. ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads.  3/8-24 threaded nut, serrated washer head style. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the course threaded nuts on the 1971-73 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

New black screw for attaching the black plastic automatic shifter bezel on any 1971-73 Mercury Cougar or Ford Mustang. Should also be for Mercury Comet and Ford Mavericks with floor shift automatic automobiles. #8 x 1/2 black pan head screw. Replaces Ford part # 52017-S2See related items for set of 4 screws as a kit. Check out our video on rebuilding your shifter below: ...

New black (set of 4) screws for attaching the black plastic automatic shifter bezel on any 1971-73 Mercury Cougar or Ford Mustang. Should also be for Mercury Comet and Ford Mavericks with floor shift automatic automobiles. #8 x 1/2 black pan head screw. Replaces Ford part # 52017-S2 Check out our video on rebuilding your shifter below: ...

Set of 4 new phillips oval head mounting screws with black finish for all 1967-68 Mercury Cougar automatic shifter bezel mounting plates without console and XR7-G bezels. Also fits 1965-68 Ford Mustangs with automatic transmissions and without consoles. Check out our video on rebuilding your shifter below: ...

Set of 4 screws for mounting the automatic shifter adapter plate on all 1967-68 Mercury Cougars without console. Also fits 1965-68 Ford Mustangs without console. Check out our video on rebuilding your shifter below: ...

Used to seal the Aluminum shifter housing to the transmission tunnel. Replaces Ford part #: C9ZZ-7370. Check out our video on rebuilding your shifter below: ...

We suggest using white lithium grease or petroleum jelly to ensure the seal will not stick to the shift lever. Fits 1969-73 Mercury Cougar and Ford Mustang, additionally it also fits 1971+ Maverick and Comet with floor shift automatic only.  If you have any side-to-side play in the shifter, this seal will not last. We do have the shifter bushings available. Replaces Ford part  numbers C9ZZ-7D351-A & D1ZZ-7D351-A. Get the matching mounting clips here. Check...

Replaces Ford part #: C5ZZ-7370. Check out our video on rebuilding your shifter below:

This plastic linkage rod / arm connects the floor shifter to the indicator light inside your console that illuminates the PRND21 on your illuminated console panel. Used on all automatic consoles 1967 -1968 XR7 and standard. Ford part number C7ZZ-7E148-A. Check out our video on rebuilding your shifter below: ...

This plastic linkage rod / arm connects the floor shifter to the indicator light inside your console that illuminates the PRND21 on your illuminated console panel. Used on all automatic consoles 1967 -1968 XR7 and standard. Ford part number C7ZZ-7E148-A. Check out our video on rebuilding your shifter below: ...

1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. These are used, and because of the low grade of chrome plating, these will show some form of light pitting.  handle, which is larger and has a faux leather covered handle in a variety of colors. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Tired of picking your broken button off the floor? This inserts in the left hand side of your deluxe (colored keyed) shift handle. Quality part made in China, please consider our good used units at half the price! 67 is actually a little different in contour but this will fit fine. Replaces Ford #: C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M and C5ZZ-7C488-D. Your buttons may have faded to gray after many years. These black buttons are injection molded plastic and have steel wear plates just like the originals. Technically this is a copy of the...

Black plastic selector button for all 1967 Mercury Cougar and 1965-67 Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M. Check out our video on rebuilding your shifter below: ...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Additionally it does not fit with the 1973 chromed T-handle without trimming.  Ford part C8ZZ-7C488-B.  Check out our video on rebuilding your shifter below: ...

Black plastic selector button for all 1973 Mercury Cougar and Ford Mustang with automatic transmission. It does not fit with the 1968-72 chromed T-handle.  Check out our video on rebuilding your shifter below: ...

Black plastic dummy button for all 1967 Mercury Cougar and 1965-67 Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-D.

Black plastic dummy button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Ford part C8ZZ-7C488-A.

This arm is attached to your automatic transmission floor shifter (see picture at left). Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for C-4 and C-6 transmissions. Ford part number C7ZZ-7302-A. ...

This arm is attached to your automatic transmission floor shifter (see picture at left). Fits all 1969-70 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for FMX and C-6 transmissions. Ford part number C9ZZ-7302-A. This part may have the course threads or fine threads. Normally this item ships with the course threads. We also stock the 1971-73 version that has a captured stud for...

This arm is attached to your automatic transmission floor shifter. Fits all 1969-73 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. This used part will come with a captured lower stud for attaching the shift rod as shown. Correct for FMX and C-6 transmissions. This version is found on 1972-73 cars, it has the captured lower stud for mounting the automatic shift rod to the transmission. Ford part number D1ZZ-7302-A. Check out our video on rebuilding...

It is as nice as it looks! Good fit. Replaces Ford Part #: C9ZZ-7E271-A Customer reviews: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked it up in a manual. That's customer...

Automatic shifter dial black background. This part screws to the shifter bucket, and sits under the pointer when everything is assembled in your shifter bucket assembly. Fits all 1969-73 Mercury Cougar and Ford Mustangs with automatic transmissions. Original Ford part number C9ZZ-7A213-A also can be D1ZZ-7A213-A. Check out our video on rebuilding your shifter below: ...

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This shifter dial was originally attached with heat to a pin connector. To reattach we suggest using glue. These look like it would be easy to detail the white letters for P R N D 2 1 with a careful hand. May have a chipped corner that is not seen when installed. Ford part # C7ZA-7A213A Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...