Dash Knobs, Buttons & Related Hardware

Reproduction headlight switch knob for the 71 - 73 Cougar.

Don't be fooled by knobs with similar part numbers, they have longer shafts and will not work as well on your Mercury Cougar or Ford Mustang application.Ford part # D1ZZ-18830-A, and Ford casting # D1ZA-18A932-AA.*TRIVIA* Did you know that Ford called the inner (balance / tone) radio knobs "discs?"

This is one of the easier knobs to find in that it does not break easily and can be found on many 1967 FoMoCo products. Not used on Cougars with a center console and little to no differences can be seen between the different examples. One explanation for having multiple casting numbers for the same part is that Ford would use multiple suppliers for a single part. To differentiate which part came from which vendor, different casting numbers would be assigned. If there was a problem with a run...

Reproduction inner radio knob used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

Rare plastic radio knob used only with the 1967 XR7 and standard Cougar console. This knob differs from the Mustang console and Cougar / Mustang non console knob in that it is deeper to clear the console pad unique to the 1967 Cougar. Ford called these rare little units "discs" back in the day Replaces part # C7WA-18A932-A

Used on early non console 1967 models and has a lower profile than the later version. We also have pitted knobs we can throw in on a order for free, just mention it if all you need is a knob that gets the job done.Ford part # C7MA-18817-A.

Unlike the plastic console knobs, the issue with these metal knobs is pitting as opposed to breaking. Very hard to find in clean condition.Replaces part # C7ZA-18817

Rare radio knob used only on the 1967 XR7 and standard Cougar console. This knob differs from the Mustang console and Cougar / Mustang non console knob in that it is deeper to clear the console pad that is unique to the 1967 Mercury Cougar. Early standard model Cougars with the console used a more petite version of this plastic knob. Replaces part # C7WA-18817-B

Used wiper knob for any 1967 Mercury Cougar. This version is smaller than the 1968 knob. Unlike the 1968 version, there is no set screw, and is simply pressed into place. You may need to use a bit of adhesive to hold in place. Good condition, will have a small rust pit or two.

Used knob for wiper control switch on dash panel. Constructed of metal with chrome, may show some wear on the black painted section and flaws in the plating.Ford part number C9ZZ-17513-C.

Used wiper control knob for lower dash. Plastic knob, will show some minor wear. Ford part number D0OZ-17513-A.

Chrome and black knob just like the original.NOTE: This knob is correct for 1969. It will fit on a 1970, however the orientation of the pointer will be off. You can find a good used 70 knob here. Replaces Ford Part # : C9ZZ-17513

This knob set differs from the set used later in 1967 only in that the outer knob has a lower profile head. Keep in mind we have reproduction knobs that will work in place of these.

This set of reproduction used knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear...

Full set of metal radio knobs for the 1967 Mustang or Cougar. Not for use with the 1967 Cougars equipped with factory center console. Keep in mind we have reproduction knobs that will work in place of these.

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

The early Cougars had a lower profile head on the outer knob. It is assumed they beefed up the design in early in the year because the knobs were easily broken. These delicate plastic knobs are very hard to find in this condition. Only the utmost purist would care to obtain a trivial detail part such as these to make their car correct. These deeper knobs were only used in cars equipped with a factory center console. The Mustangs did not have a padded console in 1967 so this set is for 1967...

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

Reproduction nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. Replaces Ford part number C9ZZ-11650-A .

Nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. These are used, and usually will have small blemishes. All will have good threads and chrome plating on the face.Ford part number C9ZZ-11650-A .

Used bezel retaining nut for the headlight switch on any 1971-73 Mercury Cougar or 1971-72Ford Mustang. These are much better quality than those found in the 1969-70 cars. Good threads and very good chrome on the front as shown. Check the length for the 1973 Ford Mustang, we've had an owner that found one to be over 2 inches in length. Unfortunately, we do not have the longer length version.Replaces Ford part number D1ZB-11650-BA.

C7WB-13753-A Grade-A used screw on nut or bezel for the dash toggle switches on 1967-68 Mercury Cougar XR-7, 1971-73 Mercury Cougar, and 1969-70 Mustang Shelby console switches. This is a perfect used part, if you need an average quality used one mention it when you make your order and we will try and locate a free one for you.

