Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 
Filter Products by


Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 433-480 of 1849
$0 Price: $10.75

Buy Details

Availability: In-Stock Item
Item #: 16189 -

Exhaust manifold flange rings or 'doughnuts' for stock cast iron 428CJ exhaust manifolds. These are the malleable type that conform and slightly crush. Inside diameter just over 2-1/8 inches. Sold individually, two needed per car.

$0 Price: $13.37

Buy Details

Availability: In-Stock Item
Item #: 31959 -

Round hood latch dowel that screws into the hood on all 1967-68 Mercury Cougars. Threads are 1/2-13, dowel assembly includes threaded dowel, jamb nut and washer as shown.Fits many other Ford products, see list below.Replaces Ford part numbers C4ZB-16929 and C5ZZ-16929-A.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27506 -

Round hood latch dowel that screws into the hood on all 1967-68 Mercury Cougars. Threads are 1/2-13, dowel assembly includes threaded dowel, jamb nut and washer as shown.Fits many other Ford products, see list below.Replaces Ford part numbers C4ZB-16929 and C5ZZ-16929-A.

MSRP:$15.00
$15.00 Price: $10.05

Buy Details

Availability: In-Stock Item
Item #: 41795 -

This A/C evaporator drain hose is molded flex hose similar to the original, but it will need to be cut to the proper length. It is correct for 67 - 68 but can be made to work on 69 - 73. Replaces Ford part #: C7ZZ-19858-C or C8TZ-19858-A.

$0 Price: $20.05

Buy Details

Availability: Out of Stock
Item #: 11784 -

Reproduction power steering drop bracket for the Mercury Cougar or Ford Mustang. One must use this part when installing headers with power steering.  Because of the way this bracket hangs down, it will get bumped and bumped hard in time. Becasue of this we recommend considerning our premuim version of this bracket, as it is substantially stronger.

$0 Price: $18.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0072 -

Used fresh air vent duct found behind the driver side dash panel of all 1971-73 Mercury Cougar without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1WY-6501878-A.

$0 Price: $19.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0130 -

Used center vent connector or duct tube. Fits 1969-70 Mercury Cougar with factory or integral air conditioning. This attaches to the center register in the dash pad. Replaces Ford part number C9WA-19B737-A or C, and C9WY-19B680-B.*Note - Will not fit Ford Mustang.

$0 Price: $24.17

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32090 -

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

$0 Price: $22.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0343 -

Used rubber elbow that vents air to the blower motor on most 1967 Mercury Cougar and Ford Mustangs with factory air conditioning. At some point in time, this elbow design changed. Easy to tell, this early style connects to a nipple on the fan blower motor. The later version has a hole in the motor case. Not needed with reproduction fan motors, they don't even have the hole. Replaces Ford part number C7ZA-19A786-A.

$0 Price: $21.45

Buy Details

Availability: In-Stock Item
Item #: 42067 -

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

$0 Price: $15.95

Buy Details

Availability: In-Stock Item
Item #: 42066 -

These beautiful reproductions replace those rusty and corroded originals that just look nasty. 5/8" Replaces Ford Part #: C6AZ-18599-B

$0 Price: $15.95

Buy Details

Availability: In-Stock Item
Item #: 42068 -

These beautiful reproductions replace rusty and corroded originals that just look nasty.5/8" Replaces Ford Part #: C6AZ-18599-S

$0 Price: $20.05

Buy Details

Availability: In-Stock Item
Item #: 42047 -

Reproduction water inlet elbow for your 1968 big block Cougar or Mustang.Replaces Ford Part #: C8AZ-18599-AClick on images to enlarge. ...

$0 Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 25888 -

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

$0 Price: $20.57

Buy Details

Availability: In-Stock Item
Item #: 25882 -

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

$0 Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 25886 -

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

MSRP:$29.99
$29.99 Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 26069 -

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

MSRP:$29.85
$29.85 Price: $22.86

Buy Details

Availability: Out of Stock
Item #: 20379 -

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

$0 Price: $24.89

Buy Details

Availability: Out of Stock
Item #: 24104 -

Used Driver Side / Right Side Fender Extension Emblem for the 1967 and 1968 Mercury Cougar

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33527 -

Used Grade B 3 1/2" XR7 center cap emblem was used on the Mercury Cougar XR7 hubcap / wheel cover. 

$0 Price: $24.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 20357 -

Two required per car, right is the same as left. Good used Cougar emblem with no pits, deep scratches or broken studs.

$0 Price: $24.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19440 -

Used COUGAR Script Quarter Panel Emblem for the 1969 and 1970 Mercury Cougar

$0 Price: $12.47

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 21-0122 -

These always are peeling. Located on the right side on the dash face...

