1969 - 1970

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S

Complete engine mounting hardware kit for the 1969 351W engine. See below for a list of included hardware. Click on images to enlarge.

Complete engine mounting hardware kit for the 1970 351W engine. See below for list of included hardware. Click on images to enlarge.

Complete engine mounting hardware kit for the 1969 351W with A/C. See below for a list of included hardware. Click on images to enlarge.

Complete engine mounting hardware kit for the 1970-71 351C 2-barrel engine. See list below to see what is included. Click on images to enlarge.

Complete engine mounting hardware kit for the 1970-71 351C 4-barrel engine. See below for list of incuded items. Click on images to enlarge.

Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...

AMK engine fastener kit for 1969 Mercury Cougar and Ford Mustang / Fairlane all with R code 428 Cobra Jet engines. This kit claims to have 157 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck, water...

Complete engine mounting hardware kit for the 1970 428 CJ / SCJ engine. See list below for included items. Click on images to enlarge.

Complete engine mounting hardware kit for the 1969 Boss 302. See list below for included hardware. Click on images to enlarge.

Complete hardware kit. See what is included in the list below. Click on images to enlarge.

Reproduction mounting kit contains everything you need to install the cowl cover on the 69 - 70 Mercury Cougar.

Replaces Ford part # 55806-S

This specialty screw attaches the gas pedal to the throttle linkage. Fun fact: the head looks like Phillips (and that works fine) but this is actually designed for a Pozi bit.

Self threading speed nut for attaching "COUGAR' scrip emblems to the rear quarter panel of any 68 - 70 Mercury Cougar. Sold individually, 4 needed per emblem. Whereas these work fine, the originals were an acorn style nut and look very different.

Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Replaces Ford part # C2DZ-6A529 Sold Individually.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

New 3/8-16 nut for the shock tower shock cap. Three nuts used on each cap, 6 total per car. Sold individually.Replaces Ford part number 377706-S7.

Perfect fit.

These were used to attach the taillight assembly to the tail panel on a 1969-70 Cougar. Five were used per taillight, 10 required in all for one car. Sold individually. Also the same size for 1967-68 tail lights.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

Reproduction heater duct nylon rivet #375064-S is sold individually.

Nice reproduction of the prop rod used on the 1970 Eliminator. This will work on any 1967 - 1973 Cougar that has had a spoiler installed. The pictures of the installed original prop rod were taken at the 2008 PROWL Cougar show hosted by Cascade Cougar Club. The concours correct BOSS 302 Eliminator pictured is owned by John Benoit in Edgewood Washington. Click on images to enlarge. The above picture shows the approximate location of where to drill the hole in the passenger side rear quarter...

Four needed per fan shroud. Sold individually.Ford Part Number: 383152-S

Fits Standard and XR7 Sold in Set of 4.

Fits Standard and XR7 Sold as a Kit as Pictured.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Reproduction Lower Windshield Moulding Retainer for the 1969 1970 Mercury Cougar or Ford Mustang 

New lower windshield moulding retainer screw. The retainers slide into the lower stainless steel windshield moulding and attach with these screws into the cowl top. #8 x 1/2 inch hex washer head screw with 1/4 inch drive. Several suppliers or styles of screws were used, some with plain hex some with a slotted hex. We stock the 1/2 inch length #8 hex head washer head screws. Sold individually, 7 total clips hold in that lower windshield moulding on 1969-70 Mercury Cougar and Ford...

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

Sold individually Zinc with Bi-wax sealer (dark silver with gold color on threads)

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold individually. Two needed for globe box cable 1967-70 Mercury Cougar. 3 needed for installation of turn signal switches 1967-73 Mercury Cougar or Ford Mustang.Ford number 379203-S. Phosphate & Oil (gray-black)

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually. Zinc (dark silver)

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Correct size, style, and color screw for all 1969-70 Mercury Cougar front turn signal bezels. Sold individually, 4 total needed per car.Replaces Ford part number 52445-S.