1973 Ford Mustang

Sold individually # 374212-S

Reservoir Attaching Nut 351335-S38 - Used Nuts for attaching the oil reservoir to the pump. The larger of the two nuts goes against the can. Threads of 5/8"-18 to fit the high pressure port. This is a pair of nuts, one tall and one short. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, except for 1970 with 351 engine, and Mustang with 302 engines. 1970 302 / 351 engines used a different pump with an offset...

This USB flash drive contains the complete Autolite 4300 carb information from overhauling, to diagnosis and repair. A must for anyone planning to work on their own carburetor. This USB contains detailed instructions on disassembly and assembly of all major components. This USB version of this manual is a great option for international customers. Light weight, and all you need is a PC, laptop or tablet (with USB support), and you can plug this drive in and access all the...

The automatic seat back release option for 1973 Mercury Cougar and Ford Mustang. The automatic seat back release would pull the release lever on both of the bucket seats. This only happens when the either the driver or passenger side door is opened. Kit comes with the 1973 specific wiring harnesses from the solenoid, includes 3 pin switch for the passenger pillar post, relay, solenoids, plug for retractable seat belts, and cross over wiring. This option is best added to seats prior to...

Replaces Ford Part #: D3AE-9C485-AFA

Left side axle, 28 spline 27-13/16 inch length. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note 429 CJ equipped Cougars came with heavy duty 31 splined axles.

Right side axle, 28 spline 31-7/8 inch length. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note 429 CJ equipped Cougars came with heavy duty 31 splined axles.

Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare housing with proper axle pad spacing for all 1971-1973 Cougars. Over-sized shipping length.Axles needed: Passenger side - 32 inches long, Driver side 28 inches long.

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1971-73 have the same overall width of 61 inches.   Rear axle assembly - Housing, Axles, brake backing plates, and third member. As removed from a 1971-73 West Coast Cougar organ donor car. We...

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

Backer board for the sill plate on any 1971-73 Mercury Cougar or Ford Mustang. Also called a shield, it bridges the gap over the channel for the wiring harness. It is adjacent to the sill plate, and keeps the carpet from dropping into the exposed channel. This is a used part, and made from fiber cardboard type of material. See our reproduction item in the related items for a lower cost and made from more sturdy material. Original Ford part number D1ZZ-6513218-A. Two required per car, sold...

Backer boards (PAIR) for the sill plate on any 1971-73 Mercury Cougar or Ford Mustang. Also called a shield, it bridges the gap over the channel for the wiring harness. It is adjacent to the sill plate, and keeps the carpet from dropping into the exposed channel. This is a new part, and made from durable non paper material. See our  related items for used. Original Ford part number D1ZZ-6513218-A. Two required per car, sold as a pair.

This is the 3 hole version of the ball joint for the 1967 - 1973 Cougar and Mustang. Right is same as left. Two required per car. Hardware included. made in Tiawan.

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

D3ZF-9600-AA Air cleaner base for all 1973 H code 351-2V engines. About 14.75 inches in diameter. Ford part number D3ZZ-9600-A.  Does not include snorkel.

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. For 1972-73 Mercury Cougar and Ford Mustang all with V-8 engines.Positive cable is 10 1/4" center to centerNegative cable is 42" center to centerGround wire is 41" center to center Replaces Ford Part # :...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For all 1972-73 Mercury Cougar or Ford Mustang with 43-55 AMP alternators and V-8 engines. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part...

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

Everything you need to hold the battery down on your 71 -73 Cougar or Mustang. Included in this kit are the two stainless steel J-bolts, the hold down bracket and the hold down clamp.

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

NOS service replacement battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars.  Replaces Ford Part #: D0OZ-10732-B.

Exactly like the originals. This group 27 battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Supplier misidentifies this part as D1ZZ-10732-B. Replaces Ford Part #: D0OZ-10732-B.

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New front Inner wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.378 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

New front outer wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.865 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness: 1/4" Replaces Ford Part Numbers: F23Z-3517, C1AA-3517-A, C3AZ-3517-A, C7SZ-3517-D, D0AZ-3517-A, F23Z-3517-B * - may not fit some 67 Mustang applications with a fixed column as these used Ford...

D2OZ-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1972 - 1973 Mercury Cougar and Ford Mustang with 351 engine and automatic FMX transmission, code X on your door data plate tag. Ford master part number D2OZ-7976-A.

Correct for 1971, 1972 and 1973 only. 351-2V and 351-4V engines , including Boss 351 for 1971 - 73. Ford part number D1TZ-6392-A and D1TZ-6392-C. Shipped bare, no hardware or clutch fork.

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Used cigar or cigarette lighter bezel for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A and D1ZB-15053-A

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

Reproduction headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang.  Replaces Ford part number D1ZB-11649-AC.

Used headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang. Good used bezel with shiny chrome. May have one small nick in the chrome or one broken plastic stud on the reverse.Replaces Ford part number D1ZB-11649-AC.

Used bezel for the driver side power seat switch on the 71 - 73 Cougar or Mustang. Ford part number D1ZB-14A706-AA This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Replace that old, pitted, and cut up radio bezel with this quality concours part. This is a Mustang piece that will work on your Cougar but is slightly different. The easiest way to identify a Mustang bezel from a Cougar bezel is that Mustang had four mounting holes and Cougar had five. Will need slight modification to fit Cougar. Replaces Ford Part #: D1ZZ-18842-A.

Reproduction wiper switch bezel for the 71 - 73 Cougar and Mustang. Replaces Ford part number D1ZB-17C564-AC.

Used wiper switch bezel for any 1971-73 Mercury Cougar and Ford Mustang. Good used bezel with shiny chrome. May have one small nick in the chrome or one broken plastic stud on the reverse.Replaces Ford part number D1ZB-17C564-AC.

Bleeder screw for your 1968 - 1973 Cougar or Mustang Calipers.

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1971-73 variety, which have specific colored wires and leads....

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

New rubber body plug, fits 1-3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Typical application is rear leaf spring access.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377356.

New rubber body plug, fits 1-1/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some of the holes include: inner frame rails at radiator, center of firewall, and side of cowl.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377936.