1969 - 1970 Seat Tracks / Seat Hardware

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

The knobs for the seat track release to adjust the position of the seat. The reproduction has a slightly deeper divot where you place your finger, and is slightly more round on the bottom, but a very nice reproduction. Replaces Ford Part #: C5AZ-6261753-BA.

The bench seat brackets are slightly different than the bucket seat brackets. Our premium grade used tracks are carefully inspected for damage before shipping. Most likely you will have to paint but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. Ford master part numbers...

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Correct for 1967 but fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. We also have the version with rectangular plates at the studs if you are wanting to match what you may have currently. ...

This Grade B set will need clean up and servicing but will not have cracks, broken studs or excessive rust. Fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version.

This adjustable linkage kit connects the left track to the right track on a bucket seat. Original Ford part number C5ZZ-6561726-A. Ford description: Rod - Front Seat Track Tie. Listed for bucket seats 1965-1970.

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

This adjustable linkage kit connects the left track to the right track on a bench seat. Original Ford part number C5ZZ-6561726-B. Ford description: Rod - Front Seat Track Tie. Listed for Mercury Cougar and Ford Mustang bench seats 1967-1969.

Grade A non lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561704-F.

Easy to install, correct tension and length. Includes All the Springs Necessary to Rebuild One Seat. Black Phosphorous Plated. Bucket or Bench seats - 2 kits required for bucket seats. Replaces Ford Parts: (2 - Track assist springs) C5ZZ-6561828-A and (1 - Track latch spring) C0DZ-6461883-A.

Comes with everything shown to replace tracks on one seat, good quality reproduction made in China. Make sure and check out our good used originals if correctness is important to you.

This listing is for the person who needs a little more leg room when behind the wheel. If your knee is pushing on your turn signal lever, or if your belly is hitting your steering wheel, this is the item for you. Very easy to install, bolts right up to your existing seat tracks. You can expect about a 1/4" height difference. Sold as a pair, enough to do one seat. Check out this video

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

1969-70 actually used a star head bolt but these are a much more user friendly screw that will work in its place. Sold in a set of four which is what you will need for one seat.

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...