1968

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7MB-17A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-17-A. Left hand high beam holder. Ford part # C7MB-17A ...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7OB-47B and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-47-A.  Ford part # C7OB-47B.

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16-A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7MB-16A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-16-A. Ford part # C7MB-16A.

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "RL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL GRADE B ACTUATORS COME WITH A 60 DAY WARRANTY. You can find the seal rebuild kit here. Used grade "B" headlight door actuator for your Mercury Cougar. Every once in a while (not often) we will...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. NOTE - If your actuators are the type with the internal spring (Thunderbird actuators had a failsafe internal spring) we cannot accept those as cores. An easy way to tell which actuators are the...

Pair of reproduction headlight actuators for the 67 - 68 Mercury Cougar. Manufactured to meet and exceed factory specs without the need for additional parts or modification. Keep in mind when you buy these units WCCC will pay $50 for the pair of your rebuildable core units. Our video below explains how to determine if your cores are acceptable. Check out this video on how to rebuild your existing headlight vacuum actuators ...

Reproduction rubber hose connector as used on the 1968 headlight hoses. A pair of these connectors connects the color coded hoses that lead to the headlamps from the short hoses coming out of the firewall from the headlight switch. Replaces Ford part # C8WY-13A170-B

This part affixes to the backside of the headlamp cover and acts as a hinge. The design was changed 12-15-67 so you will have to know the date in which your grille was built. All 1967 model year Cougars were built prior to 12-15-67 but we mention this here as many 1967 Cougars have had 1968 replacement parts installed over the years. The brass bushings have been inspected for wear, no collision damage and no rust. Both adjustment bolts are included with the hinge, the bolts in which the hinge...

Passenger side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The brass bushings have been inspected for wear, no collision damage and no rust. If you try to use a hinge from a 1967 built prior to 12-15-67 it will not fit on your 1968 Cougar. Ford part number C8WY-13A154-A. Check out this video ...

Driver side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The design was changed 12-15-67 so you will have to know the date in which your grille was built. All 1967 model year Cougars were built prior to 12-15-67 but we mention this here as many 1967 Cougars have had 1968 replacement parts installed over the years. The brass bushings have been inspected for wear, no collision damage and no rust. Both adjustment bolts are included with the...

Used driver side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The brass bushings have been inspected for wear, no collision damage and no rust. If you try to use a hinge from a 1967 built prior to 12-15-67 it will not fit on your 1968 Cougar. Ford part number C8WY-13A155-A. Check out this video ...

C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental 1969 - 1971 Lincoln...

Used Grade A - Hood latch brace, brace only, fits all 1967-68 Mercury Cougars. Straight piece, this is typically the only part of the hood latch assembly that gets damaged in a collision. This is Grade A used, we also have Grade B braces that need some massaging to be perfect.Ford part number C7WY-16747-A.

Used Grade B - Hood latch brace, brace only, fits all 1967-68 Mercury Cougars. Grade B brace that will need some massaging to be perfect. These are fairly easy to get straight enough cosmetically. We also sell complete assemblies and Grade A used braces.Ford part number C7WY-16747-A.

Good used, rust free latch that is in good working order. This unit has not been straightened or pushed out after being in a fender bender. We also have many grade "B" latches in less than perfect condition. We also have the individual components listed. Check out this video ...

Used, hood latch assembly that is in good working order. This unit will have a bit of metal shifting on the brace portion. Can be straightened fairly easily We also have many grade "A" latches. We also have the individual components listed. Check out this video ...

Used hood release latch by itself, this is a component of the hood latch assembly for any 1967-68 Mercury Cougar.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position. We do offer the correct used Cougar horns.Replaces Ford Part # C7ZZ-13832. These horns are close but not correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B...

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position. Replaces Ford Part # C7ZZ-13832. These horns are close but not correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used...

Used to mate the headlight vacuum hoses together at the front cross beam under the core support. Notice it still has the remnant of green paint used to identify where the color coded hoses are to be placed. Cougar part number C7SZ-13A169-A.

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. Kit includes used check valve and fittings shown, but does not include headlight switch. "I found a good way to...

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Original Ford part number 373845-S.

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Dimensions: 3/16 x 3/16 x 1/4

Used Grade "A" Grille Center Medallion for the 1967 and 1968 Mercury Cougar. These will not have pits or damage to the chrome. Unfortunately the softer black background insert will often times have marks. Ford part # C7WB-8B344-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Rechromed Grille Center Medallion for the 1967 and 1968 Mercury Cougar. Unfortunately the polishing and plating process will take away much of the detail. Cores must be pit free or very close to. Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If...

Used aluminum "Mercury Man" head for the center grille medallion. These are just pressed and swedged into the die cast bezel and come out easily with a light tap from behind. Keep in mind these highly amplified pictures make the emblem look much worse than it really is. Do know that the one you get will have light road debris wear but no major scratches, pits or scrapes. You will also want to replace the background foil decal when you purchase this emblem. Part of Ford assembly C7WY-8A223-A ...

Restored passenger side (right hand) center grill moulding / trim for the Mercury Cougar. As you can tell, price wise, you are much better off to purchase the entire set together as opposed to one at a time.Ford part # C7WY-8A158-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim...

Used passenger side (right hand) center grill moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches, or corrosion. Perfect for your daily driver that is in above average condition. Ford part # C7WY-8A158-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for...

Core passenger side (right hand) center grill moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness. Ford part # C7WY-8A158-A. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. Check out this video ...

If your Cougar came from a region that uses road salt your buckets are probably rusted in the corners or worse. Our dry "West Coast" buckets are 100% rust free and the mounting tabs are not broken from the removal of stubborn bolts. They will not be bent or damaged in any way. Keep in mind we do have grade B brackets for much less that only have minor bends or blems that could be easily corrected. *NOTE* These parts are far more important than most people realize. If they structural integrity...

These driver quality buckets are solid but will have a small bend, hairline crack or the beginnings of rust in a corner. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in these brackets are very powerful and if these brackets do...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable.  NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS.   *NOTE* These...

These driver quality passenger side headlight buckets are mostly solid but will have a small bend, hairline crack or the beginnings of rust in the corner closest to the battery. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable. NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS. *NOTE* These parts are far more...

This is a 100% accurate reproduction down to the captured lock washer and black Zinc coating. The only difference is that these are made from a substantially better grade of steel than the originals. These often break when you try to remove them to replace the vacuum actuator so if you are planning on doing that procedure we highly recommend buying these in conjunction with the actuators. Sold individually, two required per car. Cougar part number C7SZ-13A173-A. Also Fits: 1967 Ford...

This is the bolt that often gets destroyed when you try to remove it from the bottom side of the headlight bucket. Our West Coast Cougars come apart a little easier so we often are able to pull them with minimal effort. Cougar part number C7SZ-13A173-A. Application includes: 1967-68 Mercury Cougar and XR7, 1967-68 Ford Thunderbird, 1969-71 Lincoln Continental MK III. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in...

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Check out this video ...