Heater with Air Conditioning & Air Conditioning Components

Seals the hole where the A/C lines pass through the core support on the driver side on Mercury Cougars and Ford Mustangs. Replaces Ford part #: C7ZZ-19810.

This replica tag is of a lower quality than the originals were. The aluminum stock from which this Mercury Cougar A/C tag is made, is about half the thickness of original and the font, instead of being white, is unpainted aluminum. This is a cheap looking, and feeling, part compared to the original. We do have the clip that holds it in place. Check out the product images for an example of factory placement for this tag.

New components used in this harness and not included with main underdash harness. This sub-harness is needed when installing factory in-dash A/C in your Mercury Cougar or Ford Mustang. Even though this picture shows a purple wire, the one that attaches to the back on the starter switch, the part you get will sometimes have a black wire in its place. Keep in mind we also have mint used available. Replaces Ford Part #: C7ZZ-19800-A, tag found on original wires will read C7ZB-19945-A. ...

Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. There are a couple of versions of this housing. There is a version with a cooling nipple for cooling the...

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. 

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version. There are a couple of versions of this housing. There is a version with a...

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Air conditioning fan blower assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Air conditioning fan blower assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Reproduction black center A/C vent for the 67 - 68 Mustang.

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

New manufactured air conditioning condenser for any 1971-73 Mercury Cougar or Ford Mustang. Condenser only, you will need to re-use or purchase a new dryer and possibly other components. 

Vacuum switch not included. This control switch lever assembly only, for the vacuum and damper door consists of the two lever assembly for the vacuum and cable actuation of the A/C plenums damper doors on Mercury Cougar and Ford Mustang with integral A/C.Ford part # C7ZZ-19B888-A.

Used air conditioning connecting duct or manifold. This plastic manifold mounts behind the center dash vent. Ford calls it a 'duct and connecting assembly' or 'A/C junction'. Grade 'A' condition, ships without cracks, splits, or broken tabs. Original factory or 'integral' air conditioning part.Ford part number D1ZZ-19C932-A.

Redesigned modern evaporator has 35% MORE PASSES, using three-circuits, instead of the original single-circuit design. This is a direct bolt-in replacement and requires no modification.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal. It has been our experience that these often fail within a few years. We suggest flushing and pressure...

Reproduction A/C evaporator for your Mercury Cougar or Ford Mustang.*Note - We have had numerous customers complain that these don't fit exactly like the originals.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal, which also equals out to performance that's sub-par to a good used original evaporator.Click on images to enlarge. ...

Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what...

Used air conditioning evaporator core, for most of the 1969 model year and all of 1970. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have...

Used air conditioning evaporator core, for most of the 1969 model year. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a...

Used air conditioning evaporator core for 1971-73. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what kind of labor is required to install one of these. 1971-73 evaporators have 2 male fillings, and the whole unit is made of aluminum, including the tubes.Ford part #...

Exact replacement to original drier that removes moisture and should be changed anytime system is recharged. It really is the life of your system. This stainless steel filter element stops contaminants from clogging the expansion valve.

Exact replacement for your original dryer and should be changed anytime the system is recharged. This stainless steel filter element is the life of your system and stops contaminants from clogging the expansion valve. Painted the correct satin black.

Exact replacement to original dryer. Drier removes moisture and should be changed anytime system is recharged. It is the life of your system. Stainless steel filter element. Filter stops contaminants from clogging expansion valve. Replaces part # C9ZZ-19959-A.

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade A vents will not have any cracks or breaks.

Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Nice fit, made of plastic. Will work with or without console, has slightly wider wings for clearance of the rear of the factory installed consoles.

Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade A vents will not have any cracks or breaks.

Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade B vents will have a small crack or break usually around the mounting holes, but will not effect it's functionality.

Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs without a console.

This unit is a reproduction concours correct A/C discharge hose for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

High quality and correct looking air conditioning discharge hose for Mercury Cougars or Ford Mustangs. This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, C7ZA-19972-E is the correct part number. This hose is approximately 20 inches long. Two different crimped ends, smooth and waffle may be the difference between Dearborn and San Jose or 1967 and 1968. Anyone know?The Ford MPC number is C7AZ-19972-A.

Regardless of which V-8 engine, C9ZA-19972-C or C9ZA-19972-E, both are the correct part number. This hose is approximately 20 inches long. Ford part # C9ZZ-19972-C.

Regardless of which V-8 engine, D1ZA-19972-AA or D1ZA-19972-AB part number. This hose is approximately 24 inches long. These used hoses probably still hold pressure, we suggest a purchase of new 'O' rings prior to installation.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine from 1969-73. Original condensation drain hose from the A/C case, through the floor board, to the ground. Replaces Ford part # C9ZZ-19858-C.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Ford part # C9ZZ-19858-C.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Almost the same hose as was used 1969-70, Dearborn assembly line hoses have a ribbed section 1971-73. The 1969-70 versions, typically have the alligator texture on the outside of the hose.  Ford part # C9ZZ-19858. ...

Regardless of which V-8 engine, C7ZA-19835-A or C7ZA-19837-D both can be the correct part number. This hose is approximately 74 inches long and this line also incorporates the site glass. The Ford MPC # is C7OZ-19837-A.

Regardless of which V-8 engine, C8ZA-19835-A or C8ZA-19837-A both can be the correct part number. This hose is approximately 74 inches long. This hose also incorporates the site glass. The Ford MPC # is C8ZA-19835-A or C8ZA-19837-A.

Regardless of which V-8 engine, C9ZA-19837-A or C9ZA-19837-C both are the correct part number. This hose is approximately 68 inches long. Ford part # C9AZ-19837-A.

Click on images to enlarge. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342). One of the major differences between the reproduction and the original sight glass hoses, is that the texture of the originals was much more defined.  You can see and feel the ridges in the hose on the originals.  Below is a close up picture of repro and used side by side, and it is obvious that the repro is not nearly as textured as the originals...

Good used hose that connects the sight glass hose to the Air Conditioning Dryer. Includes the sight glass to dryer hose (Ford Part # D1ZA-19835-A), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252).

Concours correct and constructed in original Ford style black thermoplastic material with a nylon barrier. This hose assembly is built to be compliant for R-12 or 134a refrigerants.NOTE: We have three hoses from a previous supplier that we have available for about half the price. The only difference would be that instead of the thermoplastic material, these are the standard rubber type hoses. Pick one up here. ...

High quality and correct looking air conditioning suction hose for the Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, C7ZA-19867-C is the correct part number. This hose is approximately 55 inches long.Ford MPC part # C7ZA-19867-C.