Windshield / Wipers / Washers

Used windshield support bracket for any 1971-73 Mercury Cougar or Ford Mustang. One per side, sold individually. Make sure that you have two of these installed prior to installing your windshield glass. The glass rests on these brackets and keeps glass from sagging. Ford service part number D2AB-65030A12-AA.

Pair on reproduction lower windshield stops for all 1969-70 Mercury Cougar and Ford Mustangs, all body styles. Includes two pedestals and the 4 screws as shown. 1969-70 front windshields are glued into the window channel, and must have these rests to keep the glass from sagging.  Replaces Ford part number C8AZ-6203012-A.

Replacement bellows for your 67-68 windshield washer foot pedal pump. Over the years, your original rubber might become brittle or worn down. This is all you may need to get your foot pump in great working condition again.

Good used windshield washer pump rubber hose assembly, fits 1967-68 Mercury Cougar and Ford Mustang. Hoses run from the foot actuated pump on the floor board, to the washer fluid bag, and to the washer nozzle 'T'. Includes firewall grommet, these are soft pliable hoses. Nozzle hose and 'T' kit also available new.

These zinc-plated Washer Nozzles are good copies of the originals. 1969 and 1970 Mercury Cougar and Ford Mustangs only. Sold in pairs. Replaces Ford Part C9ZZ-17603-A and D0ZZ-17603.

Plastic housings with brass nozzles. Note that you may need to adjust the nozzles to achieve the desired aim.

Economy version of the 67 - 68 washer bottle that has the incorrect "stepped down" design on the nipple and no FoMoCo Insignia. Comes with plain cap but we also have good used caps with Mercury Man logo which is correct for the Cougar here. You can find the washer bottle with the correct FoMoCo logo here. Replaces Ford part # C7OZ-17618-A. ...

This excellent reproduction windshield washer bottle includes the Ford logo on the lid (C9ZZ-17632-A) and part number C9ZF-17B613 stamped on the top of the bottle exactly like the originals. The tooling was made using the original Ford blueprints and nice original patterns. Blow Molded Plastic. There are two available reproductions, but this is the only version that is actually correct. NOTE: These reservoirs are not reproduced with the screens in the opening like the originals. Electric pump...

High quality rubberized vinyl bag, with Gold silk screened FoMoCo logo. An exact copy of the original unit. Only the early model 1967 Cougars would have used this, all other 67-68 Cougars would have used the plastic washer bottle. Replaces Ford Part # C1AZ-17618. According to Phil Parcells who runs the national data base for the Mercury Cougar, the changeover from the washer bag to the plastic bottle was approx Dec 1, 1966, at approximately consecutive unit # 545100. However there are oddball...

This is the bracket on which the windshield washer bag hang on the 1967 Mercury Cougar.  According to Phil Parcells, who runs the natioanl data base for the Mercury Cougar, the changeover from the washer bag to the plastic bottle was approx Dec 1, 1966, at approximately consecutive unit # 545100. However there are oddball reports of bags after this date, but it is unclear if these are possibly collision repairs,

These zinc-plated Washer Nozzles are exact copies of the originals. Sold in pairs. Replaces Ford Part #: C7ZZ-17603-A.

This is a replica white plastic washer bottle / reservoir with black top & cap (D1TZ-17632-A), just like the original. This washer bottle is made using the original Ford blueprints.  Electric pump sold separate (see related items).  Replaces Ford part #: D1TZ-17618-A / D1TZ-17618-B.

Injection molded high strength plastic connector for hoses leading to nozzles. Factory fit. Replaces Ford Part #: C7SZ-17A601-A or C0AB-17A601-A. Will not fit 69-70 with factory hoses as they used Ford part # C8OZ-17A601-A, which had larger outlet nipples.

Injection molded high strength plastic connector for hoses leading to nozzles. Correct squared press-in fitting, unlike some rounded reproductions. Replaces Ford Part #: D1ZZ-17A601-A.

NEW DESIGN... The consistency of rubber on these strips is soft and supple now.   The doors do not have to be "slammed"   Of the three reproductions versions out, there these are the best.    If you have any NOS to sell we would like to hear about them. Replaces Ford part #: C9ZZ-7602626

NEW DESIGN... The consistency of rubber on these strips is soft and supple now. The doors do not have to be "slammed" Of the three reproductions versions out there, these are the best. If you have any NOS to sell we would like to hear about them. Replaces Ford part #: C9ZZ-7602627

Original driver side (left hand) wiper arm pulled from a 71 - 73 mercury Cougar. Includes snap clip to hold the second arm in place. Replaces Ford part #: D1ZZ-17526-B. Note: 1971 model year through 11/15/1970 uses the same wiper arm on both sides, which is the one used on the passenger side in the late 71 - 73 Cougars (Part #: D1ZZ-17526-A).

Original passenger side (right hand) wiper arm pulled off a 71 - 73 Mercury Cougar. Replaces Ford part #: D1ZZ-17526-A. Note: 1971 model year through 11/15/1970 uses the same wiper arm on both sides, which is the one used on the passenger side in the late 71 - 73 Cougars (Ford part #: D1ZZ-17526-A).

Satin Finish Wiper Arm

These are hand picked grade A condition original arms with no defects. Right is the same as left. Sold individually, two per car. The reproductions of the 67 - 70 are identical, but the originals are NOT! The 67 - 68 and the 69 - 70 were bent at different angles and carry different Trico patent numbers. In our experience in owning and parting 100's of early Cougars, 1967 and 1968 use the early style, and 1969 and 70 use the later style. Click here to see pics of the differences between the 67...