$0 Price: $23.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24185 -

Good used "C" pillar emblem for your XR7 with no obvious pitting. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.Ford part number C7WY-6528818-B1 Hi Don: Thank you for fixing me up with the XR-7 pillar emblems. I appreciate doing business with you. It's nice doing business with guys who are not perfect, but try to be and correct anything within reason that is called to their attention. Take care, Greg Worth TN ...

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12814 -

Poor chrome, for use as a core to be restored.

$0 Price: $17.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24098 -

Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only designed to be installed once. Click on images to enlarge. The above is a very sought after collectible that was circulated back in 1967-1968. This picture above (From Jim Pinkerton) is of a pen...

$0 Price: $18.85

Buy Details

Availability: In-Stock Item
Item #: 26448 -

This grille background piece requires you remove your Cougar emblem before installing. To remove the cat emblem you will need to grind from the backside and epoxy the emblem back in place after-wards. Vast improvement over your current faded, dinged part. Not for use on the xr7. ...

$16.90 Price: $18.77

Buy Details

Availability: In-Stock Item
Item #: 41997 -

Reproduction steel emergency / parking brake adjustment rod for the Mercury Cougar or Ford Mustang and is threaded for full adjustability. Replaces Ford Part # C7ZZ-2628-B.

$0 Price: $12.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12278 -

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.

$0 Price: $24.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12277 -

This is the first bracket to secure the emergency brake cable as it exits the firewall. It mounts to the frame rail. It is held on by one bolt which is not included, picture is for reference only. Part will have rust but not severe.

$0 Price: $11.00

Buy Details

Availability: In-Stock Item
Item #: 16137 -

New emergency flasher can for all 1969-73 Mercury Cougars. Not to be confused with the turn signal flasher canister, those are rated differently. 

$0 Price: $13.25

Buy Details

Availability: In-Stock Item
Item #: 26089 -

Easy screw in replacement with correct chrome finish. Made in chrome die-cast, originals were plastic. The tilt column switch uses a deeper stem. Replaces Ford Part #: C7OZ-17513-A

$0 Price: $14.27

Buy Details

Availability: In-Stock Item
Item #: 26560 -

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

$0 Price: $15.17

Buy Details

Availability: Out of Stock
Item #: 26727 -

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

$0 Price: $21.85

Buy Details

Availability: Out of Stock
Item #: 14-0050 -

New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP138 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...

$0 Price: $16.36

Buy Details

Availability: In-Stock Item
Item #: 26079 -

Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302

$0 Price: $14.45

Buy Details

Availability: In-Stock Item
Item #: 41996 -

This reproduction emergency / parking brake equalizer lever is made from heavy gauge stamped steel and is a quality reproduction. Replaces Ford part # C7ZZ-2A605-A.

$0 Price: $13.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30058 -

Used emergency / parking brake equalizer lever. Good used part, fits any 1967-68 Mercury Cougar or Ford Mustang. Part was cleaned for the photograph. Most all of our levers come from Cougars, typically they have a generous amount of under coating that partially covers these levers and protects them. In other words, as they come off of the cars.Replaces Ford part # C7ZZ-2A605-A.

$0 Price: $19.65

Buy Details

Availability: Out of Stock
Item #: 14191 -

Very nice reproduction of the drivers side muffler hanger as found on 1970 - 1973 Mercury Cougar and Ford Mustang. Every thing looks correct, riveted rubber and stamped steel brackets as original. You can hang up to a 3 inch pipe with this unit.

$0 Price: $19.65

Buy Details

Availability: Out of Stock
Item #: 14189 -

Reproduction OEM style passenger side (right hand) exhaust hanger for the Mercury Cougar or Ford Mustang. You can hang up to a 3 inch diameter pipe with this unit.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0392 -

Driver side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Driver side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530057-A.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0391 -

Passenger side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Passenger side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530056-A.

$0 Price: $21.85

Buy Details

Availability: In-Stock Item
Item #: 26749 -

This eyelet bushing is made from higher grade rubber and unlike the NOS and other reproductions has a solid center shaft. The center shaft of this reproduction is a flat piece of steel that is bent into a circle to make the shaft for the eyelet bolt to go through, just like NOS.  Two per car, these are used on one end of the leaf springs and the shackles are used at the other end. Replaces Ford Part #: C7WY-5781-A, C4DZ-5781-C, C5ZZ-5781-A, D3ZZ-5781-B. ...

$0 Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 12335 -

New clear plastic lens or face plate for the heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!

$0 Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 13084 -

New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...