1973 Ford Mustang

Reproduction center cap adapter kit for installing Legendary center caps on the Legendary Series GT9 wheels. The spacing is a bit deeper on these specific wheels, so this adapter kit comes with special adapters and longer screws.  This kit is intended to make original and after market Mag 500 and Style Steel wheels center caps work on the Legendary Series GT9 wheels.  Please note that the included screws may not fit the thread pattern of some center caps.  The plates will...

Adapter tube for connecting the fuel vapor purge tube to the air cleaner base. Can be either blue or black in color.

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the black colored adhesive and is the 5 ounce size.

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the yellow colored adhesive, the factory used yellow adhesive on the weather stripping and is the 2 ounce size.

New 5oz tube of yellow weatherstrip adhesive for installing the rubber weatherstripping found on the Mercury or Ford. This 3M brand adhesive is a great match to the yellow colored adhesive that Ford used to attach the weatherstripping on many of it's vehicles back in the day.

Ford started using this alternator adjusting bracket sometime in 1973. It mounts to the rear of the alternator. Fits any 1973 Mercury Cougar and Ford Mustang and likely many other Ford cars with 351 engines. It works with the 1970-73 front mounting bracket. Replaces Ford part number D3AE-10145-C.

Used alternator adjusting arm for any 1970-73 Mercury Cougar, Ford Mustang, or generally Ford anything with 302, 351, or Boss 302 engines. This can be used on 1973 cars, Ford did switch to a different alternator bracket that tightened the alternator from the back sometime in 1973. Replaces Ford part number D0OE-10145-A, listed in the Motorcraft catalog as GY-938Also fits:Comet Montego

This high performance alignment kit replaces the factory eccentric bolt and cam that holds the lower control arm to the frame. The eccentric cam is used for setting wheel camber. When the eccentric is turned, the lower arm moves in or out changing camber. Stock eccentric cams can slip or rotate going over bumps, allowing the alignment to change. Which is the cause of many worn tires. The lower control arm adjusting cam eliminator kit replaces the eccentric bolt and cam with non slipping...

Sleeve and hardware for joining the inner and outer tie rods together. This also is a 'toe in' adjustment part. Sold individually, two needed per car. Replaces Ford Part #: C2AA-3310-A

384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

This air cleaner assembly never came from the factory on any Cougar, but was an over the counter option available from your Ford dealer. If you have a very nice hood blanket I would think twice before using it in conjunction with this air cleaner assembly as it will leave an imprint. To avoid this problem with small block cars you can use a lower profile carburetor spacer, but on big block cars this is not an option due to the already thin design of the factory carburetor spacer. This will...

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-2V Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. Located on the top of the air cleaner.  11-1/2 inch span, fits the smaller diameter air cleaner available in 1972.Fits the following models with a 351 2 barrel Regular Fuel engine:...

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-2V Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. Located on the top of the air cleaner. Fits the following models with a 351 2 barrel Regular Fuel engine: 1973 Cougar 1973 Mustang ...

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-4V Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. located on the top of the air cleaner. *Note - Will not fit 1968-72 air cleaner lids that are 18 inches in diameter.Fits the following models with a 351 4 barrel engine : 1973 Cougar1973 Mustang ...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Complete heater and A/C control assembly includes bezel or face plate, bracket control mounting plate, electrical and plastic vacuum switches. Functional, driver quality, heater control assembly. This unit is for 1972-73 Cougars and Mustangs produced after 1-3-1972. The prior years 1971-72 assembly without the plastic vacuum switch assembly will fully interchange with this unit. Knobs and light socket wiring harness not included. Ford part # D2ZZ-19980-A. *RESTORATION TIP* If you like to...

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. Air Filter Height (Inches) : 1.974" Air Filter Height (mm) : 50.14 mm Air Filter Bottom I.D. (Inches) : 9.03" Air Filter Bottom I.D. (mm) : 229.36 mm Air Filter Bottom O.D. (Inches) : 11.25" Air Filter Bottom O.D. (mm) : 285.75 mm Air Filter Top I.D. (Inches) : 9.03" Air Filter Top I.D. (mm) : 229.36 mm Air Filter Top O.D....

These filters feature the correct color of filter paper and an red/orange molded face. In addition, they have the correct "round hole" design on the outer shell. Fits Mustang 1965-67 K code HiPo 289 and 1968 Mercury Cougar GT-E W code 427-4V engines, that were originally equipped with the chrome high performance air filter assemblies. Please note: this filter will NOT fit a standard Ford air cleaner Replaces Ford Part #: B7SZ-9601-A. ...