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

If you look close at our used set I do not think you could tell the difference, look at the back side in comparison to used and you will see a noticeable difference. *NOTE* The fifth part slips into the backside of the inner knob on the passenger side and acts as a spacer for Cougars or Mustangs without the rear fader option. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. ...

Note: Not for use with aftermarket radios. Finding correct radio knobs for a 1968 Ford Mustang or Mercury Cougar equipped with a center console has been a huge obstacle for decades now. To clear the padded radio bezel cover, one must have these elusive, one year only, deep well knobs. These will also work on 1967 Cougar with console and although they would not be letter correct for anything but a 68 with a console, they do not look out of place on a 67 with console. Note that this four piece...

This is a radio nut removal tool used to remove the radio shaft nuts. No more trying to remove those little units with the wrong tools and potentially damaging your bezel or dash. These are made from HRS steel and are milled to fit the shaft nut perfectly.

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used steel rear retaining bracket for the headlight switch on any 1971-73 Mercury Cougar or Ford Mustang. These are bare steel and will have a bit of flash rust as shown, nothing serious. Replaces Ford part number D1ZB-13B107-AC.

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. Ford part numbers: DOZZ-17C491-A, D0ZB-17C491-A.

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. 1969 has the flat spot oriented at the bottom. Ford part numbers: C9ZZ-17C491-A, C9ZB-17C491-A.

Used steel rear retaining bracket for the windshield wiper switch and cigar lighter on any 1971-73 Mercury Cougar or Ford Mustang. These are bare steel and will have a bit of flash rust as shown, nothing serious. Replaces Ford part number D1ZB-17C584-AC.

New Old Stock 1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was used and the surrounding bezel would be labeled "Top" or "Defog" in the farthest position to the right. The fourth switch is never used on the 1969 xr7, it is just there to...

1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. Switches sold pit free on the chrome. Switches guaranteed to work, but are likely stiff. Electro solvent usually helps with that sticking condition, see product label for directions prior to use. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was...

C7WB-13713-A New old stock XR-7 dash toggle switch for the "Panel" light on the 1967-68 Cougar. This switch has the black plug, and it will work for the "Courtesy" light switch too, those are typically have red plugs though.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1969 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

This is a bezel nut tool used to remove the toggle switch bezel nuts on 67 - 68 & 71 - 73 XR7 Mercury Cougars. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This is a MUST HAVE if you are replacing a toggle switch or taking apart your dash, we use this tool in our shop all the time and love it!

Good original used toggle tip for the 1971 - 1973 Mercury Cougar XR7

These are ready to ship now! Sold in a set of four. Specific to 1967 XR-7.There are three versions of shafts used on the 1967 - 1968 XR7 dash toggle switches and all three feature the same C7WB-13713-B engineering number. There is a 1967 switch with a large shaft, 1968 with smaller shaft and 1968 with a small shaft that has been milled down on two sides. The reason Ford decreased the size of shaft in 1968 was to enlarge the thickness of the plastic on the toggle tips. By decreasing the size of...

The 1968 toggle tips we sell fit very tight at best.  To make them fit you will have to remove every bit of glue residue left from the old tips and you may even have to enlarge the holes in the plastic by boring them out a little with a drill bit.  Do not put excessive force on the shaft as you may damage the switch internally.  We apologize for the fit but once on you will have an attractive durable set of tips in place.  No returns on these although if you happen to...

Used under dash ashtray assembly for non-console 1970 Mercury Cougar and Ford Mustang. Pebble grain finish that you paint to match your interior color. Comes as shown with light.

Used under dash ashtray assembly for 1969 Mercury Cougar XR7 models. Same as the standard model ashtray, but has burl wood and chrome. Does not come with cigar lighter or knob. Light and wiring harness NOT included.Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

Knob for the under dash ashtray on 1969 Mercury Cougar and Ford Mustang without consoles. Used in conjunction with a chromed bezel. Ford part # C9ZZ-65048B38-A.

Bezel for the knob for opening the under dash ashtray on 1969 Mercury Cougar and Ford Mustang without consoles.