All Available Parts - 1967 Mercury Cougar

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing, very tough part for us to keep in stock. The metal version is a better part and you can get our metal reproduction unit right here!Ford part # C7ZZ-6501891. ...

Under dash bracket used to mount the pull cable for the fresh air vent on the driver side of your Mercury Cougar or Ford Mustang.

High Quality cloth wrapped heater duct hose. This is the correct length for most cars, but will need to be cut for proper fit in some applications. Hose diameter: 2 1/2"

24" hose with metal coil (like original) instead of plastic coil found in most. Coils are wrapped in a 6+ mil plastic rather than the 3 mil plastic that you can easily put your thumb through. Does not come with clips. May require being cut to fit some applications. 2 required per car. Replaces Ford Part #: B5A-18556-C.Replaces Ford Part #: B5A-18556-C.

Black plastic retainer for attaching the direction air conditioning vent registers.

Reproduction Air Conditioning Vent Air Door for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Reproduction Air Conditioning Vent Air Door Axle for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Round air conditioning vent registers for all 1967-68 Mercury Cougar and Ford Mustang with factory A/C.

Nice reproduction fresh air vent cable pull assembly. Comes with dash mounted bracket as shown. Much stronger construction than the originals, which were made with a plastic sleeve instead of metal.Replaces Ford part number C7ZZ-6501891-A and C7ZZ-6501891-C.

All new parts for rebuilding the right and left shutoff butterfly in the air conditioning register vents. Fits all 1967-68 Mercury Cougar and Ford Mustang with factory A/C. Kit includes 2 knobs, 2 black butterfly vent doors, 2 shafts, and 2 retainers. All of these individual parts are also separately. Chrome vent registers and vent retainers are also available.

Reproduction factory air conditioning vent register knob. This knob controls the black vent door or valve inside the round registers. These will fit the original axle shafts, but will need to be attached with some super glue or other adhesive. These new knobs fit our reproduction axle shafts that have new splines on them perfectly. Please note the position or orientation of the knob in relation to the position of the internal black plastic butterfly.

Grade A used A/C center vent for standard (non XR7) model Cougars. These will have almost perfect chrome plating, minor blemishes only, no major pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade B versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Grade B used A/C center vent for standard (non XR7) model Cougars. These will have some defective chrome plating, and pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade A versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Grade B used A/C center vent for XR7 (non Standard) model Cougars. These will have some defective chrome plating, and pitting. Fits the XR7 model (65B) Cougars with woodgrain dash faces. See our other listing for Grade A versions of this air conditioning center register or vent. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Grade A used A/C center vent for XR7 (non Standard) model Cougars. These will have some minor chrome blemishe in the plating, but no heavy pitting or damage. Fits the XR7 model (65B) Cougars with woodgrain dash faces. See our other listing for Grade B versions of this air conditioning center register or vent. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Under dash wiring harness assembly for all 1967 Mercury Cougar and Ford Mustangs with integral, or factory installed air conditioning. All wiring harnesses are test and inspected by our electrical department.Replaces Ford part number C7ZB-19945-A.

Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade A version will be free of all but very cosmetic defects. Meaning no broken tabs, or torn or missing screens. Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with heaters only used two individual nozzles.

Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade B version may have one of the following: crack or chip, have a broken tab, or a torn or missing screen. B grades will install and work, they just may need a bit of duct tape or be held on with 3 of the 4 screws.Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with...

Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...

Clips that attach to the dash for mounting the defrost nozzles. Package of 4 clips and 4 nuts, enough for non air conditioned cars, same clips used for air conditioned cars. Cars with A/C only need 3 clips installed though. Nuts are different than OEM, but work fine, we suggest adding a flat washer though.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, switch, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door. Stapled foam seal to center vent may not be perfect.Replaces Ford part number C7ZA-19740-B.

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.

Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...

Used plastic plated plate that goes between the dash bezel and dash pad on any 1967-68 Standard model Mercury Cougar with factory air conditioning. This is for the center vent and is has a Ford casting number of C7WB-65044E88. These originally were chrome vacuum plated, like the dash. These will have some degradation or flaking chrome. No breaks or cracks on the plastic.

Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Nice fit, made of plastic. Will work with or without console, has slightly wider wings for clearance of the rear of the factory installed consoles.

Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs without a console.

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade A vents will not have any cracks or breaks.

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade B vents will mostly have a missing metal bracket and / or small crack or break usually around the mounting holes.

Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade A vents will not have any cracks or breaks.

Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade B vents will have a small crack or break usually around the mounting holes, but will not effect it's functionality.

Vacuum switch that attaches to the air conditioning lever assembly on all 1967-68 Mercury Cougar and Ford Mustangs with integral A/C.Ford number stamped C7ZA-19B919.

We offer this "Core Grade" assembly for those that purchase the various 1967 reproduction air conditioning bezels. This assembly will provide the needed 'guts' for behind the various 1967 Mercury Cougar or Ford Mustang A/C and heater control bezel. A Complete A/C heater control assembly includes bezel or face plate(bezel will be pitted and possibly broken), bracket control mounting plate, electrical and vacuum switches, and hardware. *NOTE* - Does not include knobs or cable.Ford part #...

Reproduction set of A/C register connectors for Mercury Cougars and Ford Mustangs with integral A/C. These mount directly behind the round dash vents and work well with both the original vents or our high quality reproduction vents.

Work perfectly with our reproduction A/C registers.Ford part # C7ZZ-19C692-A.

Passenger side A/C duct register, or elbow, connector for Mercury Cougars and Ford Mustangs equipped with integral or factory A/C. These elbows work perfectly with our reproduction A/C registers.Ford part # C7ZZ-19C692-B.

Reproduction plastic plate that goes between the dash bezel and dash pad on any 1967-68 Standard model Mercury Cougar with factory air conditioning. This is for the center vent and is has a Ford casting number of C7WB-65044E88.Note: The lip of the plate points downward. The plate slides in behind the dash face pad, see above photo for reference.

Reproduction A/C center vent for XR7 (non Standard) model Cougars. These are great quality vents with bright chrome finish. Fits the XR7 model (65B) Cougars with woodgrain dash faces. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Reproduction A/C center vent for standard (non XR7) model Cougars. These are great quality vents with bright chrome finish. Fits the standard model (65A or 65C) Cougars with padded dash face pads. *Plastic chrome vent plate included.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

This new chrome interior A/C vent register kit is spot-on! Comes with driver and passenger A/C vents, knobs and standard center vent with cover plate.

This new chrome interior A/C vent register kit is spot-on! Comes with driver and passenger A/C vents, knobs and XR7 center vent.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. We also offer another valve that was used for a period of time see the related evaporator valve.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service. This valve was originally stickered with a FoMoCo tag and...

Senses temperature to open and close the expansion chamber and made just like the original.Will work with both R12 and R134 systems.Replaces part #: C7ZZ-19849.

These beautiful reproductions replace those rusty and corroded originals that just look nasty. 5/8" Replaces Ford Part #: C6AZ-18599-B

These beautiful reproductions replace rusty and corroded originals that just look nasty.5/8" Replaces Ford Part #: C6AZ-18599-S

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

This valve is used on Mercury Cougars and Ford Mustangs equipped with factory A/C to stop the flow of warm coolant when A/C is on.This valve is functionally the same as the OEM, but has obvious cosmetic differences from the factory valve.Replaces Ford Part #: C7ZZ-18495-A.

This is used on Mercury Cougars and Ford Mustangs equipped with factory A/C. This is the bracket for the valve that stops the flow of warm coolant when A/C is turned on. This is an exact reproduction and has the zinc dichromate finish.

This unit is for Mercury Cougars and Ford Mustangs, is pre-assembled, and includes the drier and all brackets.

Reproduction A/C suction service valves for Mercury Cougars and Ford Mustangs equipped with factory A/C.

These are correct reproductions of the A/C discharge service valve that comes with plastic caps. if you would like the correct aluminum valves, we sell those separately.

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade A hose that is not cracked, may have a small cosmetic scuff in the foam, and the clips will not be broken. Two required per car, sold individually. We also have a listing for Grade B condition, that will have a minor issue or two. Ford part #: C7WY-19B680 or B5A-18556-C.

Both ends have 90 degree molded ends. Attaches heater core to water heater control valve.Replaces Ford Part #: C7ZZ-18472-CVAC.

Concours correct A/C discharge hose for Mercury Cougars and Ford Mustangs.Replaces part # C7AZ-19972-A or C7ZZ-19972-A.This hose is compatible with both 134a and R12 refrigerants.

Concours correct and constructed in original Ford style black thermoplastic material with a nylon barrier. This hose assembly is built to be compliant for R-12 or 134a refrigerants.NOTE: We have three hoses from a previous supplier that we have available for about half the price. The only difference would be that instead of the thermoplastic material, these are the standard rubber type hoses. Pick one up here. ...

