Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...
C7AZ-6571-B
C6OZ-7A533-C. Clutch Pedal Rod To Firewall Seal. Much better than repro. Also fits 1966 Mustang / Fairlane / Comet and others.
Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim,...
These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in...
New carburetor gasket for all 289-4V, 302-4V, and 351-4V, Mercury and Ford cars from 1964-1970. Same gasket used between intake manifold and spacer, and spacer and carburetor. Sold individually, 2 required for complete installation with Ford 1 inch factory spacer and correct numbered Autolite...
New 390 2BBL Carburetor spacer gasket for the 1968 X code 390-2V engine. Two needed per installation, one on both sides of the spacer plate.
New carburetor gasket for most 1967-73 2 barrel carburetors. 289/302/351W/351C engines. Replaces Ford Part #: C3AZ-9447-B *Excludes 1968 X code 390-2V premium fuel engines.
New carburetor gasket for 67 - 70 Cougar or Mustang with 390 or 428 cobra jet engines and Ford numbered Holley carburetors. One or two needed per installation (with or without spacer plate) sold individually.
Made from fuel resistant cork like original. Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt,...
Comes with attaching staples made of stainless steel. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. Replaces Ford part #: C4DZ-16238.Not all cars were assembled with this seal, some came with staples, and others...
Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you...
Reproduction Clutch Pedal Rod To Firewall Seal. Replaces Ford Part #: C6OZ-7533.*NOTE* From personal experience we have found these do not stay attached to the firewall as well as the originals. An adhesive will remedy this problem.
For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.
This Steering Box Cover Gasket Reproduction fits the 67, 68, 69, and 70. Replaces Ford part #: C3DZ-3581. If your original steering box is one of the few that is still tight then you will want to open it up, clean out all the decades old solidified grease and put new grease in.
Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.
If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.
Due to the vulnerable location of the control valve these often get cracked or worn through from rubbing on other components. Fits most all Ford passenger cars 1962-1970. Replaces Ford part number C2AZ-3C705-B
This Lower Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73. Replaces Ford part # C7OZ-3105-A.Just and FYI, in order to install this boot, the entire lower ball joint must be removed from the lower control arm. That means grinding or drilling out the rivets, or removing...
This Upper Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73.Replaces Ford part #: C7OZ-3105-B.*Installation tip - The inside diameter of the grommet is just a hair too small to properly fit on the stud. Restoration expert and MCA Judge Marcus Anghel, suggests using a...
Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.
Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.
Rubber valve cover gaskets for any FE 390 or 428 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.
Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...
Replaces Ford part # C5ZZ-9673. Fits 1967 289 and 68 -70 390 - 428 cars without Ram Air (C8ZZ-9673).
Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.
Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.
OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.
OEM Style Oil Pan Gasket.
Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.
Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098
Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.
Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the...
This gasket seals the fresh air tube in the cowl to the heater box inlet on 1967 through 1970 Cougars.
Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.
[No Description Provided]
CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber, and the rubber to the window channel. Non hardening and stays pliable, 1/10th of a gallon. You will...
Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A. ...
Reproduction gasket for the vintage two piece Carter fuel pump bowl for the Mercury Cougar or Ford Mustang equipped with either the 390-4V, 427-4V or 428CJ engine.
Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.
New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.
New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.
New timing cover gasket set for 1967-70 Mercury Cougar and most all Fords with 289/302/351W engines. Gasket set includes; timing cover gasket, crankshaft seal, water pump gasket for early or late water pumps, and the oil pan corner gaskets under the timing cover.
Here is our free download for the 1968 Mercury Cougar sunroof panel service procedures.
Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and...
Rubber Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.
New water pump plate gasket for the Mercury Cougar or Ford Mustang.
Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits...
Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top...
Wheel seal for both front disc and front drums, 1967-73 Mercury Cougar and 1967-73 Ford Mustang with V-8. Seals sold individually. Two of these are needed, one for each side on the front.
New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water...
Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!
New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.
New thread sealant specially formulated to seal liquid in high temperature applications.
New RTV oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula...
Repro fuel pump gasket for 1967 - 1970 Cougars or Mustangs with 289/302/351W/390/428CJ engines.
New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1967-70 big block Ford engines with size 390, 427, or 428 cubic inches, FE engine only. 1967-70 Mercury Cougar, Ford and Ford Mustang.
When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel. These are not technically manufactured to fit the Cougar / Mustang, however these are very close to...
Permatex Ultra Copper Sensor Safe High temperature silicone, good for any makes and years. This stuff won't harm your Oxygen Sensors, and is good for up to 700 degrees intermittent.
Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two...
This is the original JB Weld. We decided to bring this stuff in as a convenience to you, our customers. Why not buy a pack so that the next time you need to bond something together, you'll have a couple of tubes handy? No need to get up and go to the hardware store. With just a few clicks of your...
New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.
Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered...
Reproduction lower ball joint retainer and gasket. Works on 67 - 73 Cougars and Mustangs.
UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The...
Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang.
If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our...
Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.
Partially dipped clip for attaching the seal on top of the radiator core supports. Often times with air conditioning the seals were installed. The factory sometimes used staples, sometimes clips. You would have to investigate your core support for staple holes. 5 clips are typical for attaching...
Partially dipped clip for attaching the fuel line harness or trunk wiring harness, or fuel line at fuel tank. Found in various places on 1967-70 Mercury Cougar and Ford Mustang.
This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone...
Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal.
Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal.
Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions.
Cork pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Rubber gasket also available.
Rubber pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Cork gasket also available.
Basic C6 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C6 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that U code C-6 transmission. Quality kit, same as supplied to professional shops. Big and small block...
O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.
Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available. NOS power steering control valve repair kit. Ford part number C2AZ-3A553-A. ...
New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A. ...
New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A. ...
Top Loader transmission input shaft seal, small shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University.*Note -...
Top Loader transmission rear seal, big shaft 31 splines, 428CJ, 429CJ, and Boss 429 only. Quality Timken part. Fits 4 speed Top Loader Ford transmissions 1968-71 Mercury Cougar and 1968-71 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University. ...
Top Loader transmission rear seal, 28 splined shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University. *Note -...
Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.
We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as...