Reproduction wiper arms for the 71 - 73 Cougar or Mustang. Sold as a pair.Replaces For Part number D1ZZ-17526-B

These are hand picked grade A condition original arms with no defects. Right is the same as left. Sold individually, two per car. The reproductions of the 67-70 are identical, but the originals are not the same between years. The 67-68 and the 69-70 were bent at different angles and carry different Trico patent numbers. In our experience in owning and parting 100's of early Cougars, 1967 and 1968 use the early style, and 1969 and 70 use the later style.Click here to see pics of the...

Exact reproduction of original. Original manufacturer has redesigned blade assembly with plastic components. Sold individually, includes one wiper blade assembly and one rubber blade. Fits the 67 and 68 Mercury Cougar. Replaces Ford part #: C3AZ-17528.

Original stainless steel wiper assembly, fits any 1967-68 Mercury Cougar or Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 15" rubber wiper blade not included.Replaces Ford part #: C3AZ-17528-J.

Best replacement for the original wiper blade assembly. Replaces Ford part #: D4AZ-17528 and C9AZ-17528-A. Sold individually, includes one wiper blade assembly and one rubber blade. Fit the 69 and 70 Mercury Cougar.Thanks for the plug Mark!: My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other and measure a cross...

Original black windshield wiper blade holder. Fits any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, two per car, 18" rubber wiper blade not included.Replaces Ford part #: D1AZ-17528-C or D3AZ-17528-A.

Original Trico stainless wiper holder assembly, removed from a 1970 Mercury Cougar. Fits any 1969-70 Mercury Cougar and Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 16" rubber wiper blade not included.*Note - This is NOT, repeat NOT the ultra rare 1969 production wiper blade holder assembly. This is a Trico 16 inch blade holder as found on most 1970 cars.

Original FoMoCo used two speed windshield wiper motor for your 1967-68 Mercury Cougar or Ford Mustang. This used motor comes as shown with wiring harness for all 1967-68 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1967-68 installation, must be marked 7Z. Linkage arms sold separately. Ford part #s C7ZF-17504-D.

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem, this part is the culprit! To test if your unit is worn grasp the driver side wiper arm and move the arm back and forth gently. If the passenger arm does not react to your every movement this assembly needs to be replaced. It is an easy to replace part in that you can remove the cowl panel behind your...

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem, this part is the culprit! To test if your unit is worn grasp the driver side wiper arm and move the arm back and forth gently. If the passenger arm does not react to your every movement this assembly needs to be replaced. It is an easy to replace part in that you can remove the cowl panel behind your...

This Wiper Pivot To Cowl Seal Reproduction is sold as a pair. Fits both the 67 and 68. Replaces Ford part #: C5ZZ-17475.

Original FoMoCo used two speed windshield wiper motor for your 1969-70 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness with unique grommet for the firewall specific to 1969-70 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1969-70 installation, must be marked 9Z. Linkage arms sold separately. Ford part # C9ZF-17504-C.

Original FoMoCo used two speed windshield wiper motor for your 1971-73 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness, for all 1971-73 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1971-73 installation, must be marked 1Z. Linkage arms sold separately. Ford part #s D1ZF-17504, D2ZF-17504, D1ZZ-17508-A

This is the set of six bolts needed to attach the pivot section of the wiper arms to the cowl on 1969-1970 Cougars and Mustangs. Three bolts needed per side, six per car.

This is an exact reproduction of the wiper transmissions that will connect to the wiper motor and the output shafts. It includes correct links and pivots for full range of motion. This is commonly replaced when swapping your cowl panel, steel dash panel, and/or firewall. Also a good idea if your wiper arms are not making a full rotation.

Used wiper transmissions that will connect to the wiper motor and the output shafts. This is commonly replaced when swapping your cowl panel, steel dash panel, and/or firewall. If you want to keep your car original, go with these good used arms, or you can find the reproductions here.

Nice reproduction of the D0OZ-17C583-A windshield wiper stop as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Zinc plated and rubber dipped like OEM Ford. Replaces Ford part number D0OZ-17C583-A.

Used wiring pigtail that runs from the 14401 main under dash wiring harness to the wiper motor.

Electrical wiring pigtail for the windshield wiper motors on any 71 - 73 Mercury Cougar or Ford Mustang. Plug with correct color wires and an adequate amount of wire length to make a repair or splice onto the newer motors without plugs.

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall, look for two dimples. Wiring is simple, unplug the windshield wiper harness and plug the male and female ends into the appropriate plugs on the controller. Sometimes called interval or delay wipers.*NOTE* Must be used in conjunction with a intermittent wiper delay switch.Part # C9ZB-17C476, MPC #'s C9ZZ-17C476-B or D0ZZ-17C476-B.

Easy to install kit that converts your two speed wiper system to a variable speed system. These "off shore" units are spotty at best. We recommend our good used unit which you can get right here.

Rare find in NOS form! Used only on the 1967 and 1968 Mercury.Ford part number C7AZ-17632-A

Used spacer for the lower windshield moulding, also called an 'anti rattler'. 4 of these plastic pieces were used per car. These spacers were originally installed in the four cutouts in the 1967-68 lower windshield moulding. We won't always have these in stock due to the low survival rate of these spacers. Sold individually.Replaces Ford part # C7ZZ-6503150-A. 

Original NOS part, new in box. Ford part # C5ZZ-6503110-A

This is a good used fitting with large and small nipples for use with the foot actuated washer pumps found on 1967-68 Mercury Cougar and Ford Mustang. Good used part that we verify the check valve is working. These screw into of the rubber covered pumps.