Concours correct A/C sight glass hose with a 90° fitting for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, C7ZA-19835-A or C7ZA-19837-D both can be the correct part number. This hose is approximately 74 inches long and this line also incorporates the site glass. The Ford MPC # is C7OZ-19837-A.

Regardless of which V-8 engine, C7ZA-19867-C is the correct part number. This hose is approximately 55 inches long.Ford MPC part # C7ZA-19867-C.

Concours correct white striped heater hose for 1967 and early (prior to 2/1/1968) 1968 Mercury Cougar and Ford Mustang with factory or integral A/C. Durable white striping with no mention of "Autolite" - this particular hose did not come with that marking. The 'with air conditioning' hoses have correctly molded 90 degree elbows that fit on the water valve side. Some length trimming may be needed for a tight looking fit.

New A/C vent hose with cam locks for your Mercury Cougar or Ford Mustang equipped with factory A/C. This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Two required per car, sold as a pair.Ford part #: C7WY-19B680 or B5A-18556-C.

Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.   

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Steel elbow that uses the A/C coupler from the liquid or sight glass hose to the dryer. This is an OEM Ford part that was originally part of an assembly, which included the sight glass hose, coupler, and this elbow. This elbow has the flared fitting common to the 1967-68 A/C connections. We recommend replacing "O" rings prior to installation, which are commercially available from air conditioning service centers.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. This is the uncommon version, we have a limited supply of these from original cars.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # C6OZ-19849-A. aka YG-24

This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade B hose that may have a crack or tear, or with a broken clip. Two required per car, sold individually. We also have a listing for Grade A hoses. Ford part #: C7WY-19B680 or B5A-18556-C.

Fits 1967 Cougar and Mustang with factory Heater Only Firewall and 1967 289 engine. Custom Hurricane Heat Cool & Defrost System for 1967-68 Mercury Cougar / Ford Mustang with original 289 V-8 with or w/o Power Steering. Easy to Install! Hurricane Unit mounts to firewall in place of factory heater, a/c & heater fittings pass neatly through original blower motor hole with custom rubber grommet. Electronic switching package includes correct reproduction A/C Control bezel w/ louvers. Electronic...

Used A/C suction service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Used A/C discharge service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

Hard plastic terminal covers for the alternator. Replaces Ford Part #c7zz-14056-A

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Used stamped steel single groove alternator pulley, typically these are described as being 2-7/8 inches in diameter. We find various casting numbers on them, such as: C5AF-10A352-F1, C5AF-10A352-G1, C5AF-10A352-K, C5AF-10A352-L.Replaces Ford part number C5AZ-10344-K.

This is a 'made in China' wiring harness. Quality is OK and will work for this application. Application is 1967-68 Mercury Cougar XR7 models and Ford Mustang without factory tachometer option, all with 289 or 302 engines. *Caution, not for use with Cougar standard models or Mustang with alternator warning light. *Note - Excludes California models or cars with factory Thermactor smog pump with low mounted alternators.Replaces Ford Part # C7ZZ-14305-B Door Tag 65B

Reproduction alternator wiring harness for all 1967 Mercury Cougar Standard Models, meaning Non XR7. Additionally 1967 Ford Mustang with tachometer. Excellent reproduction copied from an NOS wiring harness.Ford service number C7ZZ-14305-E, wire harness marked C7ZB-14305-E.

Nice reproduction of the original alternator wiring harness, has individually colored boots and the wire colors match up to the original Ford drawings. Application is 1967-68 Mercury Cougar XR7 models, all with 289 and 302 engines. Ford service number C7ZZ-14305-B, wire harness marked C7ZB-14305-B or C8WB-14305-C. *Caution, not for use with Cougar standard models. *Note - Excludes California models or cars with factory Thermactor smog pump with low mounted alternators ...

Nice reproduction of the original alternator wiring harness, has individual colored boots and wire colors match up to the original Ford drawings. Application is 1967 Mercury Cougar standard models or 1967 Ford Mustang with factory tachometer option, all with S code 390-4V engines. Ford service part number C7ZZ-14305-D, original harness numbered C7ZB-14305-D. *Caution, not for use with Cougar XR7 models or Mustang with ammeter gauge. *Note - Excludes California models with Thermactor smog pump...

