1969

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7MB-17A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-17-A. Left hand high beam holder. Ford part # C7MB-17A ...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7OB-47B and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-47-A.  Ford part # C7OB-47B.

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "H", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68 Mercury...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Requires you to PRE-PAY a core charge of $30. Used grade "B" headlight door actuator for your Mercury Cougar. This grade B actuator has been reconditioned with new seals but will still slowly leak down after time as not all of them will function as new after being reconditioned. These actuators are sold individually on an exchange basis or outright (for an additional core charge). One actuator actuates both headlight doors on the 69-70. This unit also comes with a 30 day warranty. Ford part #...

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

C9WY-13A155-A Hinge that the hideaway headlamp covers attach to on the grille. This is the driver side only. See C9WY-13A154-A for the passenger side hinge.

C9WY-13A154-A Hinge that the hideaway headlamp covers attach to on the grille. This is the passenger side only. See C9WY-13A155-A for the driver side hinge.

C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental 1969 - 1971 Lincoln...

C9AZ-13A163-C Coil spring for the hidden headlamp hinges on all 1969-70 Mercury Cougars and 1969 full sized Ford cars with hideaway headlights. Sold individually, one per side. 1969 Mercury Cougar including XR7 and Eliminator. 1969 Ford LTD 1969 Galaxie and Galaxie XL 1969 Country Squire Wagons

Used hood latch for a 1969 Mercury Cougar, it will fit the 1970 too. Starting in 1969 until 1970, Mercury had three different hood latches. This early 1969 version has the shortest handle, and is the hardest to operate. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number C9WY-16700-A.

Used hood latch for a 1969 Mercury Cougar, it will fit the 1970 too. Starting in 1969 until 1970, Mercury had three different hood latches. This late 1969 version has the medium length handle. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number C9WY-16700-B.

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

Attaches behind the drivers side horn on all 1969-70 Mercury Cougar and Ford Mustangs with air conditioning. We believe that this part was installed to maintain clearance with the A/C condenser. Ford part number C9ZF-13925-A as seen in the 1969 Electrical Assembly Manual.

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here! Does...

Reproduction nuts for mounting the 1969 Mercury Cougar headlight door or eyelid cover to the hideaway headlamp hinge.

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

These simple little grille repair clips have been needed since these cars were new! Over the years I have seen many home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will list the all the different FoMoCo applications from the era that these clips apply to. These clips are sold as a set of four. Click on images to enlarge. ...

Shaft assembly for driver side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

C9WY-13B014-A Shaft assembly for passenger side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

Repro bushings (pair) that mount to the grille for the headlamp operating shafts. These hardly ever survive after 40 years. Technically not needed, and most never knew they existed. Sold as a pair, one for each side. When mounted these are tight, it was no wonder they are seldom seen on cars. Even the NOS bushings are tight. We recommend polishing the headlight shaft with emery or sand paper, to make both sides smooth. Definitely add a little bit of lubricant too. Replaces Ford part number...

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

1969 Hidden Headlight Cover Stop Bracket with nut, for all 1969 Mercury Cougar and 1969 full sized Ford and 1969-70 full sized Mercury. Mercury part number D0MY-13A096-A.

Used Driver Side Grade B Center Grille Support for the 1969 Mercury Cougar

Used Passenger Side Grade A Center Grille Support for the 1969 Mercury Cougar

This grade "B" support will be rust free but will need minor straightening on the lower mounting tab. Once worked on the damage should not be noticeable. Customer feedback; Hey Don, I've been ordering parts for my '67 over the last few months from your company. I just want to let you know I would recommend your company to anyone. You have been extremely helpful in every aspect. I think your site is great and easy to use. I especially liked how you call me with questions and answers...

Used  Grade A driver side support / grille center for the 1969 Mercury Cougar

Used upper support bracket for the hood latch on any 1969 Mercury Cougar. Ford part number C9WY-16707-A.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

Used headlight switch for the Mercury Cougar. This original FoMoCo unit was tested and will hold 13 pounds of vacuum. The spacer (which is specific to 1969) is not included with this unit, but you can get it right here. Ford part # C9WB-11652-B.

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

Good rust free tank taken from a Western parts car. Differs from other years in that the vacuum port is located in a different position. Located under the driver fender. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number C9WY-13A185-A.

Good rust free tank taken from a Western parts car. Differs from other years in that the vacuum port is located in a different position. Located under the driver fender. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number C9WY-13A185-A.

Used front license plate bracket for a 1969 Mercury Cougar or 1969-70 Ford Mustang. Grade A used, Best available, may have a slight curve or missing paint. Rubber bumper may be missing. New rubber bumpers available.Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Used front license plate bracket for a 1969 Mercury Cougar or 1969-70 Ford Mustang. Grade B used, will either show signs of straightening or need some straightening. Still functional, likely will not have the rubber bumper installed. Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Headlamp center shaft actuator rod clips. Sold individually, two clips needed, one on each side of the shaft. Not really needed, probably kept the shaft ends from moving during installation. We have found two different sizes of these clips. No pattern between 1969 and 1970.

Good used 1969 grille center in average condition that will be driver quality or good for rechrome. The grille will look good with the hood closed but when you inspect the backside there may be signs of a professional repair. The chrome will looked aged and may have the beginnings of pits but nothing major. Since this is an expensive part and less than perfect we do not mind sending pictures prior to sending them out. Keep in mind we offer in store credit for broken center grilles even if they...

Used grade "A" driver side (left hand) grille half for the 1969 Mercury Cougar. These will be the best we have available, taken from a Western parts car. The horizontal bars will not have any breaks or cracks, the chrome will not have any pits on the face but you will see minor pitting between the horizontal bars on the black painted areas. Often there will be a crack where the tension spring for the headlight attaches but we will include one of our grille repair clips if that is the case....

Used grade "A" passenger side (right hand) grille half for the 1969 Mercury Cougar. These will be the best we have available, taken from a Western parts car. The horizontal bars will not have any breaks or cracks, the chrome will not have any pits on the face but you will see minor pitting between the horizontal bars on the black painted areas. Often there will be a crack where the tension spring for the headlight attaches but we will include one of our grille repair clips if that is the case....

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up. If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much easier to find inner, high beam lamp distinguished by the number 1 at 12...