Correct dimensions, good fit. Will show minor cracks in rubber but will not affect performance and cannot be seen when installed. Replacement air cleaner for the 1967 - 1973 Mercury Cougar Walking Cat Oval Air Cleaner, as well as other Ford oval air cleaners.

This 1965 Mustang alignment pin is not correct for the 1969 to 1973 Cougar but it will work. See the image to the left to see the comparison to an original 69 pin.

Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock

Good used 10 blade alternator fan.Ford Part #: DOAZ-10A310-B.

Contains nut, lock washer, and spacer. Fits all Ford alternators.

If after installing a new stereo system you experience unwanted motor whine or engine noise, check all grounds on radio, amp, etc. If you still have the noise, this filter may help.Instructions included.

Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually 

This plate is what is located on the backside of your door jam where your striker threads in on the driver side.

This plate is what is located on the backside of your door jam where your striker threads in on the passenger side.

Threaded anchor that slides into the trunk hinge on each side. Sold individually, two needed per car. These are for Cougar and Mustang built after approximately 3/31/1971. Look for bolt spacing of 4-1/4 inches on those trunk lids.  Ford number C9AZ-6242752-A.*Note - Trunks prior to March 31, 1971, did not use this anchor plate. I think that they had a bolt spacing of 4-1/2 inches.

Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang

Designed for optimum AM/FM reception. Excellent solution where a conventional antenna is not desirable (ie you do not want the antenna sticking out of the top of your fender), or when you want a power antenna or just better reception without having to replacing the factory antenna with a non-original looking antenna. Allows for complete removal of factory antenna or for the factory antenna to be disconnected and left in place to maintain the factory look.  Multiple mounting options...

This economy reproduction is not an exact copy, but does have a similar rectangle base. This is not a retractable antenna. Replaces part # C8ZZ-18813-A.

Easily replace the whip style antenna on your 73 just by unscrewing your current antenna mast and screwing in this new 100% correct stainless exact replacement. Replaces Ford Part #: D3AZ-18886

Very correct kit for the 1973! Not only does this kit include all the correct hardware, but also a photocopy of the original Ford template showing where to place the antenna on the passenger side fender. The rectangular base gasket is actually not correct for a Mercury Cougar as it has a Ford Mustang part number and is of a different shape and thickness. To retain the exact, correct angle on your 1971 - 1973 Mercury Cougar mast you will want to reuse your thicker original gasket. We usually...

Mustang part that has incorrect thickness and a slightly different overall geometry to it. We also carry the correct Cougar version of this gasket, but only in used form.Replaces part # D1ZZ-18898.

D1ZZ-223A58-A Lower door guide insert to prevent rattling of the window. Two of these inserts are inserted into the lower door guide after the door glass run is installed. Plastic piece that is subject to cracking. Two needed per door, item sold individually. Click on images to enlarge. ...

Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.

Replica antifreeze tag that would have been found on the 1970 - 1973 Cougars and Mustangs when they shipped from the factory. See the product images for an example of factory placement.

This is the arm rest base for the driver or passenger side on any 1971, 192 or 1973 Mercury Cougar with standard interior as well as some Mustang trim levels.  Also fits multiple other Ford /  Mercury cars of the same vintage.Replaces Ford Part Number: D1AB-5724144

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Mini console or consolette ashtray, for 1971-73 Mercury Cougar or Ford Mustang. Has ball bearing rollers, and dual cigarette extinguishers. Color keyed to the console and interiors, include a desired color in the notes or comments section of your online order. We will try to find your color, easy to paint with vinyl paint.

Sold individually # 374212-S

Reservoir Attaching Nut 351335-S38 - Used Nuts for attaching the oil reservoir to the pump. The larger of the two nuts goes against the can. Threads of 5/8"-18 to fit the high pressure port. This is a pair of nuts, one tall and one short. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, except for 1970 with 351 engine, and Mustang with 302 engines. 1970 302 / 351 engines used a different pump with an offset...

This USB flash drive contains the complete Autolite 4300 carb information from overhauling, to diagnosis and repair. A must for anyone planning to work on their own carburetor. This USB contains detailed instructions on disassembly and assembly of all major components. This USB version of this manual is a great option for international customers. Light weight, and all you need is a PC, laptop or tablet (with USB support), and you can plug this drive in and access all the...

The automatic seat back release option for 1973 Mercury Cougar and Ford Mustang. The automatic seat back release would pull the release lever on both of the bucket seats. This only happens when the either the driver or passenger side door is opened. Kit comes with the 1973 specific wiring harnesses from the solenoid, includes 3 pin switch for the passenger pillar post, relay, solenoids, plug for retractable seat belts, and cross over wiring. This option is best added to seats prior to...

Replaces Ford Part #: D3AE-9C485-AFA