Nice reproduction of the original alternator wiring harness, has individual colored boots and wire colors match up to the original Ford drawings. Application is 1967 Mercury Cougar XR7 models or 1967 Ford Mustang with factory tachometer option, all with 390-4V engines. Ford service number C7ZZ-14305-C, original wire harness marked C7ZB-14305-C. *Caution, not for use with Cougar standard models or Mustang with alternator warning light.*Note - Excludes California models or cars with factory...

Used bracket and pulley assembly for 1967 Cougar or Mustang with 390 engines. All pulleys with bearings are sold in working used condition. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got the parts you need! Ford part # C7SZ-8678-B. ...

Air conditioning belt tension pulley. For Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C7AZ-8678-B. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.

Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.

Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.

Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.

Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.

Fan spacer, measuring 2-7/8 inches, sometimes mentioned as 3.15" overall. Applications include 1967-68 Mercury Cougar and Ford Mustang with 289/302 and standard cooling. Reference number YA-79.Ford part # C5OE-8546-A, Ford engineering # C5OZ-8546-A.

Fan spacer, measuring 3-1/16 inches, sometimes mentioned as 3.40" overall. Applications include 1967 Mercury Cougar and Ford Mustang with 289-4V. Reference number YA-78.Ford part # C5AE-8546-B, Ford engineering # C5AZ-8546-B.

Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.

Ford part number C5AZ-6312-B. Application for 1967-68 289 and 302 engines without all of the following; air conditioning, power steering, California thermactor smog. The alternator would also have a single sheave pulley. Ford casting number C5AE-6312-A. Single sheave crank shaft pulley. About 6-5/16 inches in diameter.

C5AZ-6312-D Application for 1967-68 289 or 302 engines with air conditioning. Power steering and or California Thermactor emissions permissible. Ford casting number C5AE-B. Triple sheave 67 68 crank pulley. Inner diameters are about 6-1/2 inches, outer diameter is 7-5/16 inches.

C5AZ-6312-E Application 289 engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions.   6 5/16" wide 3" deep to mounts.  Ford casting number C7AE-6312-A. Double sheave 67 crank pulley.

C6AZ-6A312-A Two applications on 289 engines. 1. Manual transmissions and standard cooling (standard cooling is the 17 inch radiator). 2. All transmissions with extra cooling (extra cooling is the 20 inch radiator). Dual belt alternator pulley, California emissions permissible. & Without air conditioning or power steering. Ford casting number C6OE-6312-A. Double sheave 67 crank pulley. 6-5/8 inches in diameter.

C7AZ-6A312-A. Double or two groove crankshaft pulley. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. 6-1/8 inches in diameter. 1967 Application - Mercury or Ford 289 with automatic transmission and standard cooling (17 inch radiators). Without air conditioning and without power steering. 1968 Application - Mercury or Ford 289 or 302 with or without power steering. Thermactor emissions permissible. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. ...

New crank shaft pulley with 2 sheaves for any 3 bolt, 289 / 302 / 351W engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions.   6-3/8" overall diameter, has 3/8 and 1/2 inch grooves for fan belts. Replica of the C7AE-6312-A crankshaft pulley by Ford. Double sheave 67 crank pulley.

Ford casting number C4AE-6316-A. All 1967 S code 390-4V engines. 1967 only, 6-5/8 inches in diameter, cast iron construction with key way groove. This is a combination crankshaft balancer and pulley. Has the timing marks on rim. Ford Master Part number C3AZ-6312-E. Refundable $80.00 core charge when rebuildable C4AE-6316-A harmonic balancer is received by WCCC.*Note - This harmonic balancer is generally covered up by an outer crankshaft pulley when options such as air conditioning and power...

Ford casting number C5TE-6312-A. Single cast iron pulley for use with California thermactor emissions and low mount dual alternator pulleys. No other options, just the DSO 52 and 53 California engines. Ford Master Part number C5TZ-6A312-A. 6-5/8 inches in diameter. Together with the inner crankshaft balancer pulley, these now paired pulleys drive both the water pump and alternator pulleys. The Thermactor air pump pulley is driven by the 3rd outer water pump pulley sheave - only. Must use the...

Casting number C5AE-D. Triple sheave pulley used with both air conditioning and thermactor emissions. Inner pulley fits over the harmonic balancer, largest pulley is 7-3/4 inches in diameter. *Note - with the inclusion of this larger diameter pulley you must use timing pointer part number C5AE-6023-A.